Eaton P1 I2 Series Manual

Electric current! Danger to life!
Only skilledor instructedpersons may
carry out the following operations.
Lebensgefahr durch elektrischenStrom!
Nur Elektrofachkräfte undelektrotechnisch
unterwiesene Personen dürfen die im Folgenden
beschriebenen Arbeiten ausführen.
Tension électrique dangereuse !
Seules les personnes qualifiées et averties doivent
exécuter les travaux ci-après.
¡Corrienteeléctrica! ¡Peligro de muerte!
El trabajo a continuación descrito debe ser realizado
por personas cualificadas y advertidas.
Tensione elettrica: Pericolo di morte!
Solo persone abilitate e qualificate possono eseguire
le operazioni di seguito riportate.
触电危险！触电危险！
只允许专业人员和受过专业训练的人员进行
下列工作。
Электрическийток! Опасно для жизни!
Только специалисты или проинструктированные
лица могут выполнять следующие операции.
en
de
fr
es
it
zh
ru
Emergency On Call Service:Local representative (Eaton.eu/aftersales)or [phone] (de, en) 1/2
Instruction Leaflet
Montageanweisung
Notice d’installation
Instrucciones de montaje
Istruzioni per il montaggio
安安装说明装说明
Инструкция по монтажу
04/18 IL03802001Z
P1…/I2…
P1…/I2(H)(-RT)P1…/I2(H)/SVB(-SW)
P1…/I2(H)(-RT)
P1…/I2(H)/SVB(-SW)
ON
OFF
d
b
≦3 x
d = 4 - 8 mm
b + d≦47 mm
(d = 0.16 - 0.31“)
(b + d ≦1.85“)
a
P1 10.5 mm (0.41")
HI11-P1/P3 7.5mm(0.3")
K-CI-K1/K2 9mm (0.35")
P1… P1…/N P1…/HI11
a
UL-File: E 36 332
Suitable For UseAs Motor Branch Circuit
Disconnecting Means With Suffix SVB.
Break All Lines.
HI11-P1/P3 tightening
torque
0.5 - 1.5 mm21 Nm
(8.85 lb-in)
0.75 - 2.5 mm2
AWG 18 -AWG 14
P1… tightening
torque
1 x 1.0 -4.0 mm2
2 x 1.0 -4.0 mm21.6Nm (14.16 lb-in)
1 x 1.5 -6.0 mm2
2 x 1.5 -6.0 mm2
AWG14 - AWG 8
75 °C Cuwire only
1
L1 L2 L3
T1 T2 T3
2
3
4
5
6
0
I
N
N
1
L1 L2 L3
T1 T2 T3
2
3
4
5
6
0
I
14
13 21
22
1
L1 L2 L3
T1 T2 T3
2
3
4
5
6
0
I
ON
OFF
ON
OFF
2 x ST 3.9 x 19
1Nm(8.85 lb-in)
1.2 Nm
(10.62 lb-in)
0.6 Nm
(5.31 lb-in)
0.6 Nm
(5.31 lb-in)
ZFS(NT)...T0

2/2Emergency On Call Service: Local representative (Eaton.eu/aftersales)or [phone] (de, en)
04/18 IL03802001Z
Eaton Industries GmbH, Hein-Moeller-Straße 7-11, 53115 Bonn, Germany 04/18 IL03802001Z
©1999 by Eaton Industries GmbH,Eaton.eu/documentation Eaton.com/recycling All Rights Reserved Printed in Great Britain (04/18)
P1…/I2…
V-M25 KT-M25
P1.../I2 (H)(-NA): ⌀ ≦ 11 mm (⌀ ≦ 0.43”)
K-CI-K1/2
N-P1Z HI11-P1/P3Z
P1...
P1.../I2(H)(-NA)
⌀ ≦ 8 mm
(⌀ ≦ 0.31”)
P1.../I2...: V-M25
P1.../I2(H)(-NA): ⌀ ≦ 16 mm (⌀ ≦ 0.63”)
P1.../I2...: V-M25
P1.../I2(H)(-NA): ⌀ ≦ 16 mm (⌀ ≦ 0.63”)
1P1…/I2(H)(-NA)
2
3 4
￫If you want to usebothN-P1Z and HI11-P1/P3,
you will have to remove terminal K-CI-K1/2. ￫Con l’utilizzo di ambedue N-P1Z eHI11-P1/P3 il morsetto K-CI-K1/2 deveessererimosso.
￫Bei gemeinsamer Verwendung vonN-P1Z und
HI11-P1/P3 muss die KlemmeK-CI-K1/2 entfernt
werden.
￫
N-P1Z 和HI11-P1/P3 同时使用时，
必须移除端子 K-CI-K1/2。
￫
L’utilisation de N-P1Z et HI11-P1/P3en même
temps requiertle démontage de la borneK-CI-K1/2
￫Приодновременномиспользовании
N-P1Z иHI11-P1/P3 необходимоубрать
клемму K-CI-K1/2.
￫Al utilizar N-P1Z y HI11-P1/P3 juntosdebe
eliminarse el borne K-CI-K1/2.
1 2 3
ON
OFF
171 mm (6.73”)
100 mm (3.94”)
M4
80 mm (3.15”)