EasyPro ES1250 User manual

Submersible Pump/Filter/UV Combo
Thank you for purchasing the EasyPro Submersible Pump/Filter/UV Combo. This
compact all-in-one unit works eciently to keep the water in your pond or water feature
clear and clean. In addition to removing solids this unit provides biological ltration and
includes a ultraviolet clarier to kill free oating algae. The UV clarier has its own plug to
be used only when needed to kill oating algae. A set of nozzles is included to provide the
option of a decorative fountain in your pond.
Please read this instruction booklet carefully before use to assure that you safely and
correctly use this product.
ESF1250
Safety and Warnings:
1. Be sure to read and follow all safety instructions
2. Always disconnect the electrical supply before handling,
maintaining, repairing or installing any pond equipment. Do not
immerse or attempt to use a wet plug.
3. WARNING: Risk of electric shock. Install unit only to a
covered Class A 115 volt GFCI protected receptacle that is
weatherproof with the power unit connect to the receptacle.
4. Provide a “drip loop” with the power cords by making a “loop” of cord
below the power receptacle. This prevents water from traveling along the cord into the receptacle.
5. This unit has not been approved for use in swimming pools or spas.
6. Do not use if power cord is damaged. Cord is not repairable and damaged unit should be discarded.
7. The integrated pump must be fully submersed underwater at all times when operating. Never let the pump
run dry, as this can damage the impeller or overheat and possibly burn out the pump.
8. Do not use to pump oil or other non-intended liquids.
9. DANGER: Do not operate the UV lamp outside the housing of the unit. UV radiation can be harmful to
skin and eyes.
Model ESF1250
Pump 650 GPH Mag Drive
Voltage 115 Volt/60Hz
Max Flow 650 GPH
Pond Size 250-1250 Gallons
Wattage 50 Watts
Power Cables 15 feet
Fountain Nozzles Three-tier, two-tier, waterbell
UV-C Lamp 11 Watt
Ballast cUL listed 115V / 60Hz

UV Installation and Maintenance
WARNING: Disconnect the unit from power source before performing any maintenance or installation
on the unit.
USE A CLEAN CLOTH TO HANDLE THE UV LAMP, TOUCHING THE LAMP CAN GREATLY REDUCE ITS LIFE
Instructions for replacing and cleaning UV lamp and quartz sleeve. Periodic cleaning of the quartz sleeve may
be necessary for the UV light to reach the bacteria. If the UV lamp is functional and intact, the sleeve may be
replaced or cleaned with a soft cloth and reassembled. After a year of continuous use the lamp may still light
but the UV eectiveness is diminished.
3. Unscrew and remove the large
threaded cap on the UV housing to
reveal inner UV assembly.
6. Remove grommet from end of the
lamp and set aside, gently pull lamp
out of the socket and discard.
9. Reinsert UV assembly into plastic
housing, tighten cap and replace
everything back into base.
1. Unscrew fountain assembly, then
remove top cover from unit.
5. To replace lamp, unscrew threaded
ring that holds the quartz sleeve in,
and remove sleeve from UV assembly.
7. Using a clean soft cloth remove the
new lamp from its package and gently
push the lamp into the socket. Do
not touch the UV lamp with your
ngers.
2. Remove three Phillips screws on
pump, pull pump out of base and set
aside.
4. If the UV lamp is functional and intact,
sleeve may be replaced or cleaned
with a soft cloth and reassembled.
8. Replace grommet to the end of the
lamp and reinsert into quartz sleeve.

Installation & Operation
WARNING: Disconnect the unit from power
source before performing any maintenance
or installation on the unit.
1. Determine the exact place to install lter. The lter
base must be completely submerged and sit on a
at level surface.
2. Choose your fountain nozzle and use diagram
below to build fountain assembly and attach to
pump body.
3. Level the fountain assembly using ball-joint.
4. Plug in the pump and adjust diverter valve to
desired fountain spray.
5. Only operate UV unit when the pump is running.
6. If regular benecial bacteria treatments are used
in the pond, turn the UV unit o for at least 24
hours to allow treatments to be most eective.
Fountain Assembly
Maintenance
Refer to previous page for UV lamp and quartz
sleeve replacement. Filter pads and media are
wearable items that may be replaced periodically.
1. Pick up unit out of water and unscrew fountain
assembly. Do not pick up lter by power cord.
2. Remove top cover from unit and take out lter
pads and media.
3. Flush lter pads and media with water or replace.
4. Reassemble lter pads with the correct orientation
and replace top cover.
5. Reattach fountain assembly and return unit to
water.
6. In freezing climates be sure to remove the unit
from the pond and store during the winter.
Three Tier Nozzle
Waterbell Nozzle
Pump extension tting
Ball-joint Two Tier Nozzle
Fountain extension tube
Diverter valve with cap or barbed
tting for optional hose attachment

800-448-3873 • Grant, Michigan
www.easypropondproducts.com • [e-mail]
3-13
Replacement Parts
Warranty
This product is warranted against any mechanical or material defects for a period of one year from the
date of purchase (UV lamp, quartz sleeve, pump impeller, and lters are wear items and are not covered by
warranty). Warranty only covers properly installed and maintained units.
The warranty does not cover normal wear and tear, nor any deterioration suered through overloading,
improper use, negligence or accident. Similarly, any modication made by the purchaser to the product will
cause the warranty to be null and void.
All returned items will be inspected to determine cause of failure before warranty is approved.
Warranty does not cover any cost associated with the installation or removal of the product subject to
warranty claim.
An RA number must be obtained by calling EasyPro Pond Products at 800-448-3873. It is your
responsibility to pay the return shipping charges. Be sure to include the RA number, original receipt (in the
form of an invoice or sales receipt), name, return address, and phone number inside of the package. No
warranty claims will be honored without the original receipt.
Ensure the product is properly packaged and insured for the replacement value. Damage due to improper
packaging is the responsibility of the sender.
The manufacturer or supplier shall not be held liable for any damages caused by defective components or
materials of this product; or for loss incurred because of the interruption of service; or any consequential/
incidental damages and expenses arising from the production, sale, use or misuse of this product.
The manufacturer or supplier shall not be held liable for any loss of sh, plants or any other livestock as a
result of any failure or defect of this product.
Part # Description
ESF1250B Ultraviolet Lamp
ESF1250S Quartz Sleeve
ESF1250I Pump Impeller
ESF1250F Filter Pad & Media