Eaton Transformer 5000 User manual

www.eaton.com
Standard Features
wTransformer 5000
provides isolation and
step-down 120 VAC outlets
wMultiple output receptacles: 120 VAC
wInput power cable with
L6-30P plug
wDip switch to select 208
or 240 VAC input
w2 — L5-20R protected by individual
breakers.
w6 — L5-15R protected by two breakers
(one breaker for 3 receptacles)
Transformer 5000
Quick Start

STEP 1: Transformer 5000 Unpacking and Parts Check (87102)
Transformer 5000
Quick Start Manual
Tr ansformer 5000 Box Contents
Tower Stand Extenders
Stabilizer Bracket
(4 screws included)
Telescopic Rails
for Rack Mount
49
45
54
43 51
STEP 2: Transformer 5000 Tower Configuration
To wer Configuration of Standard System with Tr ansformer Module
1
1
2
2
4
4
4
4
33
Transformer 5000
MX 5000 RT
EXB RT
(up to 3)
5
86-87102-00 A01 - Page 2
EX RT Transformer Module

STEP 3: Transformer 5000 Rack Configuration
LOAD4/120V~,16ALOAD1
120V~,16A
LOAD2
120V~,16A
SETTHIS
SWITCHWHEN
UNPOWERED
BYALLSOURCES
INPUTVOL
T
AGE
SELECTION
240~
208~
INPUT
BREAKER
TRANSFORMER
PROTECTION
LOAD3/120V~,16A
LOAD3
BREAKER
LOAD1
BREAKER
LOAD2
BREAKER
LOAD4
BREAKER
LOAD4/ 120V~,16A
LOAD1
120V~,16A
LOAD2
120V~,16A
SETTHIS
SWITCHWHEN
UNPOWERED
BYALLSOURCES
INPUTVOL
T
AGE
SELECTION
240~
208~
INPUT
BREAKER
TRANSFORMER
PROTECTION
LOAD3/ 120V~,16A
LOAD3
BREAKER
LOAD1
BREAKER
LOAD2
BREAKER
LOAD4
BREAKER
LOAD4/120V~,16ALOAD1
120V~,16A
LOAD2
120V~,16A
SETTHIS
SWITCHWHEN
UNPOWERED
BYALLSOURCES
INPUTVOL
T
AGE
SELECTION
240~
208~
INPUT
BREAKER
TRANSFORMER
PROTECTION
LOAD3/120V~,16A
LOAD3
BREAKER
LOAD1
BREAKER
LOAD2
BREAKER
LOAD1
120V~,16A
LOAD2
120V~,16A
SETTHIS
SWITCHWHEN
UNPOWERED
BYALLSOURCES
INPUTVOL
T
AGE
SELECTION
240~
208~
INPUT
BREAKER
TRANSFORMER
PROTECTION
LOAD1
BREAKER
LOAD2
BREAKER
3
4
4
4
42
2
1
4
4
5
1
66
6
6
STEP 4: Transformer, UPS, and MX EXB RT Systems Connections
Transformer
5000
Input
Cable
L6-30P
MX EXB
Battery
MX EXB
Battery
MX 5000 RT
UPS
Transformer
5000
15
1
17
19
See System Installation and User Manual for details and initial start-up procedures.
86-87102-00 A01 - Page 2
Quick Start
1. Attach both front mounting ear brackets to
Transformer 5000 module with supplied
screws (for this step, it is possible to adjust
the position of both front mounting brackets).
2. Attach rear support brackets to module.
These brackets prevent the Transformer 5000
module from sliding out of the rack.
3. Attach rails together and secure with wing
nuts, and finger tighten both sides.
4. Attach both rails to rear and front of rack with
supplied flathead screws (as shown).
The UPS may remain connected
to AC source while installing the
transformer.
1. Connect the transformer input
cable L6-30P (17) to one of the
UPS outlets L6-30R (1).
2. Connect the 120V load to the
outlet of transformer (15) or (19).
Note: If an “RCD” load is connected
to the transformer, the UPS may go
into bypass mode, sound an alarm,
and perform self diagnostics for 23
seconds before returning to normal
operation.
5. Use caution when sliding unit
into rack. Temporarily secure
unit to rack with thumb screws
on front mounting brackets.
6. Secure rear support brackets to
rails.

www.eaton.com
86-87102-00 A01