Durr Dental Periomat Plus User manual

EN
Installation and Operating Instructions
Periomat Plus
2016/01SE

EN
2016/01SE 3
Content
Important Information
1. Warnings and Symbols . . . . . . . . . . . . . 4
2. General . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1 Note on Conformity . . . . . . . . . . . . . 5
2.2 General Notes . . . . . . . . . . . . . . . . . 5
2.3 Qualified personnel . . . . . . . . . . . . . . 5
2.4 Disposal . . . . . . . . . . . . . . . . . . . . . 5
2.5 Notes on medical products . . . . . . . . 6
2.6 Correct Usage . . . . . . . . . . . . . . . . . 6
2.7 Incorrect usage . . . . . . . . . . . . . . . . 6
2.8 Connecting peripheral appliances . . . 6
3. Safety . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.1 General Safety Notes . . . . . . . . . . . . 7
3.2 Electrical safety instructions . . . . . . . 7
4. Delivery Contents . . . . . . . . . . . . . . . . . 9
4.1 Special accessories . . . . . . . . . . . . . 9
4.2 Disposable materials . . . . . . . . . . . . 9
5. Technical Data . . . . . . . . . . . . . . . . . . 10
5.1 Model Overview . . . . . . . . . . . . . . . 10
5.2 Model identification plate . . . . . . . . 10
5.3 Ambient conditions . . . . . . . . . . . . . 11
6. Switch panel functions . . . . . . . . . . . . 11
Mounting
7. Set-up . . . . . . . . . . . . . . . . . . . . . . . . 12
7.1 Room for Set-up . . . . . . . . . . . . . . 12
7.2 Set-up . . . . . . . . . . . . . . . . . . . . . . 12
8. Start-up . . . . . . . . . . . . . . . . . . . . . . . . 12
8.1 Prepare the appliance . . . . . . . . . . . 12
9. Circuit diagram . . . . . . . . . . . . . . . . . . 16
9.1 Descriptions . . . . . . . . . . . . . . . . . . 17
9.2 Connection colours . . . . . . . . . . . . 17
Use
10. Chemical preparation . . . . . . . . . . . . . 18
11. Instructions for use . . . . . . . . . . . . . . . 19
11.1 Film insertion without adapter . . . . 19
11.2 Film insertion with adapter . . . . . . . 21
11.3 Miscellaneous . . . . . . . . . . . . . . . . 24
12. Maintenance . . . . . . . . . . . . . . . . . . . . 25
12.1 Twice weekly change water
and check level of chemicals. . . . . 25
12.2 Every 3 weeks change chemicals . 27
12.3 Every 6 months clean the film
transport . . . . . . . . . . . . . . . . . . . . 29

EN
42016/01SE
Important
Information
1. Warnings and Symbols
Warnings
The warning notes in this document are desi-
gned to point out possible hazards which could
cause either injury to staff or damage to the
appliance.
They are marked using the following warning
symbols:
General warning symbols
Warning - dangerous electrical voltage
The safety instructions are laid out in the
following way:
SIGNAL WORD
Description of type and cause of
hazard
Description of possible outcomes if
safety notes are ignored
• Observe these measures to prevent
any possible danger occuring.
The safety instructions are graded in four levels
of danger:
DANGER Extremely hazardous and
could lead to serious injury
or death
WARNING Possibly hazardous but could
lead to serious injury or death
CAREFUL Could lead to minor injury
ATTENTION Could lead to serious damage
Further symbols used
These symbols are used in this documentation
and /or on the appliance:
Notes, e.g. special instructions concer-
ning efficient usage of the appliance.
Unplug at the mains and remove all
power.
Observe the instruction documentation
supplied
Date of manufacture
Manufacturer
Order no./Model no.
Serial no.
Dispose of this appliance correctly
according to EU directive (2012/19/
EU-WEE).
EC REP Authorised EU representative
CE mark
Handling instructions
Handling instructions are marked with a dot:
• Execute this handling step.

