Eastwood B60 User manual

ABRASIVE MEDIA
BLAST CABINET – B60
INSTRUCTIONS
Item #20557

2Eastwood Technical Assistance: 800.343.9353 >> [e-mail]
The EASTWOOD ABRASIVE MEDIA BLAST CABINET – B60 is specifically designed with heavy-duty components and a quality powder coated finish to provide
years of trouble-free service. It features an LED work lamp for increased visibility and a baffled, flow-through ventilation design with an external vacuum
connection for portable or bolt-on vacuums.
SAFETY INFORMATION
WARNING indicates a hazardous situation which, if not avoided, will result in death or serious injury.
READ INSTRUCTIONS
Thoroughly read and understand this manual before using the Eastwood Abrasive Media Blast Cabinet – B60. Save for future reference.
ELECTRIC SHOCK HAZARD!
• Always plug into a properly grounded outlet.
• Under certain conditions (e.g. atmospheric humidity levels, type of media being used and/or type of media being blasted), the friction
of abrasive blasting may generate static electricity and result in shocking. We recommend grounding the blast cabinet in accordance
with local electrical codes.
• For indoor use only.
HEALTH HAZARD!
• Do not use with sand containing crystalline silica. Exposure to crystalline silica may cause silicosis, a serious lung disease,
cancer, and death.
• Dust generated by the blasting process can contain hazardous materials such as lead, zinc chromate, cadmium, and other toxic
compounds. Always wear a NIOSH-approved breathing apparatus when abrasive blasting.
• Never operate the blast cabinet with the door open. Always make sure the door is securely latched and sealed before operating.
• Never operate the blast cabinet without a properly filtered shop-type, dust collecting vacuum. If dust is seeping out of your
cabinet, stop immediately and replace vacuum filter!
OPERATION WARNINGS!
• Never overload the blast cabinet. Maximum weight capacity of object to be blasted is 132 lbs.
Maximum weight capacity of blast media is 100 lbs.
• Inlet air pressure must not exceed 120 PSI. Excessive air pressure can cause permanent damage to the unit and personal injury.
• Disconnect air supply before making adjustments, changing accessories, or storing the cabinet.
• Never use bottled gas as an air source for this cabinet.
SPECIFICATIONS
• Electrical current requirement (lamp): 120 Volt AC, 60hz; 0.034 amp
• Air supply requirements: 7 CFM @ 90 PSI.
• Internal Dimensions: 36" wide x 24" deep x 23" high.
36.25" 24.25"
58.75"
Always use a clean, dry, regulated air supply.
Moisture and or oil in air supply will cause
clogging of blast media.

A
T
T
D
C
X
F
E
G
L
J
Y
Q
B
P
O
N
I
R
S
H
Z
K
W
M
UV
PP
INCLUDES
Part Description Qty.
ADoor 1
BShelf 1
CCabinet Back Panel 1
DCabinet Top Panel 1
ECabinet Left Side Panel 1
FSwitch Box 1
GLeg 4
HCabinet Front Panel 1
ICabinet Right Side Panel 1
JHopper Back Panel 1
KHopper Front Panel 1
LHopper Side Panel 2
MLatch 2
Part Description Qty.
NHopper Drain Door 1
O Media Suction Tube 1
PHopper Corner Reinforcements 4
Q Shelf Floor Supports 1
RGloves 1
SHose Clamp 2
TDoor Struts 2
USeal Ring 2
V Glove Seat 2
WMedia Blasting Gun 1
XVacuum Baffle 1
YHopper Bottom Frame 1
ZHopper Drain Latch 1
Part Description Qty.
AA M6 x 12mm Screw 118
BB M4 x 16mm Screw 15
CC M4 x 10mm Screw 30
DD M4 x 6mm Screw 2
EE M6 Nut 75
FF M4 Nut 20
GG M4 Flat Washer 35
JJ Thick Sealing Foam 2
KK Thin Sealing Foam 6
LL Air Input Regulating Plate 1
MM Knob Screw 1
NN Air Inlet Cover 1
OO Thread Sealing Tape 1
PP Transformer 1
QQ LED Lamp 1
RR RTV Sealer (tube) 2
SS Vacuum Elbow 1
TT Spring Washer 4
Spare Nozzles 3
Spare Glass Film 5
LL
SS
To order parts and supplies: 800.343.9353 >> eastwood.com 3
TOOLS REQUIRED (not included)
• Phillips screwdriver
• 7mm and 10mm sockets or wrenches
• 12mm and 14mm wrenches
QQ

