EasyPro EPS650 Use and care manual

Stainless Steel Mag Drive Pumps
Ideal for ponds and waterfalls!
Instructions for Operation • Safety • Warranty
Thank you for purchasing the EasyPro Mag Drive pump. This pump is a
magnetically driven water pump. It contains no oil, rotating shafts, shaft seals
or bearings. This pump combines simplicity of design with the most energy
efficient operation of any pump. All electrical components are encapsulated
in epoxy. The impeller assembly consists of impeller blades attached to a
magnet and is easily replaced should the need arise. There are threaded dis-
charge and intake ports on all models.
Safety & Electrical Connections
1. Always disconnect the electrical supply before handling, maintaining,
repairing or installing any pond equipment.
2. Connect this product only to a 110 volt receptacle that is protected by a Ground Fault Circuit
Interrupter (GFCI).
3. The pump must be fully submersed underwater at all times when operating.
4. Never let the pump run dry, as this can damage the impeller, over heat the pump and possibly
burn out the pump.
5. Do not use this product in bathrooms or swimming pools.
6. All electrical work must be performed by a qualified technician. Always follow the National
Electrical Code (NEC) or the Canadian Electrical Code as well as all local, state and provincial
codes. Code questions should be directed to your local electrical inspector. Failure to follow
electrical codes and OSHA safety standards may result in personal injury or equipment dam-
age. Failure to follow manufacturer’s installation instructions may result in electrical shock, fire
hazard, personal injury or death, damaged equipment, provide unsatisfactory performance, and
may void manufacturer’s warranty.
7. When installing a check valve assembly, thread in the assembly finger tight. Do not overtighten
as this could crack the housing and void the warranty.
EPS650 • EPS1250 • EPS2350

Troubleshooting:
If the pump fails to operate, please check the following before contacting EasyPro:
Note: Always disconnect from electrical outlet before handling the pump.
1. Check the GFCI circuit breaker or try another GFCI electrical outlet to ensure the pump is get-
ting power.
2. Check the tubing for kinks and obstructions. Check intake screen for blockage. Follow cleaning
steps in the maintenance section if blockage is suspected.
3. If necessary, remove and clean the impeller assembly.
Service & Maintenance
1. Disconnect all power supplies before service.
2. It is highly recommended to place the pump in either an EasyPro skimmer or into an EasyPro
pump protector.
3. Clean the intake screen when the flow is visibly reduced.
4. Clean the pump and impeller with clean fresh water.
5. When cleaning the pump and impeller, be careful not to loose the small plastic washers posi-
tioned at the top and bottom of the impeller. These washers are critical to the quiet and efficient
operation of the pump.
6. Check inside the impeller housing for large debris or algae that could reduce the flow.
7. Clean the impeller housing using cotton swabs. Clean the outside of the impeller with a damp
cloth and clean water.
Limited Warranty:
This limited warranty is for any mechanical or material defects for a period of three years from the date of purchase (impellers
are covered by a six month period against manufacturer’s defect). Warranty only covers properly installed and maintained units.
The warranty does not cover normal wear and tear, nor any deterioration suffered through overloading, improper use, negligence
or accident. Similarly, any modification made by the purchaser to the product will cause the warranty to be null and void.
All returned items will be inspected to determine cause of failure before warranty is approved.
Warranty does not cover any cost associated with the installation or removal of the product subject to warranty claim.
An RA number must be obtained by calling EasyPro Pond Products at 800-448-3873. It is your responsibility to pay the return
shipping charges. Be sure to include the RA number, original receipt (in the form of an invoice or sales receipt), name, return ad-
dress and phone number inside of the package. No warranty claims will be honored without the original receipt.
Ensure the product is properly packaged and insured for the replacement value. Damage due to improper packaging is the
responsibility of the sender.
The manufacturer or supplier shall not be held liable for any damages caused by defective components or materials of this
product; or for loss incurred because of the interruption of service; or any consequential/incidental damages and expenses aris-
ing from the production, sale, use or misuse of this product.
The manufacturer or supplier shall not be held liable for any loss of fish, plants or any other livestock as a result of any failure or
defect of this product.
800-448-3873 • Grant, Michigan
www.EasyProPondProducts.com • [e-mail]
4-10