EN
2016/01SE 5
2. General
2.1 Note on Conformity
This product has been tested for conformity
according to the appropriate directives as laid
down by the European Union and has been
found to conform to all the required specifica-
tions.
2.2 General Notes
• These Installation and Operating Instructions
form an integral part of the unit. They must
be kept close to the unit at all times. Precise
observance of these instructions is a pre-
condition for use of the unit for the intended
purpose and for its correct operation.
New personnel must be made aware of the
contents, and they should be passed on to
future operating staff.
• Safety for the operator as well as trouble-
free operation of the unit are only ensured
if use is made of original equipment parts.
Additionally, only parts specifically refer-
red to in these Installation and Operating
Instructions or accessories and disposable
materials specifically recommended by Dürr
Dental may be used. If other accessories or
disposable materials are used with this ap-
pliance, Dürr Dental cannot guarantee safe
operation or proper functioning. No liability on
the part of the manufacturer will be accepted
in the case that damage arises through the
use of non-approved accessories.
• The manufacturer are only responsible for
the equipment with regard to safety, reliabi-
lity and proper functioning where assembly,
resettings, changes or modifications, ex-
tensions and repairs have been carried out
by Dürr Dental or an agency authorized by
Dürr Dental and if the equipment is used in
conformity with the Installation and Operating
Instructions.
• These Installation and Operating Instructions
conform to the relevant version of the equip-
ment and the underlying safety standards
valid at the time of going to press. All circuits,
processes, names, software and appliances
quoted are protected under industrial proper-
ty rights.
• The translation of these Installation and
Operating Instructions has been carried out
in good faith. No liability can be accepted
for mistakes in the translation. The enclosed
German version of these Installation and
Operating Instructions is the reference versi-
on. If there is any doubt about the translation
please consult your dealer.
• Any reprinting of the technical documentation,
in whole or in part, is subject to prior approval
of Dürr Dental being given in writing.
• Retain the packaging for possible return of the
product to the manufacturers. Only the origi-
nal packaging provides adequate protection
during transport of the unit.
Should return of the product to the manuf-
acturers be necessary during the guarantee
period, Dürr Dental accepts no responsibility
for damage occurring during transport where
the original packaging was not used!
Ensure that the packaging is kept out of the
reach of children.
2.3 Qualified personnel
2.3.1 Instructions for use
Persons who operate the units must ensure safe
and correct handling based on their training and
knowledge.
• Instruct or have every user instructed in hand-
ling the unit.
2.3.2 Installation and repair
• Installation, readjustments, alterations, up-
grades and repairs must be carried out by
Dürr Dental or by qualified personnel specifi-
cally approved and authorized by Dürr Dental.
2.4 Disposal
2.4.1 Appliance
• EU directive 2012/19/EU - WEEE (Waste
Electric and Electronic Equipment) of 4th July
2012 and its current implementation state that
under national law Dental Products are cove-
red by the said directive and therefore, within
the European Union, must be disposed of as
special waste.
• If you have any questions at all concerning
the proper disposal of this product, please
contact either Dürr Dental directly or your usu-
al specialist dental trader.
2.4.2 X-ray chemicals
Observe any local or national rules and regulati-
ons concerning disposal of X-ray chemicals.

EN
62016/01SE
2.5 Notes on medical products
• This product is a technical medical appli-
ance and, as such, may only be operated by
such persons who, as a result of training or
experience, can be confidently expected to
operate it correctly and safely for patients and
staff alike.
• Other systems should not be plugged into the
same multi-socket unit.
2.6 Correct Usage
The Periomat Plus is designed for the develop-
ment of intraoral X-ray films of sizes 2 x 3cm to
5,7 x 7,6cm.
2.7 Incorrect usage
Any use of this appliance/these appliances
above and beyond that laid down in the Instal-
lation and Operating Instructions is deemed to
be incorrect usage. The manufacturer cannot
be held liable for any damage resulting from
incorrect usage. The operator will be held liable
and bears all risks.
2.8 Connecting peripheral
appliances
Appliances may only be connected together
or connected to any other assemblies where
complete and utter safety of the patients, opera-
tors and staff and of the environment will not be
affected in any way.
Where any doubts remain concerning the safety
when connecting to other units then the opera-
tor is obliged to ascertain that such connection
can in no way affect the safety of operator,
patient or other staff by referring to the manuf-
acturer or a fully qualified and competent expert.
If the equipment is used in a manner not spezi-
fied by Dürr Dental, the protection offered by the
equipment may be impaired.