HOPPER ASSEMBLY
1. Peel away protective paper and apply Thin Sealing Foam (KK) on
the INNER face, along the bottom of the flanges of Hopper Back
Panel (J) and Hopper Front Panel (K) (FIG. 1).
2. Install Hooper Drain Latch (Z) onto Hopper Front Panel (K) with
loop facing small end and attach with two M4 x 10 screws (CC)
and two washers (GG) then tighten (FIG. 2).
3. Attach 1st Hopper Side Panel (L) to Hopper Front Panel (K)
with five M6 x 12mm screws (AA) and nuts (EE) trapping the
Sealing Foam between panels. (Do not fully tighten screws
at this time) (FIG. 2).
4. Attach 2nd Hopper Side Panel (L) to opposite side of Hopper Front
Panel (K) with five M6 x 12mm screws (AA) and nuts (EE) trapping
the Sealing Foam between panels. (Do not fully tighten screws at
this time) (FIG. 3).
4Eastwood Technical Assistance: 800.343.9353 >> [e-mail]
FIG. 1
FIG. 2
J
KK
KK
KK
K
EE
AA
L
Z
CC
K
FIG. 3
EE AA
L
5 Pcs. AA M6 x 12mm Screw
5 Pcs. EE M6 Nut
ASSEMBLY HAZARD!
• Install a shutoff valve on the air supply line
for emergency shutoff.
• Wear safety goggles and work gloves
during assembly.
KK
2 Pcs. CC M4 x 10mm Screw
2 Pcs. GG M4 Washer
5 Pcs. AA M6 x 12mm Screw
5 Pcs. EE M6 Nut

1. Attach Hopper Back Panel (J) to Hopper Side Panels (L) with
ten M6 x 12mm screws (AA) and nuts (EE) trapping the Sealing
Foam between panels (FIG. 4).
2. Make sure all four panel edges at top and bottom of Hopper
Assembly are flush and then evenly tighten the M6 x 12mm
screws (FIG. 4).
3. Peel away protective paper and apply Thin Sealing Foam (KK) on
the bottom of the flange of Hopper Assembly (FIG. 5).
4. Attach Hopper Bottom Frame (Y) to Hopper Assembly with
eight M4 x 10mm screws (CC) and 4mm Flat Washers (GG).
Tighten screws (FIG. 5).
5. Install the Hopper Drain Door (N) to Hopper Back Panel (J)
with three M6 x 12 mm screws and tighten (FIG. 5).
6. Attach four Hopper Corner Reinforcements (P) to the INSIDE of
Upper Hopper Flange with four M4 x 10mm screws (CC) and
4mm Flat Washers (GG). Tighten screws (FIG. 6).
To order parts and supplies: 800.343.9353 >> eastwood.com 5
FIG. 4
FIG. 5
FIG. 6
AA, EE
AA
N
Y
GG
CC
KK
GG
CC
P
J
AA, EE
J
L
10 Pcs. AA M6 x 12mm Screw
10 Pcs. EE M6 Nut
8 Pcs. CC M4 x 10mm Screw
8 Pcs. GG M4 Washers
3 Pcs. AA M6 x 12mm Screw
8 Pcs. CC M4 x 10mm Screw
8 Pcs. GG M4 Washers

6Eastwood Technical Assistance: 800.343.9353 >> [e-mail]
1. Install Media Suction Tube (O) to Hopper Front Panel (K)
with two M6 x 12mm screws (AA) and nuts (EE) (FIG. 7).
2. Peel away protective paper and apply Thin Sealing Foam (KK)
on the upper OUTER surface of the Hopper Side Panels (L).
Wrap the Sealing Foam around the front and back of the
Hopper Assembly about 1-1/4” (FIG. 8).
FIG. 7
FIG. 8
EE
AA
K
O
L
KK
KK
L
1-1/4"
2 Pcs. AA M6 x 12mm Screw
2 Pcs. EE M6 Nut

