Durr Dental Power Tower View User manual

EN
Power Tower View
Installation and operating instructions
A949100052L02
*A949100052L02*
2104V003

Contents
Important information
1About this document .. . . . . . . . . . . . . 3
1.1 Warnings and symbols .. . . . . . . 3
1.2 Copyright information .. . . . . . . . 4
2 Safety .. . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1 General safety information .. . . . . 4
2.2 Specialist personnel .. . . . . . . . . 4
2.3 Electrical safety .. . . . . . . . . . . . . 5
2.4 Only use original parts .. . . . . . . . 5
2.5 Transport .. . . . . . . . . . . . . . . . . . 5
2.6 Disposal .. . . . . . . . . . . . . . . . . . 5
Product description
3Overview .. . . . . . . . . . . . . . . . . . . . . . . 6
3.1 Scope of delivery .. . . . . . . . . . . . 6
3.2 Optional items .. . . . . . . . . . . . . . 6
3.3 Wear parts and replacement
parts .. . . . . . . . . . . . . . . . . . . . . 6
4Technical data .. . . . . . . . . . . . . . . . . . . 7
4.1 PTV A949444000 and
A949443000 with second Duo
unit and CA 4 .. . . . . . . . . . . . . . 8
4.2 PTV A949454000 and
A949453000 with second Duo
unit .. . . . . . . . . . . . . . . . . . . . . . 8
4.3 Type plate .. . . . . . . . . . . . . . . . . 9
4.4 Declaration of conformity .. . . . . . 10
5 Operation .. . . . . . . . . . . . . . . . . . . . . . 11
5.1 Wet suction system .. . . . . . . . . . 11
5.2 Dry suction system .. . . . . . . . . . 11
5.3 Functional description .. . . . . . . . 12
5.4 Touch display .. . . . . . . . . . . . . . 12
Assembly
6Requirements .. . . . . . . . . . . . . . . . . . . 13
6.1 Pipe materials .. . . . . . . . . . . . . . 13
6.2 Hose materials .. . . . . . . . . . . . . 13
6.3 Installation and routeing of hoses
and pipes .. . . . . . . . . . . . . . . . . 13
6.4 Information about electrical con-
nections .. . . . . . . . . . . . . . . . . . 13
6.5 Information about connecting
cables .. . . . . . . . . . . . . . . . . . . . 14
7 Installation .. . . . . . . . . . . . . . . . . . . . . . 14
7.1 Combining devices safely .. . . . . 14
7.2 Setting up and connecting the
lower part of the cabinet .. . . . . . 14
7.3 Mounting the upper part of the
cabinet .. . . . . . . . . . . . . . . . . . . 16
7.4 Installing the compressor units .. 16
7.5 Install the drying unit .. . . . . . . . . 17
7.6 Install the amalgam separator
(optional) .. . . . . . . . . . . . . . . . . . 19
7.7 Connecting the unit .. . . . . . . . . . 19
8 Commissioning .. . . . . . . . . . . . . . . . . . 20
8.1 Monitoring the unit via the net-
work .. . . . . . . . . . . . . . . . . . . . . 20
Usage
9Operating the touch screen .. . . . . . . . 22
9.1 Navigating .. . . . . . . . . . . . . . . . . 22
9.2 Using menus .. . . . . . . . . . . . . . . 22
9.3 Calling up messages on the
touch screen .. . . . . . . . . . . . . . . 22
10 Operation .. . . . . . . . . . . . . . . . . . . . . . 23
10.1 Switch on the unit. .. . . . . . . . . . 23
10.2 Device information .. . . . . . . . . . . 23
10.3 Configuring the units .. . . . . . . . . 23
10.4 Amalgam separator .. . . . . . . . . . 23
11 Maintenance .. . . . . . . . . . . . . . . . . . . . 24
11.1 Compressor unit and drying unit .. 24
Contents
A949100052L02 2104V003 1
EN

Troubleshooting
12 Tips for operators and service techni-
cians .. . . . . . . . . . . . . . . . . . . . . . . . . . 26
Appendix
13 Connection media plan .. . . . . . . . . . . 27
14 Electrical connection plan .. . . . . . . . . 28
14.1 Version 400 V, 3N~ .. . . . . . . . . . 28
15 Menu structure .. . . . . . . . . . . . . . . . . . 29
15.1 Settings .. . . . . . . . . . . . . . . . . . . 29
Contents
2 A949100052L02 2104V003
EN

