Earlex SprayPort Professional 6000 Series Instruction Manual

HV6002/ 6003
OPERA ING INS RUC ION MANUAL
Thank you for purchasing the SprayPort from Earlex Professional 6000 Series.
This highly versatile HVLP System (high volume of air, low pressure painting) can be
used for a wide variety of applications.
BEFORE USE – PLEASE READ HE MANUAL AND SAFE Y INS RUC IONS.
Please retain for future reference.
o register your product visit www.sprayport.com
®

WARNING!
IMPORTANT: ‘WARNING !’ alerts user to a spec fic hazard
Other po nts are adv sory wh ch should be followed for safe use
ALWAYS COMPLY WITH THE SAFETY INSTRUCTIONS SUPPLIED WITH THIS PRODUCT
AND THE MATERIAL BEING USED
Only use the unit as described in this manual. Addional product specific warnin s may be found
throu hout the body of this manual where applicable.
FIRE AND EXPLOSION HAZARD
WARNING! The substances used with this Spray Gun (paints, coan s, solvents, etc.) may contain
dan erous, harmful, explosive or corrosive materials.
WARNING! – Use extreme cauon when sprayin any materials with a flash point lower than 70°F
(21°C). Check the technical specificaons on the paint or coan container before sprayin .
• The Spray Gun must only be used with paints, coan s and solvents that have a flash point suitable
for sprayin . Consult the paint, coan or solvent manufacturer’s instrucons and Safety Data Sheets.
• NEVER spray near a naked flame includin an appliance pilot flame.
• NEVER smoke whilst sprayin .
• DO NOT operate li ht switches or run en ines or similar spark producin products in the spray area
if sprayin solvents.
• DO NOT use any coan s or material containin any Halo enated Hydrocarbon constuent such as
bleach and chlorine.
• Always disconnect unit from mains supply when fillin the paint or coan container.
• Keep the turbine in a well - venlated area.
• Keep the turbine as far removed from the spray area as the air hose will allow especially when
usin solvent based coan s.
EQUIPMENT MISUSE HAZARD
WARNING! The use of any accessory or aachment, other than those recommended in this
instrucon manual, may present a risk of personal injury.
WARNING! Use the Spray Gun for the job it was desi ned for only. Misuse of the Spray Gun will
invalidate the uarantee.
WARNING! If the cordset is dama ed, it must be replaced with the correct Earlex part to avoid a
hazard.
WARNING! To reduce the risk of electric shock do not expose to water. Store indoors.
• NEVER under any circumstances aim the Spray Gun at another person or animal. In the event of an
injury seek expert medical advice immediately.
• NEVER carry the turbine whilst sprayin .
• Always ensure there is adequate venlaon when sprayin .
• Aer each use, thorou hly clean the Spray Gun and rease the Fluid Needle.
• This appliance can be used by persons a ed from 14 years and above and persons with reduced
physical, sensory or mental capabilies or lack of experience and knowled e if they have been iven
supervision or instrucon concernin use of the appliance in a safe way and understand the hazards
involved.
• Use only enuine manufacturer replacement parts.
• Always disconnect the unit from the mains supply before cleanin .
PERSONAL PROTECTIVE EQUIPMENT
WARNING! Noise levels exceed 85dB. Therefore suitable ear protecon must be worn.
• Always wear a suitable protecve mask when sprayin . The use of loves, o les and overalls is also
recommended.
HOT SURFACE
• CAUTION: Outlet of turbine and air hose may become hot durin use. Please allow to cool before removin
air hose.
2