To order parts and supplies: 800.343.9353 >> eastwood.com 7
CABINET ASSEMBLY
1. Attach Cabinet Left Side Panel (E) with four M6 x 12mm Screws
(AA) in outer 4 holes only, (no screws in center holes at this
time). NOTE: Be sure that Left Side Panel (E) is installed with
the angled corner facing upward and forward (FIG. 9).
2. Install Shelf Floor Support (Q) (NOTE: open side downward)
to Cabinet Left Side Panel (E) with one M6 x 12mm Screws (AA)
(FIG. 9).
3. Attach Cabinet Right Side Panel (I) & Shelf Floor Support (Q)
with five M6 x 12mm Screws (AA) (FIG. 10).
4. Tighten all screws (FIG. 10).
5. Peel away protective paper and apply Thin Sealing Foam (KK)
along the rear flanges of Cabinet Side Panels (E) and (I) and
Hopper Back Panel (J) (FIG. 11).
FIG. 9
FIG. 10
FIG . 11
K
E
Q
AA
Q
AA
I
I
E
J
KK
5 Pcs. AA M6 x 12mm Screw
5 Pcs. AA M6 x 12mm Screw

8Eastwood Technical Assistance: 800.343.9353 >> [e-mail]
1. Attach Cabinet Back Panel (C) to the rear flanges of Cabinet
Side Panels (E) and (I) and Hopper Back Panel (J) with fifteen
M6 x 12mm screws (AA). NOTE: not all holes receive screws at
this time, refer to figure 12 for locations and be sure that larger
punched holes are in proper orientation. (Do not fully tighten
screws at this time to allow for alignment of remaining leg holes.)
(FIG. 12).
2. Install 2 Legs (G) to the rear flanges of Cabinet Side Panels (E)
& (I), Cabinet Back Panel (C) and Hopper Back Panel (J) with
sixteen M6 x 12mm screws (AA) and nuts (EE). Do not fully
tighten screws at this time (FIG. 12).
3. Peel away protective paper and apply Thin Sealing Foam (KK)
along the front-facing flanges of Cabinet Side Panels (E) and (I)
and Hopper Front Panel (K) (FIG. 13).
4. Attach Cabinet Front Panel (H) to the front flanges of Cabinet
Side Panels (E) & (I) and Hopper Front Panel (K) with thirteen M6
x 12mm screws (AA). NOTE: not all holes receive screws at this
time, refer to figure 12 for locations. (Do not fully tighten screws
at this time to allow for alignment of remaining leg holes) (FIG.
14).
5. Install 2 Legs (G) to the rear flanges of Cabinet Side Panels (E)
and (I), Cabinet Front Panel (H) and Hopper Front Panel (K) with
sixteen M6 x 12mm screws (AA) and nuts (EE). Do not fully
tighten screws at this time (FIG. 14).
FIG. 12
FIG. 13
FIG. 14
E
I
AA
G
G
C
E
I
KK
K
H
G
AA
G
29 Pcs. AA M6 x 12mm Screw
14 Pcs. EE M6 Nut
31 Pcs. AA M6 x 12mm Screw
20 Pcs. EE M6 Nut