Important information
1 About this document
These installation and operating instructions rep-
resent part of the unit.
If the instructions and information in these
installation and operating instructions are
not followed, Dürr Dental will not be able
to offer any warranty or assume any liabil-
ity for the safe operation and the safe
functioning of the unit.
The German version of the installation and oper-
ating instructions is the original manual. All other
languages are translation of the original manual.
These operating instructions are valid for
Power Tower View, order number: A949444000,
A949443000, A949454000, and A949453000.
1.1 Warnings and symbols
Warnings
The warnings in this document are intended to
draw your attention to possible injury to persons
or damage to machinery.
The following warning symbols are used:
General warning symbol
Warning – dangerous high voltage
The warnings are structured as follows:
SIGNAL WORD
Description of the type and source of
danger
Here you will find the possible conse-
quences of ignoring the warning
❯Follow these measures to avoid the
danger.
The signal word differentiates between four levels
of danger:
–DANGER
Immediate danger of severe injury or death
–WARNING
Possible danger of severe injury or death
–CAUTION
Risk of minor injuries
–NOTICE
Risk of extensive material/property damage
Other symbols
These symbols are used in the document and on
or in the unit:
Note, e.g. specific instructions regarding
efficient and cost-effective use of the unit.
Observe the operating instructions.
CE labelling
Manufacturer
Serial number
Order number
Dispose of correctly in accordance with
EU Directive 2012/19/EU (WEEE).
Dispose of the packaging material in an
environmentally responsible manner.
Wear protective gloves.
Wear protective goggles.
3N
Three phase alternating current with neu-
tral conductor
Disconnect all power from the unit.
Monitor ambient conditions
Important information
A949100052L02 2104V003 3
EN

1.2 Copyright information
All circuits, processes, names, software pro-
grams and units mentioned in this document are
protected by copyright.
The Installation and Operating Instructions must
not be copied or reprinted, neither in full nor in
part, without written authorisation from Dürr Den-
tal.
2 Safety
Dürr Dental has designed and constructed this
unit so that when used properly and for the inten-
ded purpose it does not pose any danger to
people or property.
Despite this, the following residual risks can
remain:
– Personal injury due to incorrect use/misuse
– Personal injury due to mechanical effects
– Personal injury due to electric shock
– Personal injury due to radiation
– Personal injury due to fire
– Personal injury due to thermal effects on skin
– Personal injury due to lack of hygiene, e.g.
infection
2.1 General safety information
❯Always comply with the specifications of all
guidelines, laws, and other rules and regula-
tions applicable at the site of operation for the
operation of this unit.
❯Check the function and condition of the unit
prior to every use.
❯Do not convert or modify the unit.
❯Comply with the specifications of the Installa-
tion and Operating Instructions.
❯The Installation and Operating Instructions
must be accessible to all operators of the unit
at all times.
2.2 Specialist personnel
Operation
Unit operating personnel must ensure safe and
correct handling based on their training and
knowledge.
❯Instruct or have every user instructed in han-
dling the unit.
The following groups are not permitted to
operate or use a commercially operated unit:
– People without the necessary experience and
knowledge
– People with reduced physical, sensory or men-
tal capabilities
– Children
Installation and repairs
❯Installation, readjustments, alterations,
upgrades and repairs must be carried out by
Dürr Dental or by qualified personnel specifi-
cally approved and authorized by Dürr Dental.
Important information
4 A949100052L02 2104V003
EN

2.3 Electrical safety
❯Comply with all the relevant electrical safety
regulations when working on the unit.
❯Never touch the patient and unshielded plug
connections on the device at the same time.
❯Replace any damaged cables or plugs immedi-
ately.
2.4 Only use original parts
❯Only use accessories and optional items that
have been recommended or specifically
approved by Dürr Dental.
❯Only use only original wear parts and replace-
ment parts.
2.5 Transport
The original packaging provides optimum protec-
tion for the unit during transport.
If required, original packaging for the unit can be
ordered from Dürr Dental.
Dürr Dental will not accept any responsi-
bility or liability for damage occurring dur-
ing transport due to the use of incorrect
packaging, even where the unit is still
under guarantee.
❯Only transport the unit in its original packaging.
❯Keep the packing materials out of the reach of
children.
2.6 Disposal
The unit must be disposed of properly.
Within the European Union, the unit must
be disposed of in accordance with EU
Directive 2012/19/EU (WEEE).
❯If you have any questions about the correct
disposal of parts, please contact your dental
trade supplier.
The unit may be contaminated. Instruct
the company disposing of the waste to
take the relevant safety precautions.
❯Decontaminate potentially contaminated parts
before disposing of them.
An overview of the waste keys for Dürr
Dental products can be found in the
download area at:
www.duerrdental.com
Document no.: P007100155
Important information
A949100052L02 2104V003 5
EN