EN
2016/01SE 7
3. Safety
3.1 General Safety Notes
This appliance has been so designed and de-
veloped by the manufacturer that under correct
usage that there can be no danger to operator
or patient. In spite of this, we feel it is our duty
to mention the following safety measures in
order to prevent any possible danger.
• When using this appliance all local and rele-
vant regulations must be observed!
Converting or modifying the appliance in any
way is strictly prohibited. In such cases, any
and all guarantees immediately become in-
valid. The operation of modified appliances
can be punishable by law. In the interests of
trouble-free operation the operator is respon-
sible for observing these regulations.
• Installation must be carried out by a technical
expert.
• Before every use the operator must check
the functional safety and the condition of the
appliance.
• The operator must be knowledgeable in the
operation of the appliance.
• The product is not designed to be used in me-
dical treatment areas where the danger of ex-
plosion exists. Areas where explosions could
occur are those where flammable anesthetic
material, skin cleansers, oxygen and skin dis-
infectants are present. This appliance is not to
be used in areas where the atmosphere could
cause fire.
3.2 Electrical safety instructions
• The appliance may only be connected to an
earthed safety socket.
• Before connecting to the electricity supply the
appliance must be inspected and checked
that the supply voltage and the supply fre-
quency correspond to that of the local electri-
cal supply.
• Before initial use and start-up the appliance
and all supply lines must be checked for any
signs of damage. Damaged supply lines and
connections must be replaced immediately.
• Never come into contact with patients and
open plug-in connections on the appliance at
the same time.
• When using the appliance observe all the rele-
vant electrical safety procedures.
• Only use the line cord provided with the unit.

EN
82016/01SE
2
9
6
8
7
15
12
13
10
14
19
18
3
4
111a
5
1 2
3
11b
11c 11d
11

EN
2016/01SE 9
4. Delivery Contents
Model 1307-01 (230V, 50Hz)
Periomat Plus with daylight top, and heating
1 Daylight top . . . . . . . . . . . . . . 1304A710-00
2 Waste container . . . . . . . . . . . . 1303-000-06
3 Protective cover . . . . . . . . . . . . 1307-981-00
4 Cover for loading slot . . . . . . . . 1303-000-05
5 Film transport. . . . . . . . . . . . . . 1307-300-00
6 Water tank . . . . . . . . . . . . . . . . 1307100001
7 Fixer tank. . . . . . . . . . . . . . . . . 1303-000-09
8 Developer tank. . . . . . . . . . . . . 1303-000-08
9 Appliance base . . . . . . . . . . . . 1307100002
10 Periomat Intra/C,
X-ray chemicals . . . . . . . . . . CXB210C9940
11 Adapter for films,
11a 2 x 3,5 cm, 2 x 3 cm (3x) . 1303-000-01
11b 2,4 x 4 cm (3x) . . . . . . . . . 1303-000-18
11c 5,7 x 7,6 cm (1x) . . . . . . . 1303-000-22
11d 4 x 5 cm and 2,7 x 5,4 cm
(ea 1x) . . . . . . . . . . . . . . . 1303-000-02
12 Film collector . . . . . . . . . . . . . . 1303-001-00
13 Drip pan. . . . . . . . . . . . . . . . . . 1303-000-13
14 Sponges grey (2 x) . . . . . . . . . 1330-000-06
Sponge red (1 x) . . . . . . . . . . . 1330-000-05
15 Light protection hood for
loading slot . . . . . . . . . . . . . . 1303A000-14
- Operating Instructions . . . . . 1307100003L..
4.1 Special accessories
The parts listed as special accessories
are not part of the standard scope of
delivery but can be ordered separately.
18 Perioclean-Set
for film transport cleaning . . . . . 1304-070-00
19 Container, double tray . . . . . . . 1303-000-16
4.2 Disposable materials
10 Periomat Intra/C,
X-ray chemicals . . . . . . . . . . CXB210C9940
20 Periomat Intra,
X-ray chemicals . . . . . . . . . . CXB200C9940
21 Universal Cleaner,
Double pack . . . . . . . . . . . . CCB610A5540
22 WR 2000 Spray cleaner,
Six pack. . . . . . . . . . . . . . . . CCB800C5540
20
4
21
22
10

