Eartec UltraLITE User manual

Warranty
All UltraLITE headsets are warranted against defects in material and/or factory
workmanship for a period of one year from the date of purchase. Standard repairs due to
misuse or wear and tear, as well as replacement parts including but not limited to batteries,
padding, USB cable, etc. are excluded. Shipping is to Eartec at customer’s expense, Eartec
will pay for return ground shipping if the product warranty applies to the repair.
Shipping
Prior to returning your headset for warranty or service you must call Eartec for an RA
(Return Authorization) number: 1 [phone]
www.eartec.com
1.800.399.5994
Communicate in Total Comfort
Full Duplex Wireless System
The UltraLITE
General Service
All repair work will be performed for the cost of replacement parts and return shipping
from the Eartec factory.
Service
Eartec Co Inc
145 Dean Knauss Dr
Narragansett RI 02882
EXCELLENT
PERFORMANCE
Effective range up to
1/4 mile.
WEAR ON LEFT OR
RIGHT EAR
Mic boom swivels 270
degrees.
LITHIUM
BATTERIES
Provide continuous
6 hr operation and are
field replaceable.
DECT
TECHNOLOGY
(DIGITAL ENHANCED
CORDLESS
TELECOMMUNICATION)
Safety
1. To prevent possible hearing damage, do not listen at high volume levels for long periods.
2. Risk of explosion if battery is replaced by an incorrect type, dispose of battery according to
the instruction.
3. Recycle your products
The WEEE logo (shown at right) appears on the product to indicate that this product must
not be disposed of or dumped with your other household wastes. You are liable to dispose of
all your electronic or electrical waste equipment by transporting to an appropriate collection
point for recycling of such hazardous waste.
FCC Radiation Exposure Statement: This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment.
IC Warning:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible
d'en
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or
transmitter.
FCC Notice
This device complies with Part 15 of FCC rules. Operation is subject to the following 2 conditions: (1) This device may not
cause harmful interference, and (2) This device must accept any interference received, including interference that may cause
undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.

SET VOLUME
UltraLITE features 5 volume settings. Select the desired volume by
slowly clicking the UP or DOWN buttons. An audible tone reflects
volume level. A double tone indicates low or max volume has been
reached.
Battery
All UltraLITE headsets are powered by a Lithium Polymer
battery that will operate 6 hours when fully charged.
IMPORTANT
UltraLITE systems include one
headset labeled “MAIN”.
This MAIN headset must be
turned “ON” to link the corresponding REMOTE headsets.
Charging
1) Batteries are charged via the multi-charger.
2) Insert the batteries making sure the contacts are
properly aligned.
3) RED: Charging; GREEN: Fully Charged.
Installation
1) Press the release button located on the bottom of
the battery compartment.
2) Insert the battery into the compartment (arrow
indicates proper direction) and snap door closed.
Operation
Adjusting for Fit & Performance
1) Adjust the headband slides for size as necessary.
2) Position the microphone capsule at one finger’s width from the
corner of your mouth to ensure superior speech recognition and
noise cancellation.
3) “TALK” identifies front of microphone: always have this indicator facing towards your
mouth.
STARTUP
1) Turn ON the MAIN headset, switch is located below battery
compartment. Flashing blue LED on earcup confirms headset is in
search mode.
2) Turn ON the REMOTE headset(s), press the power button located
above volume controls.. Flashing blue LED on earcup confirms
headset is in search mode.
3) Flashing LEDs change to solid blue to indicate that headsets are
connected.
SHUT DOWN
Power OFF the MAIN headset utilizing switch, then PRESS and HOLD the power button on
the Remote headset(s) for 4-5 seconds to turn off.
(Note: Blue LED on headsets indicates pairing mode. When headset blue LED is NOT
illuminated, this does NOT necessarily indicate that the headset is off. Please check
switch on Main headset to ensure that it is in OFF position. The battery will continue
to drain if left in the headset, and the switch is not turned to OFF position.)
MAIN ON/OFF
REMOTE ON/OFF
AutoMute Function
Microphone
mutes
automatically
when boom is
set to “UP”
position.
Boom
swivels over
the top 270
degrees.
Headset can
be worn on
left or right
ear.
To ensure optimum charge level remove battery from headsets
when system not in use.
(Note: Blue LED on headsets indicates pairing mode. When headset blue LED is NOT
illuminated, this does NOT necessarily indicate that the headset is off. Please check
switch on Main headset to ensure that it is in OFF position. The battery will continue
to drain if left in the headset, and the switch is not turned to OFF position.)
Low Indicator
A repetitive beep (every 20 seconds) indicates low
power – battery should be charged or replaced.
Battery Care
Release Button