Product description
3 Overview
3.1 Scope of delivery
The following items are included in the scope of
delivery (possible variations due to country-spe-
cific requirements and/or import regulations):
Power Tower View .. . . . . . . . . . . . . A949444000
– Basic unit
– 400 V electronics box
– 400 V VS 1200 S
– 400 V Duo unit
– 20 l pressure tank
– Universal membrane dryer
– OroCup Care system
Power Tower View .. . . . . . . . . . . . . A949443000
– Basic unit
– 400 V electronics box
– 400 V VS 900 S
– 400 V Duo unit
– 20 l pressure tank
– Universal membrane dryer
– OroCup Care system
Power Tower View .. . . . . . . . . . . . . A949454000
– Basic unit
– 400 V electronics box
– 400 V V 1200 S
– 400 V Duo unit
– 20 l pressure tank
– Universal membrane dryer
Power Tower View .. . . . . . . . . . . . . A949453000
– Basic unit
– 400 V electronics box
– 400 V V 900 S
– 400 V Duo unit
– 20 l pressure tank
– Universal membrane dryer
3.2 Optional items
The following optional items can be used with the
device:
Pressure reducer .. . . . . . . . . . . . . . 6040-992-00
Amalgam separator .. . . . . . . . . . . . 7805-100-50
Compressor unit .. . . . . . . . . . . . . . A949300060
3.3 Wear parts and replacement
parts
The following working parts must be replaced at
regular intervals (refer also to "Maintenance");
these articles do not bear the CE mark:
Air intake filter .. . . . . . . . . . . . . . . . 0832-982-00
Fine filter .. . . . . . . . . . . . . . . . . . . . 1610-121-00
Virus bacteria filter .. . . . . . . . . . . . . 1650100172
Sintered filter .. . . . . . . . . . . . . . . . . 1650-101-00
To configure the required filters or filter
sets, you can also use our filter configura-
tor at:
www.duerrdental.com/filterkonfigurator
Any repairs exceeding routine mainte-
nance may only be carried out by quali-
fied personnel or our service.
Information about replacement parts is
available from the portal for authorised
specialist dealers at:
www.duerrdental.net
Product description
6 A949100052L02 2104V003
EN

4 Technical data
Electrical data
Rated voltage V 400, 3N~
Frequency Hz 50
Protection class I
Type of protection IP 20
General technical data
Dimensions (W x H x D) mm 640 x 2080 x 610
Pressure tank volume l 20
Delivery at 5 bar (0.5 MPa) l/min 100
Pressure dew point at 7 bar (0.7 MPa) * °C <5
Safety valve settings, maximum permitted
operating pressure
MPa 1
Minimum start-up pressure MPa 0.5
Maximum cut-off pressure MPa 0.9
Noise level ** dB(A) 55
Noise level *** dB(A) 53
* Value determined at an ambient temperature of +40°C
** At an ambient temperature of +40 °C, noise level in accordance with ISO 3744
*** At an ambient temperature of +35 °C, noise level in accordance with ISO 3744
Current reduction without optional items
Current reduction without CA 4 amalgam
separator
A -0.2
Current reduction without second Duo unit A -2.5
Connections
Vacuum connection (external) mm Æ50
Exhaust air connection (external) mm Æ50
Waste connections (DürrConnect) mm Æ20
Compressor connection
Lockable coupling mm 7.2
Network connection
LAN technology Ethernet
Standard IEEE 802.3u
Data rate Mbit/s 100
Connector RJ45
Type of connection Auto MDI-X
Product description
A949100052L02 2104V003 7
EN