This powerful spray system applies coatings faster than brushing or rolling whilst maintaining a
smooth and accurate finish.
The SprayPort®series is designed for the professional decorator and finisher. The latest
technology and materials combine to deliver a consistently high performance.
The SprayPort®series is simple to set up using quick-connect fixings.
The spray gun delivers a high volume of air via the fluid tip for a precise finish.
The powerful steel turbine incorporates open cell air filters for a continuous and clean air flow.
Air is fed to the gun through the lightweight HyperFlex hose made from Thermo-Vulcanised
Polymer.
The HV6000 series sprays a wide range of paint or coatings with or without dilution.
To achieve the desired results only use good quality paint or coating. Keep in mind that low
temperatures make paint or coating thicker. Therefore use of the Spray Gun is not recommended
below a minimum temperature of 15°C.
IN RODUC ION
TM
TECHNICAL SPECIFICATION
MODEL 6002 6003
Turbine 2 sta e 3 sta e
Motor type Tan enal Tan enal
Volta e 230V 230V
Frequency 50Hz 50Hz
Current 5.0A 5.2A
Air filters Dual removable filters Dual removable filters
Pressure ran psi 4.5 (0.31 bar) psi 5.5 (0.38 bar)
Air flow 90 CFM (2550 l/min) 90 CFM (2550 l/min)
Air Hose
25 (7.6m) vulcanised
polymer
25 (7.6m) vulcanised
polymer
3

SPRAYPOR URBINE UNI
No. Description Part No.
1. Air Filter P2014
2. Cordset C3P
3. Circuit Breaker n/a
4. Power Inlet Connector n/a
5. Power Switch n/a
6. Air Outlet - Hose Attachment n/a
7. Gun Dock P2019
8. 25ft (7.6m) Air Hose N0359
PAR S LIS
4

OPERA ION
• Prepare the spray gun for operation (refer to Spray Gun Instruction Manual supplied separately).
• Plug cordset into turbine unit.
• Attach the nut at the end of the air hose to the air outlet on the turbine ensuring it is screwed on
fully. The connection will be rigid when fitted correctly.
• oin the quick connect hose attachment to the air inlet on the spray gun. Tip: If connection is
tight, loosen the quick connect fitting on the hose by unscrewing a little before connecting to the
gun, then retighten.
• Unpack turbine and check all parts are present (see parts list) and undamaged.
• Prepare surfaces to be sprayed ensuring they are clean, dry and smooth.
• Ensure there is adequate ventilation.
• Mask off all areas not intended for spraying.
PREPARA ION
5

SHU ING DOWN
If leaving your sprayer for less than 1 hour:
• Turn the power off ‘O’ (5).
• Extend the Gun Dock (7).
• Dock the spray gun in the Gun Dock (7).
If leaving your sprayer for more than 1 hour:
• Turn the power off ‘O’ (5) .
• Disconnect the air hose from the gun.
• Clean the gun as detailed in the Spray Gun Operating Instruction Manual.
• Allow the turbine unit to cool before disconnecting the air hose.
• Connect cordset to a grounded outlet.
• Turn the power on ‘|’ (5).
• Familiarize yourself with spraying technique (for detailed instruction on how to operate spray
gun refer to Spray Gun Operating Instruction Manual supplied separately) using waste
cardboard.
• When you are happy with your set-up, commence spraying.
NOTE: Check the turbine unit, filters and the gun are clean and dry before operating.
NEVER leave the turbine unsupervised while plugged in.
6

MAIN ENANCE
Some simple maintenance is required to ensure your SprayPort®continues to perform effectively:
IMPORTANT: Always unplug from the mains ahead of any maintenance.
• Clean/ replace filters.
- Filters will become soiled during use. To remove see diagram below. Clean filters in warm
soapy water.
Check the condition of filter carefully and replace if necessary.
WARNING! Ensure filter is completely dry before installing.
• Cleaning the hose:
- Keep the outer surface of the turbine unit clean by wiping with a damp cloth. Do not submerge
into or flush through with water or any chemical. Regularly check for cracks, leaks and holes.
Replace if necessary.
• Cleaning the unit:
- Keep the outer surface of the turbine unit clean by wiping with a damp cloth. Do not submerge
into water or any chemical.
• Store the unit indoors. Be careful not to twist or trap the cordset.
• No other user serviceable parts.
IMPOR AN :
It is important to regularly check and clean the filters, hose and turbine, paying particular attention
to the air inlets and vents. Failure to do so risks damage to the motor or premature failure.
Servicing and repairs must be carried out by authorized service centres only – contact Earlex
Head Office for details.
7

TROUBLESHOOTING
PROBLEM CAUSE ACTION REQUIRED
Little or no s ray Air inlet blocked Check the condition of the Air Filter (1)
and clean or re lace
Check air inlets, air vents and air hose for
blockages
Turbine has no
ower
No ower at su ly Check the ower su ly
Cable fuse has blown Where a licable check fuse and re lace
if necessary
Circuit Breaker (3) has tri ed Reset the Circuit Breaker (3)
Incorrect or damaged ower cord
set used
Use correct ower cord set. Re lace if
necessary
Worn turbine brushes Re lace brushes at an authorized
service centre
8