EN
10 2016/01SE
5. Technical Data
5.1 Model Overview
Model 1307-01 (230V, 50Hz)
Periomat Plus with daylight top, and heating
Model 1307-01
Voltage VAC 230
Frequency Hz 50
Rated current A 1,8
Rated power W 400
Duty cycle %ED 100
Film processing
time min 5
Developing
temperature °C 25
Warm-up time min /
°C
~7
Heating V 24
Appliance fuse AH T 2,5
Volume
D eveloper-
tank l 1
Fixer tank l 1
Water tank l 1,2
Weight kg 11,2
Dimensions
(HxBxT)
cm 40 x 63 x 25
Classification Medical products class I
Manufacturer Air Techniques for Dürr
Dental, 1295 Walt Whitman
Road, Melville, New York
11747, USA
Authorised EU
representative
MDSS GmbH, Schiffgra-
ben 41, 30175 Hannover,
Germany
5.2 Model identification plate
The model identification plate can be found on
the rear side of the appliance under the protec-
tive cover.
5
6
2016
X000100
Made in USA
Manufactured for
DÜRR DENTAL AG
MDSS GmbH
Schiffgraben 41
30175 Hannover, Germany
REP
EC
Air Techniques
1295 Walt Whitman Road
Melville, New York 11747
2X T 2,5 AH 250V (IEC 60127-2)
AC 230V 50 Hz 1,8A
1/N/PE
!
SN
Periomat Plus
1307-01
REF

EN
2016/01SE 11
5.3 Ambient conditions
Ambient conditions for storage and
transport
Temperature (°C). . . . . . . . . . . . . -10 up to +60
Rel. humidity (%) . . . . . . . . . . . . . . . . . . max. 95
Ambient conditions on operation
Temperature (°C). . . . . . . . . . . . . +10 up to +25
Rel. humidity (%) . . . . . . . . . . . . . . . . . . max. 80
6. Switch panel functions
The yellow and green switches are fitted with an
integrated control lamp.
Yellow main power supply (23)
Pos. O: Periomat Plus OFF
Pos. l: Periomat Plus ON
Green transport schwitch (24)
Pos. O: Transport motor OFF
Pos. l: Transport motor ON,
Developer process starts up
7
23
24

EN
12 2016/01SE
Mounting
7. Set-up
7.1 Room for Set-up
Max. Ambient temperature 25°C.
Never use the Periomat in a position
with direct sunlight!
The film material may become expo-
sed despite the use of the daylight
top.
• Set up the Periomat in a dry, well ventilated
room.
• The mains supply socket should be so laid out
that the main appliance plug is clearly visible,
and is easily accessible.
7.2 Set-up
• Take the Periomat out of its carton.
• Set the appliance up on a stable and hori-
zontal surface in the vicinity of a mains supply
socket.
8. Start-up
8.1 Prepare the appliance
• Remove the protective cover.
• Remove the box containing the adapter.
• Remove the transportation safety padding
material (foam rubber and cardboard in dryer
compartments)!
• Remove the film transport (5).
• Remove the sponges from the tanks.
• Swivel the temperature controller (25)
upwards.
• Remove the developer tank (8), fixer tank (7)
and water tank (6), and remove any traces of
packing material.
8
5
25
8
7
6
9
10

EN
2016/01SE 13
• Replace the parts in position.
• Place the protective cover (3) in position.
• Place the cover (4) onto the loading slot (slot 8
must face to the front).
• Hang the film collector (12) in position.
11
4
5
12
12
4
3