Network connection
Cable type ³CAT5
CAN bus
Connector RJ45
Cable type ³CAT5
Ambient conditions during storage and transport
Temperature °C -25 to +55
Relative humidity % 95
Ambient conditions during operation
Temperature °C +10 to +40
Relative humidity % 70
Height above sea level m < 2000
4.1 PTV A949444000 and A949443000 with second Duo unit and CA 4
General technical data
Weight kg 275
Operating mode S1
Delivery at 5 bar (0.5 MPa) l/min 195
Electrical data
Nominal current at 10 bar (1.0 MPa) A 9.0
4.2 PTV A949454000 and A949453000 with second Duo unit
General technical data
Weight kg 265
Operating mode S1
Delivery at 5 bar (0.5 MPa) l/min 195
Electrical data
Nominal current at 10 bar (1.0 MPa) A 8.8
Product description
8 A949100052L02 2104V003
EN

4.3 Type plate
The type plate is located at the bottom right of
the housing.
Product description
A949100052L02 2104V003 9
EN

4.4 Declaration of conformity
Name of manufacturer: DÜRR DENTAL SE
Address of manufacturer: Höpfigheimer Str. 17
74321 Bietigheim-Bissingen
Germany
Name of product: Power Tower View
We hereby declare that the above product meets all applicable requirements of the directives listed
below:
– Machinery directive 2006/42/EC in its current version.
Name of the person with responsibility for compiling all technical documentation:
F. Hatzfeld (Head of Research and Development).
The address is identical to the address of the manufacturer.
– Low voltage guideline 2014/35/EU in its valid version.
– Electromagnetic Compatibility (EMC) Directive 2014/30/EU in its current version.
– Directive 2011/65/EU on the restriction of the use of certain hazardous substances in electrical and
electronic equipment in its current version.
Power Tower View REF A949444000
REF A949443000
REF A949454000
REF A949453000
J. Gramann on behalf of Dürr Dental O. Lange on behalf of Duerr Dental
Head of Research and Development Head of Quality Management
Product description
10 A949100052L02 2104V003
EN

5 Operation
5.1 Wet suction system
2
3
1
4
5
6
7
1 Main power switch
2 Drying unit
3 Suction unit
4 Pressure equalisation tank
5 Compressor unit
6 Pressure tank
7 Touch display
5.2 Dry suction system
2
3
1
4
5
6
7
1 Main power switch
2 Drying unit
3 Suction unit
4 Condensation separator
5 Compressor unit
6 Pressure tank
7 Touch display
Product description
A949100052L02 2104V003 11
EN

5.3 Functional description
The Power Tower View combines compressed air
generation, suction and amalgam separation in
one housing. The housing is insulated, ensuring
an appropriate level of soundproofing. The unit is
operated via a touch display and indicates the
various parameters of the individual components.
5.4 Touch display
1 2
1 Touch display
2 Main power switch
The touch display shows unit data, operating sta-
tuses and messages, and user-dependent unit
settings can be configured.
Product description
12 A949100052L02 2104V003
EN

Assembly
Only qualified specialists or employees
trained by Dürr Dental are permitted to
install, connect and start using the unit.
6 Requirements
Further information can be found in our
suction planning information leaflet.
Order number9000-617-03/..
The room chosen for installation must satisfy the
following requirements:
– Closed, dry, well-ventilated room
– It should not be a room made for another pur-
pose (e.g. boiler room or wet cell).
– Set up the unit on a clean, level and sufficiently
stable surface (take the weight of the unit into
account).
– Set up the units so that the type plate can be
easily read and the unit is easily accessible for
operation and maintenance.
– Leave sufficient distance from any wall (at least
20 cm).
– Refer to the requirements for environmental
conditions in "4 Technical data".
6.1 Pipe materials
Only use vacuum-sealed HT-waste pipes
manufactured from the following materials:
– Polypropylene (PP),
– Chlorinated polyvinyl chloride (PVC-C),
– Plasticizer-free polyvinyl chloride (PVC-U),
– Polyethylene (PE).
The following materials must not be used:
– Acrylonitrile-butadiene-styrene (ABS),
– Styrene copolymer blends (e.g. SAN + PVC).
6.2 Hose materials
For waste connections and suction lines only
use the following hose types:
– Flexible spiral hoses made of PVC with inte-
grated spiral or equivalent hoses
– Hoses that are resistant to dental disinfectants
and chemicals
Plastic hoses will display signs of ageing
over time. Therefore, they should be
inspected regularly and replaced as nec-
essary.
The following types of hoses must not be
used:
– Rubber hoses
– Hoses made completely of PVC
– Hoses that are not sufficiently flexible
6.3 Installation and routeing of
hoses and pipes
❯Execute the on-site pipe installation in accord-
ance with the applicable local regulations and
standards.
❯Lay the hose installation of the drains to or
from the unit at a sufficient incline.
If incorrectly laid, the hoses can
become blocked with sedimentation.
6.4 Information about electrical
connections
❯Ensure that the electrical connections to the
mains power supply are established in accord-
ance with current valid national and local regu-
lations and standards governing the installation
of low voltage units in medical facilities.
❯The connection to the mains supply must be a
fixed connection that cannot be disconnected
without the use of tools. Plug-in connections
(power outlet/plug) are not permissible.
❯Install an all-pole disconnection unit (all-pole
switch) in the electrical connection to the mains
power supply. This must include the clearance
and creepage distances defined in
IEC 61058-1 for a mains voltage peak of 4 kV.
It must be possible to secure the disconnect
switch so that it cannot be inadvertently
switched back on again.
The disconnection unit (switch) must be
easily accessible without danger.
❯Observe the current consumption of the devi-
ces that are to be connected.
Electrical fusing
LS switch 16 A, characteristic C and D in
accordance with IEC 60898.
Assembly
A949100052L02 2104V003 13
EN