INFORMA ION ON HE DISPOSAL OF WAS E ELEC RICAL &
ELEC RONIC EQUIPMEN KNOWN AS WEEE
Please do not dispose of tools with your household waste collected by the
council. It is your responsibility to dispose of this type of waste by handing it
over to a special designated collection point for recovery and recycling.
9
MAINS CONNEC ION
Your unit has been supplied with a cordset. This is identified by the fuse holder in the base of the
plug. Please read the following safety instructions before use.
1. If the cordset is damaged replace with a new cordset. Please contact Earlex customer services
for a replacement cordset.
2.NEVER under any circumstances use the appliance or cordset without the fuse cover fitted.
This is the little cover fixed into the base of plug to hold the fuse in place.
3. If you lose the fuse cover then please contact any electrical dealer for a replacement or ring our
helpline.
4. A replacement fuse must be rated at 13 Amps. This must be manufactured and approved to
BS1362.
5.IF IN ANY DOUB PLEASE CONSUL A QUALIFIED ELEC RICIAN.
WARNING - HlS APPLIANCE MUS BE EAR HED. If you are using an extension lead it must
be a 3 - core type and rated at a minimum of 13 Amps and fully unwound. Do not operate with a cord
rated at less than 13 Amps as this will cause premature failure of the product which is not covered
by the guarantee.

NO ES
10

11
NO ES

© 2014 Earlex Ltd. P2035 04/14
24 Month Guarantee
Earlex issues a 24 month guarantee to the purchaser effective from the date of purchase against
defects in materials or workmanship. This guarantee does not cover abuse, accidental damage,
misuse, normal wear parts, motor brush replacement or spray gun maintenance & clean up.
Guarantee is void if repairs are made or attempted by unauthorised persons. At our option,
Earlex will repair or replace defective parts without charge provided the purchaser return
products prepaid to the nearest authorised service centre or to the factory. Factory returns
must first receive a Return Material Authorisation.
Please call 01483 454666
In other countries please call the company where you originally purchased the product.
Earlex will not be held liable if equipment is not used solely for the purpose it was designed.
Guarantee will become void through improper installation or operation. Any modifications to the
equipment or deviations from the recommended procedures, accidental damage or any related
action that impairs or abuses intended use and care of Earlex equipment will also void guarantee
and liability. In the event of rentals, this guarantee period is restricted to 6 months.
EARLEX WILL ACCEPT NO RESPONSIBILITY FOR THE USE OF THIS PRODUCT IF USED
FOR ANY PURPOSES OTHER THAN THOSE DETAILED HEREIN.
All rights reserved © 2014
PLEASE NO E: We have done all we can to ensure that, when used correctly and in
accordance with these instructions, the unit has a long and fault-free life. We accept no
responsibility for damage caused by the use of incorrect or unsuitable substances, paints or
liquids which have not been thinned correctly or which are not suitable for the surfaces to which
they are applied, health hazards arising from a lack of ventilation when working in confined
spaces or equipment which is faulty due to inadequate cleaning of the components after use. If
in doubt, test a small inconspicuous area first. Always read the manufacturer’s instructions
before use. Neither our guarantee nor the above statement affects your statutory rights.
urbine Design Registration
ECD 002307868-0003
US applied for
China applied for
Spray Gun Design Registration
ECD 002307868-0001
ECD 002307868-0002
US applied for
China applied for
EC Declaration of Conformity
We declare that the units HV6002 & HV6003 conform to:
LVD 2006/95/EC, EN60335-1, EMF EN62233;
EMC 2004/108/EC, EN55014-1, EN55014-2
EN61000-3-2, EN61000-3-3
Earlex Ltd
Opus Park, Moorfield Road, Guildford,Surrey, GU1 1SZ
el: [phone]
Open hours: 08.30 - 17.00 Monday to Thursday and 08.30 - 15.45 Friday
(expecting Bank Holidays).
Email: [email protected] Web: www.earlex.co.uk