EasyPro EP120 Use and care manual

Mag Drive Pumps
Instructions for Operation • Safety • Warranty
Thank you for purchasing the EasyPro Mag Drive pump. This
pump is a magnetically driven water pump. It contains no oil,
rotating shafts, shaft seals or bearings. This pump combines
simplicity of design with the most energy efficient operation of
any pump. All electrical components are encapsulated in epoxy.
The impeller assembly consists of impeller blades attached to a
magnet and is easily replaced should the need arise. There are
threaded discharge and intake ports on all models.
Safety & Electrical Connections
1. Always disconnect the electrical supply before handling, maintaining, repairing or install-
ing any pond equipment.
2. Connect this product only to a 110 volt receptacle that is protected by a Ground Fault Circuit
Interrupter (GFCI).
3. The pump must be fully submersed underwater at all times when operating.
4. Never let the pump run dry, as this can damage the impeller, over heat the pump and possibly
burn out the pump.
5. Do not use this product in bathrooms or swimming pools.
6. All electrical work must be performed by a qualified technician. Always follow the National
Electrical Code (NEC) or the Canadian Electrical Code as well as all local, state and provincial
codes. Code questions should be directed to your local electrical inspector. Failure to follow
electrical codes and OSHA safety standards may result in personal injury or equipment dam-
age. Failure to follow manufacturer’s installation instructions may result in electrical shock, fire
hazard, personal injury or death, damaged equip-ment, provide unsatisfactory performance,
and may void manufacturer’s warranty.
7. When installing a check valve assembly, thread in the assembly finger tight. Do not overtighten
as this could crack the housing and void the warranty.
EP120 • EP200 • EP400 • EP600 • EP850
EP1050 • EP1350 • EP1750 • EP2200 • EP3200
1

8. Do not remove the pre-filter or the pre-filter cover from the pump as this will cause excess de-
bris to enter the pump and may void the warranty.
Troubleshooting:
If the pump fails to operate, please check the following before contacting EasyPro:
Note: Always disconnect from electrical outlet before handling the pump.
1. Check the GFCI circuit breaker or try another GFCI electrical outlet to ensure the pump is get-
ting power.
2. Check the tubing for kinks and obstructions. Check filter cover and foam filter for blockage.
Follow cleaning steps in the maintenance section if blockage is suspected.
3. If necessary, remove and clean the impeller assembly.
Service & Maintenance
1. Disconnect all power supplies before service.
2. It is highly recommended to place the pump in either an EasyPro skimmer or into an EasyPro
pump protector.
3. Clean the intake screen and foam filter
when the flow is visibly reduced.
4. Clean the pump and impeller with clean
fresh water.
5. When cleaning the pump and impeller,
be careful not to loose the small plastic
washers positioned at the top and bot-
tom of the impeller. These washers are
critical to the quiet and efficient opera-
tion of the pump.
6. Check inside the impeller housing for
large debris or algae that could reduce
the flow.
7. Clean the impeller housing using cotton
swabs. Clean the outside of the impeller
with a damp cloth and clean water.
Fountain Nozzles
Complete Set
Diverter Valve
2
Foaming
Jet
Volcano
Double Volcano
Waterbell

Part # Foam Filter # Impeller Part #
EP120 EP120F EP120I
EP200 EP200F EP200I
EP400 EP400F EP400I
EP600 EP600F EP600I
EP850 EP820F EP850I
EP1050 EP1050F EP1050I
EP1350 EP1350F EP1350I
EP1750 EP1750F EP1750I
EP2200 EP2200F EP2200I
EP3200 EP3200F EP3200I
EP4N EASY PRO FOUNTAIN NOZZLE SET
Replacement Parts for the EP200 — EP3200 Mag Drive Pumps
Fountain Nozzles Available on Mag Drive Pumps
EP120 EP200 EP400 EP600 EP850 EP1050 EP1350 EP1750 EP2200 EP3200
Waterbell x x x x x x x NA NA NA
Volcano x x x x x x x NA NA NA
Double Volcano x x x x NA NA NA
Foaming Jet x NA NA NA
Waterbell Volcano Double Volcano Foaming Jet
Operation of Pumps & Attachments
All EasyPro Mag Drive Pumps, EP120 – EP1350, come with fountain nozzles and diverter valves to
easily hook up a second water feature. Below are samples of each type of fountain nozzles. Note:
Not all pumps come with all fountain nozzles. If additional nozzles are desired please see the
parts list.
3

Warranty:
This product is warrantied against any mechanical or material defects for a period of three years from
the date of purchase (impellers are covered by a six month period against manufacturers defect). War-
ranty only covers properly installed and maintained units.
The warranty does not cover normal wear and tear, nor any deterioration suffered through overloading,
improper use, negligence or accident. Similarly, any modification made by the purchaser to the product
will cause the warranty to be null and void.
All returned items will be inspected to determine cause of failure before warranty is approved.
Warranty does not cover any cost associated with the installation or removal of the product subject to
warranty claim.
An RA number must be obtained by calling EasyPro Pond Products at 800-448-3873. It is your respon-
sibility to pay the return shipping charges. Be sure to include the RA number, original receipt (in the form
of an invoice or sales receipt), name, return address and phone number inside of the package. No war-
ranty claims will be honored without the original receipt.
Ensure the product is properly packaged and insured for the replacement value. Damage due to im-
proper packaging is the responsibility of the sender.
The manufacturer or supplier shall not be held liable for any damages caused by defective components
or materials of this product; or for loss incurred because of the interruption of service; or any conse-
quential/incidental damages and expenses arising from the production, sale, use or misuse of this
product.
The manufacturer or supplier shall not be held liable for any loss of fish, plants or any other livestock as
a result of any failure or defect of this product.
800-448-3873 • Grant, Michigan
www.EasyProPondProducts.com • [e-mail]
10-08