Dynamix UM-A Plus User manual

DYNAMIX UM-A Plus
1Port ADSL2/2+ Router
Quick Start Guide
for ANNEX A/B

1 Port ADSL2/2+ Router 0
C
Co on nt te en nt ts s
1. Panel Descriptions ...............................................................................................1
2. Connecting 1 Port ADSL2/2+ Router .................................................................. 3
3. Setting up the TCP/IP in Windows ...................................................................... 5
Windows ME/98 .................................................................................................... 5
Windows 2000 ......................................................................................................6
Windows XP .........................................................................................................7
4. Setting up the 1 Port ADSL2/2+ Router .............................................................. 8
5. Making sure of Internet connection .................................................................... 20

1
1. . P Pa an ne el l D De es sc cr ri ip pt ti io on ns s
1.1 Back Panel:
The back panel of the 1 Port ADSL2/2+ Router contains ADSL, Ethernet Switches, Reset
Button and Power Adaptor connection.
ADSL Port for connecting to the ADSL/ADSL2/ADSL2+ Service Provider.
LAN 10/100Mbps Ethernet Ports for connecting to the network devices
RESET Restore the 1 Port ADSL2/2+ Router to factory default setting.
POWER 12V DC/1A or 9V AC/1A Power adapter connector.
RESET Button:
Reboot & Restore the 1 Ports ADSL2/2+ Router to factory defaults.
!
To Reset the 1 Port ADSL2/2+ Router:
Ensure that the device is powered on.
Press the Reset button for 10~15 seconds and release. Wait for 30 seconds after
release the Reset button. Do not power off the device during the reset process.
The default settings are now restored after 30 seconds.
1 Port ADSL2/2+ Router 1

1 Port ADSL2/2+ Router 2
1.2 Front Panel:
The 1 Port ADSL2/2+ Router’s LED indicators display information about the device’s status.
PWR Lights up when 1 Port ADSL2/2+ Router is powered on.
LINK/ACT Blinking when 1 Port ADSL2/2+ Router is Sending/Receiving data.
Blinking when 1 Port ADSL2/2+ Router is ready.
ADSL Lights up when a successful ADSL2/2+ connection is established.
READY Lights up when a PPP connection is established.

2
2. . C Co on nn ne ec ct ti in ng g 1 1 P Po or rt t A AD DS SL L2 2/ /2 2+ + R Ro ou ut te er r
2.1 Connection Mechanism:
This section describes the hardware connection mechanism of your 1 Port ADSL2/2+
Router on your Local Area Network (LAN) connect to the Internet, how to configure your 1
Port ADSL2/2+ Router for Internet access or how to manually configure your Internet
connection.
Before you can establish an Internet or Wireless connection through your 1 Port ADSL2/2+
Router, make sure you have the following:
1. A Computer/Notebook with an installed Ethernet Adaptor and an Ethernet Cable.
2. ADSL service account and configuration information provided by your Internet Service
Provider (ISP). The following configuration parameters are require in order to connect
your 1 Port ADSL2/2+ Router to the Internet:
a. VPI/VCI parameters
b. Multiplexing Method
c. Host and Domain Names
d. ISP Login Name and Password
e. ISP Domain Name Server (DNS) Address
f. Fixed or Static IP Address
1 Port ADSL2/2+ Router 3

1 Port ADSL2/2+ Router 4
2.2 Steps for Connection:
Following are the steps to properly connect your 1 Port ADSL2/2+ Router:
1. Turn off your computer.
2. Connect the ADSL port of your 1 Port ADSL2/2+ Router to the wall jack of the ADSL
Line with a RJ-11 cable.
3. Connect the Ethernet cable (RJ-45) from your 1 Port ADSL2/2+ Router to the Ethernet
Adaptor in your computer.
4. Connect the Power adaptor to the 1 Port ADSL2/2+ Router and plug the other end into a
Power outlet.
The Power light will lit after turning on the 1 Ports ADSL2/2+ Router.
Auto and self-diagnostic process might turn the LED indicators ON and
OFF during the process.
!
5. Turn on your computer.
6. Refer to the next chapter to setup or configure your system’s Network Adaptor.

3
3. . S Se et tt ti in ng g u up p t th he e T TC CP P/ /I IP P
Windows Me / 98
Step 1: Click Start→Settings→Control Panel.
Step 2:Double-click the Network icon.
Step 4: Go to IP Address icon and select
Obtain an IP address.
Step 3: Go to Configuration icon, select network
adapter installed and click Properties.
Step 5: Go to Gateway icon and erase all
previous setting.
Step 6: Go to DNS Configuration icon, select
Disable DNS and click OK.
1
2
1
2
1 Port ADSL2/2+ Router 5