6.5 Information about connecting
cables
The diameter of the connections depends on the
current consumption, length of line and the ambi-
ent temperature of the unit. Information concern-
ing the current consumption can be found in the
Technical Data supplied with the particular unit to
be connected.
The following table lists the minimum diameters
of the connections in relation to the current con-
sumption:
Current consumption of
unit [A]
Cross-section
[mm2]
> 10 and < 16 1.5
> 16 and < 25 2.5
> 25 and < 32 4
> 32 and < 40 6
> 40 and < 50 10
> 50 and < 63 16
Control cable
24 V protective low voltage for:
– Hose manifold
– Place selection valve
– Spittoon valve
Installation type Line layout (minimum
requirements)
Fixed installation – Shielded sheathed cable
(e.g. (N)YM (St)-J)
Flexible – PVC data cable with
shielded cable sheath-
ing, as used for tele-
communications and IT
processing systems
(e.g. type LiYCY)
or
– Lightweight PVC control
cable with shielded
cable sheathing
7 Installation
7.1 Combining devices safely
Take care when connecting units together or to
parts of other systems as there is always an ele-
ment of risk (e.g. due to leakage currents).
❯Only connect units when there can be no
question of danger to operator or to patient.
❯Only connect units when it is safe to do so and
when there is no risk of damage or harm to the
surroundings.
❯If it is not 100% clear from the unit data sheet
that such connections can be safely made or if
you are in any doubt, always get a suitably
qualified person (e.g. the manufacturer) to ver-
ify that the setup is safe.
7.2 Setting up and connecting
the lower part of the cabinet
❯Set up the lower part of the cabinet.
❯Connect the exhaust air hose and suction
hose.
❯Remove the transport protection.
❯Attach the cover at the rear.
Assembly
14 A949100052L02 2104V003
EN

❯Connect the exhaust air hose and suction hose
to the floor connection.
❯Place the unit in the correct position and align.
Observe planning template 9000-619-09.
≤100
200
Assembly
A949100052L02 2104V003 15
EN

7.3 Mounting the upper part of
the cabinet
❯Mount the compressed air module on the suc-
tion module using four screws.
7.4 Installing the compressor
units
CAUTION
Functional disorder in case of incor-
rect installation
Unit does not start up.
❯When retrofitting a compressor unit,
the compressor unit must have a star
connection.
❯Mount the pressure tank.
❯Position the compressor unit in the unit.
❯Mount the compressor unit on the retaining
plate using four nuts.
❯Also mount the second compressor unit
(optional) on the retaining plate.
❯Fix the grounding cable.
❯Push on and secure the noise insulation on the
suction manifold of the compressor unit.
❯Position the second compressor unit.
Assembly
16 A949100052L02 2104V003
EN

❯Push on and secure the noise insulation on the
suction manifold of the compressor unit.
7.5 Install the drying unit
❯Install the drying unit.
1
2
❯Insert nozzle, see installation instructions
9000-610-49/01. Insert the filter and close the
drying unit with the cover.
1
2
Assembly
A949100052L02 2104V003 17
EN

❯Connect the drying unit to the compressed air
hose coming out of the cooler.
❯Connect the drying unit to the pressure tank.
Assembly
18 A949100052L02 2104V003
EN