To order parts and supplies: 800.343.9353 >> eastwood.com 9
INSTALLING
REMAINING COMPONENTS
1. Stand assembled unit up on it’s legs (FIG. 15).
2. Tighten leg screws to ensure unit sits level.
3. Install the Media Blasting Gun (W) Suction Hose to the Media
Suction Tube (O), secure with a Hose Clamp and tighten (FIG. 15).
4. Place the Media Blasting Gun (W) Air Supply Hose Fitting through
the through hole in the lower right corner of the Cabinet Front
Panel (H) using a large flat washer on either side. Wrap thread
sealing tape around fitting threads and secure with the
Air Supply Fitting Nut (FIG. 15).
5. Let the Media Blasting Gun (W) hang out of the right front corner
of the Cabinet (FIG. 15).
6. Set the Shelf (B) (with angled cut off corner toward right front of
cabinet) and allow it to rest on the hopper flanges and Shelf
Floor Support (Q) (FIG. 15).
7. From the outside, install 2 sets of Seal Rings (U) and Glove Seats
(V) into the large holes in the Cabinet Front Panel (H) and secure
with twelve M4 x 16mm screws (BB), flat washers, (GG) and nuts
(FF) (FIG. 16).
8. Fit 2 Hose Clamps (S) over the Glove Sleeves then slide the Gloves
(R) fully over the Glove Seats (V) then tighten Hose Clamps (S)
securely (FIG. 16). NOTE: Be sure to install left and right hand
gloves on the correct side and position them with thumbs upward.
9. From the outside, install the Air Input Regulating Disk (LL) over the
six hole array on the upper rear corner of the Cabinet Back Panel
(C) and secure with Knob Screw (MM) (FIG. 17).
10. From the inside, install the Vacuum Elbow (SS) with grommet.
Next, install the Vacuum Baffle (X) over the vacuum hole on the
upper left corner of the Cabinet Back Panel (C) and secure with
four M6 x 12mm screws (AA) and nuts (EE) (FIG. 17).
FIG. 15
FIG. 16
FIG. 17
H
B
W
Air Supply
Hose Fitting
Washer Air Supply
Fitting Nut
Air Flow
H
H
SR
U
V
BB
V
U
BB
FF, GG
AA C
MM LL
FF, GG
CC
EE
X
M
M
H
12 Pcs. BB M4 x 16mm Screw
12 Pcs. GG M4 Washers
12 Pcs. FF M4 x 12mm Screw
B
4 Pcs. AA M6 x 12mm Screw
4 Pcs. EE M6 Nut
1 Pc. SS Vacuum Elbow
SS

10 Eastwood Technical Assistance: 800.343.9353 >> [e-mail]
11. Install Latches (M) to the upper corners of the Cabinet Front
Panel (H) and secure with four M4 x 10mm screws (CC), flat
washers, (GG) & nuts (FF) (FIG. 17).
12. Peel away protective paper and apply Sealing Foam (KK) on the
exposed level flange areas on the top of the Cabinet Side Panels
(E) and (I) and along the top edge of the Cabinet Back Panel (C)
(FIG. 18). NOTE: Be sure that no gaps exist between sections of
sealing foam.
13. Snap LED Lamp (QQ) into Lamp Clips (FIG. 19).
14. Route the cord of the LED Lamp (QQ) through the hole in the
upper area of Cabinet Side Panel (E) then thread the cord ferrule
into the hole (FIG. 19).
15. Bolt down Box Top Panel with eleven M6 x 12 screws and nuts.
16. Connect the LED Lamp (QQ) wires to the Switch (F) wires. At-
tach Blue Wire to Blue wire connection and Brown Wire to the
Gray wire connection (FIG. 19). NOTE: Needle Nose pliers may
be useful for inserting wires to switch connection.
17. Attach Switch (F) to Cabinet Side Panel (E) with two M4 x 10mm
screws (CC), washers (GG) and nuts (FF) (FIG. 19). NOTE: Be
sure to position the switch facing forward towards operator.
18. Peel away protective paper and apply Thick Sealing Foam (JJ)
on the remaining exposed angled flange areas on the opening
of the Cabinet Assembly (FIG. 20). NOTE: Be sure that no gaps
exist between sections of sealing foam.
19. Attach Door (A) hinge plate to the Cabinet Top (D) with six M6 x
12mm screws (AA) and nuts (EE) (FIG. 20). NOTE: Do not let door
fall backward against top or glass window breakage will result.
FIG. 18
FIG. 19
FIG. 20
E
KK
C
I
AA
FF
TT
D
GG
FF
F
CC
E
JJ
JJ
JJ
JJ
I
H
E
2 Pcs. CC M4 x 10mm Screw
2 Pcs. GG M4 Washers
2 Pcs. FF M4 Nut
6 Pcs. AA M6 x 12mm Screw
6 Pcs. EE M6 Nut
blue wire blue wire
gray wire
brown wire Lamp Wire
Connection
QQ