Windows 2000
1 Port ADSL2/2+ Router 6
Step 1: Click Start→Settings→Control Panel. Step 4:Select Internet Protocol (TCP/IP) and
click Properties.
Step 2:Double-click the Network and Dial-up
Connections.
Step 5:Select Obtain an IP address
automatically and DNS server address
automatically. Then, click OK.
Step 3: Right Click the Local Area Connection and
select Properties.
2
1
1
2
3
1
2

1 Port ADSL2/2+ Router 7
Windows XP
Step 1: Click Start→Control Panel→Classic View. Step 4:Go to General icon, select Internet
Protocol (TCP/IP) and click Properties.
Step 2: Double-click the Network Connections.
Step 5:Go to General icon, select Obtain an IP
address automatically and DNS server
address automatically.
Then, click OK.
Step 3: Right Click on the Local Area Connection
and select Properties.
1
2
1
3
1
2
2

1 Port ADSL2/2+ Router 8
4
4. . S Se et tt ti in ng g u up p t th he e 1 1 P Po or rt t A AD DS SL L2 2/ /2 2+ + R Ro ou ut te er r
1. Launch your web browser, and enter the 1 Port ADSL2/2+ Router’s IP Address:
“192.168.1.1” in the address field then press the “Enter” key to login.
2. Enter the default User Name: “Admin” and Password: “Admin”. Then press “OK” to
login.
Note that the Username and Password are case sensitive.
!

3. Upon entering the address into the web browser, the configurable HOME page with all
the device configuration information will pop up.
1 Port ADSL2/2+ Router 9

4. Click “EZ SETUP -- Wizard” and proceed with the following steps to help you install the
1 Port ADSL2/2+ Router quickly and easily.
1 Port ADSL2/2+ Router 10

1 Port ADSL2/2+ Router 11
Step 1 Select your country from the list and note the “Encapsulation” type. The
“Encapsulation” type differs in each country and there are two different kinds of
setup windows wizard that will pop-up.
Click “Config” or “CONFIG – New Connection” if you can’t find any
available parameters from the presetting country list.
Check your ISP immediately for the setting/configuration details.
!

A. For countries with the following “Encapsulation” after clicking the “Next” button, you
will enter into “Set PPP Password” window as shown below.
;PPPoA VC-Mux
;PPPoA LLC
;PPPoE LLC
Manually enter your “Username” and “Password” which will be provided by your Service
Provider (ISP). Check this with your ISP for correct settings. Click “Apply” after setup.
1 Port ADSL2/2+ Router 12

B. For countries with the following “Encapsulation” after clicking the “Next” button from
STEP 1, you will enter into the “Set Area” window as shown below.
;1483 Bridged LLC
;1483 Routed VC-MUX
In this current window, you will find 3 Connection Type:
I. Static (Fixed IP by ISP),
II. DHCP (Get IP dynamically from ISP),
III. Bridge.
1 Port ADSL2/2+ Router 13

I. Static (Fixed IP by ISP): Click the radio button to enable Static (Fixed IP by ISP)
option, then click “Next”. The following window will pop-up:
Manually enter the “IP Address”,“Mask”, “Default Gateway” and “DNS”. Click
“Apply” after your setting. Refer to your ISP for further details on the correct setting.
1 Port ADSL2/2+ Router 14

II. DHCP (Get IP dynamically from ISP): Click the radio button to enable DHCP (Get IP
dynamically from ISP) option, then click “Next”. The following window will pop-up:
Click to enable the “Default Gateway” then click “Apply” after your setting. Refer to
your ISP for further details on the correct setting.
1 Port ADSL2/2+ Router 15

III. Bridge: Click the radio button to enable DHCP (Get IP dynamically from ISP) option,
then click “Next”. The following screen will pop-up:
Click and choose “Select LAN” from the dropdown manual or leave it as it’s default
then click “Apply” after your setting. Refer to your ISP for further details on the correct
setting.
1 Port ADSL2/2+ Router 16

1 Port ADSL2/2+ Router 17
Step 2 Click “Apply” after setup. Following windows will pop-up.
The device’s system will reboot and activate your setting after clicking the “Apply” button.

The following windows will pop up after the 1 Port ADSL2/2+ Router’s reboot process.
Check the following items when the above window pop-up. All the setting should
be exactly the same with your setting in STEP1.
;Name: Show the ISP name selected in STEP 1.
;Type: Show the Encapsulation type selected in STEP 1.
;Username: Show the Username manually entered in STEP 1.
;Password: Show the Password manually entered in STEP 1.
;VPI: Show the VPI setting as shown in STEP 1.
;VCI: Show the VCI setting as shown in STEP 1.
A Connection Profile (Normally show the selected ISP Name) will be added to
the left side of the configuration frame under WAN Setup.
NOTE: If the final setting are differ from what you’d selected in STEP 1, click EZ SETUP
and redo the setup procedures or else check your dealer immediately for technical
support.
NOTE: For more detailed information regarding settings and connections, refer to “Users
Manual”.
1 Port ADSL2/2+ Router 18