E-Bench KH 910 Instruction Manual

© graphic design, photos and translations by
ORFGEN · Essen / Germany
www.orfgen-nm.de

Operating instructions
and safety advice Page 5

3D
    
 

4D



5D
OPERATING INSTRUCTIONS KH 910
CONTROLS
Band selector MW / VHF (AM/FM)
Function switch (OFF/ON/AUTO/ALARM)
LED display
Time setting button (TIME SET)
Hours
Minutes
Sleep button
Snooze button
Alarm
Tuner
Volume control
Battery compartment (in event of mains power failure)
SAFETY ADVICE
· Operate the device at the correct mains voltage only (220 / 230 Volt ~ 50 Hz).
· Exposing this type of electrical equipment to high temperatures or moisture could lead to fires or
electric shock. To prolong the service life of your radio do not position it near water or heating
radiators. Always find a place with good air circulation.
· Never use damaged electrical equipment (the device itself or its mains lead).
· Do not try to reach the appliance if it falls into water. Pull out the plug from the mains socket
immediately.
· The electrical components in this device are at high voltage. Never remove any parts of the
housing.
· If repairs are required please take or send the device to our customer services centre (See the
guarantee card for the address and telephone number).
· When required, the housing can be cleaned with a soft cleaning cloth (after ensuring that the plug
is out of the mains socket). Never use cleaning agents as they could damage the housing.
CONNECTING TO MAINS
Insert the plug into a mains socket (make sure the mains voltage matches that of the device).

RADIO RECEPTION
Switch on the radio by moving the function switch into the ON position.Set the band selector
switch to the required position (VHF or MW) . Set the volume using the volume control .
Set the radio to the VHF or medium wave frequency of your choice using the tuner .
AERIALS
FM (VHF): Unwind and position the wire aerial for best reception of VHF
AM /MW: The radio has a sensitive ferrite aerial.
SETTING THE TIME
Press and hold down the TIME button (TIME / TIME-SET) whilst pressing the HOURS or
MINUTES button until you see the correct time in the display.
SETTING THE ALARM TIME
Press the ALARM and HOURS or MINUTES button until the required alarm time appears in
the display.
SETTING THE ALARM MODE
1 First set the required alarm time as explained above.
2 If you wish to be woken by the buzzer set the FUNCTION SWITCH  to ALARM. The activated
alarm mode is then shown in the display.
3 If you wish to be woken by the radio, set the FUNCTION SWITCH  to ON and select the
desired station/frequency and the volume .
4 Then set the FUNCTION SWITCH  to AUTO. The activated alarm mode is then shown in the
display.
The appropriate alarm sounds when the alarm time is reached. The alarm sound switches off
automatically after 1 hour 59 minutes.
6D

7D
The alarm sound can be temporarily interrupted by pressing the SNOOZE button . After
approximately 9 minutes the alarm sound automatically switches itself on again. This process can be
repeated for a maximum of 1 hour 59 minutes. You can cut short the alarm period by setting the
FUNCTION SWITCH  to OFF.
AUTOMATIC 24 HOUR ALARM
After the alarm is switched off, if you set the FUNCTION SWITCH to AUTO again the alarm will
sound on the next day at the same time.
GOING TO SLEEP WITH THE SLEEP FUNCTION
This setting allows you to go to sleep whilst listening to the radio.With the FUNCTION SWITCH in
the AUTO or OFF position the radio plays for a maximum of 1 hour 59 minutes.
1 Press the Sleep button  to set the time for which the radio will play. The display shows .
2 If you wish the radio to stop playing earlier just press and hold down the Sleep button whilst
pressing the MINUTES button until the desired playing time is displayed.
3 If you wish the playing time to be extended to 1:59, press and hold down the Sleep button 
whilst pressing the HOURS button.
4 To switch off the Sleep function or to set the sleep time to press the SNOOZE button .
NOTE: Pressing the Sleep button again after setting the sleep time will automatically reset the
sleep time to . Press the SNOOZE button to switch off the Sleep function.
MAINS POWER FAILURE
To guard against losing your settings in the event of a mains power failure insert a 9-volt battery into
the battery compartment. The battery ensures that the radio alarm clock will function in emergency
mode even during a mains power failure. In these circumstances the LED display  will not be illumi-
nated. Once mains power is restored the correct time will be automatically displayed again.
Note: The alarm, radio and LED  display do not function during battery operation.
0:59
0:00
0:59

– Insert the battery into the battery compartment (see Fig. ).
– Replace the battery annually.
STATEMENT OF CONFORMITY
We, Kompernaß Handelsgesellschaft mbH, Burgstr. 21, D-44867 Bochum, Germany, hereby declare
that this product conforms with the following EC regulations:
EC low voltage regulations, Electromagnetic compatibility, Applicable harmonised standards.
Type/Description: Radio alarm clock KH 910
Bochum, 30.11.2002
Hans Kompernaß
- Managing Director -
8D