EN
14 2016/01SE
• Check that the local supply voltage of the
mains supply socket is identical to the voltage
information on the model identification plate of
the appliance.
CAREFUL
Danger of a short circuit due to con-
densated water coming into contact
with the electronic circuit board!
• Only connect and operate the appli-
ance after allowing it to warm up to
room temperature after transport.
• Plug in at the mains.
• Switch on the appliance at the yellow switch
(23).
The developer and fixer tanks are loca-
ted on a temperature regulated heating
plate.
If the temperature level when filling is
lower than 25°C then, after switching
on at the yellow main power switch, the
chemicals will automatically be heated
up and kept to a constant temperature.
Example:
Warm up time 7 min per °C.
The optimum developer temperature is 25°C.
Assuming an initial temperature of 18°C, the
warm up time will be approximately 45 min.,
until the ideal developer temperature has been
reached.
The green transport switch (24) lights as soon
as the set developer temperature of 25°C has
been reached.
24
23
13
14
3

EN
2016/01SE 15

EN
16 2016/01SE
9. Circuit diagram

EN
2016/01SE 17
9.1 Descriptions
1 Yellow main power supply
2 Green transport switch
3 Transformer unit
4 Electronics
5 Temperature sensing device
6 Bath heating
7 Plug
8 Ventilation fan for film drying
9 Distributor 1
10 Distributor 2
11 Transport motor
12 Fuse controller
13 Fuse power supply
14 Heating for film drying
15 Thermal fuse
9.2 Connection colours
gn/ge = green/yellow
rt/sw = red/black
ws/or = white/orange
sw = black
rt = red
br = brown
bl = blue
or = orange
gn = green

EN
18 2016/01SE
Use
10. Chemical preparation
In order to produce perfect developer
results we recommend you use the
specially designed Dürr Periomat Intra/C
Chemicals.
ATTENTION
Danger of liquid overflowing!
Defect in the heater plate.
• If liquid overflows, remove the heater
plate and wipe dry, see 12.2
Film quality insufficient due to
mixing of chemicals.
• After filling with the chemicals, do not
move the Periomat.
• Switch off the appliance at the yellow main
power switch.
• Unplug at the mains and remove all power.
• Remove the protective cover.
• Fill up the water tank with max. 25°C warm
water to max. 1,2 l (6).
• Place the black developer tank in position (8).
• Fill developer (black bottle) into the black de-
veloper tank (8).
• Swivel the temperature controller (25)
downwards.
• Fill fixer (red bottle) into the red fixer tank (7)
and place tank in position.
• Pour warm water at max. 25°C into the red
fixer tank (7) and into the black developer tank
(8) to the lower markings.
• Stir the developer and fixer well.
This serves to avoid differences in quality of
the film development results.
• Place the film transport (5) carefully into po-
sition. Be careful to avoid any splashing or
spilling of chemicals.
6
8
25
8
7
16
17
18

EN
2016/01SE 19
11. Instructions for use
Films of format 3 x 4 cm are placed into the
loading slot without adapter, see 11.1.
Films of larger formats are first placed in the ap-
propriate adapter before insertion in the loading
slot, see 11.2.
11.1 Film insertion without adapter
• Switch on the appliance at the green transport
switch (24).
• The green transport switch (24) lights up when
the appointed development temperature of
25°C is achieved.
• Insert 3 x 4 cm films in the numbered cover
(4) of the 8-slot loading slot. Only insert one
film into each slot.
• Place the light protective cover (15) in
position.
• Slide the start lever (27) to the right.
A new film can only be inserted once
the start lever (27) is back in its starting
position (after ca. 50seconds).
24
4
15
27
19
20
21

EN
20 2016/01SE
• After film development the 3 x 4 cm films fall
into the film collector (12) between the guiding
ridges (28).
• Once the films are in the film collector, switch
off at the green transport switch (24).
• At the end of surgery hours or before a longer
break, e.g. midday break, switch the appli-
ance off at the yellow main power switch (23).
24
12
28
22
23
24
23
8
11.1.1 Speedy developing for
root canal treatment
• When carrying out root canal treatment place
the film in the first slot, 8.
• After ca. 2:30 min. switch off the appliance at
the yellow power supply switch (23).
• Open the front flap and using a suitable instru-
ment, e.g. a pair of tweezers, remove the film
carefully from film slot 8.
These films cannot be archived as they
have not completed the full cycle inclu-
ding water treatment.
In order that the exposure can be added
to the archives it is necessary that the
film material goes through a complete
film development cycle again.