Eaton EG2-NA User manual

EG2-NA
Ethernet Gateway
Installation guide
Eaton Lighting Systems

Eaton Lighting Systems EG2-NA 9850-000225-02 2
Please Read This First
The EG2-NA is built and tested to strict safety regulations. By following the steps listed
below and elsewhere within this guide, you can ensure safe installation and operation of
these controller units.
• The EG2-NA must be installed only by a qualified electrician.
• The installation must comply with the appropriate electrical codes and regulations in
force in your area.
• The EG2-NA is designed for indoor installation and use only.
• Ensure that all wiring used conforms fully to local specifications and is sufficiently
rated for the installation.
• All new wiring must be fully verified before applying power.
• The high voltage supply should be fed to the EG2-NA via an external isolation breaker
with sufficient capacity for the planned installation.
• Ensure that the supply is fully isolated at an external breaker before removing
the chassis covers. Test that power has been removed before starting to handle
conductors.
• Ensure that high voltage and low voltage wiring remains separate.
Contents
Safety 2
Introduction 3
Dimensions 3
Specification 3
Weight 3
Product Overview 4
Mounting 4
Supply Wiring 5
Control Wiring 5
Setup Instructions 6

Eaton Lighting Systems EG2-NA 9850-000225-02 3
Introduction
The Ethernet Gateway provides a connection
between an iLumin or iLight lighting control
network and an Ethernet Local Area Network,
either through an Ethernet switch or wireless
router.
The EG2-NA acts as a host for the iLumin or
iLight series of remote applications including
iOS (iPhone/iPod Touch/iPad & Android OS
devices). Coupling the EG2-NA to a Wi-Fi
network enables secure scene control,
visual feedback and modification from your
hand held device. Once configured, the
EG2-NA automatically loads room and scene
information to the connected hand held
device.
In addition to its handheld device capability,
the EG2-NA houses internal webserver pages
that allow for basic scene control functions.
These internal pages are accessed through an
internet browser and are password protected
for security.
The EG2-NA also facilitates the commissioning
of the iLumin or iLight system, allowing our
factory trained technicians to use the EG2-NA
connection to configure the control system on
a LAN or Wi-Fi enabled PC or via the internet
rather than by connecting directly into the
iLumin or iLight network.
Weight
• Packed: 2.6 kg (5.7 lbs)
• Unpacked: 2.4 kg (5.3 lbs)
Dimensions
Specication
Unit requires: 120-240 VAC 50/60 Hz 0.45A 1Ø
Maximum
iCAN network connection
Ethernet connection: Fully transformer isolated
Ambient temperature range: 0°C to 40°C
(32°F to 104°F)
Humidity: 20% to 90% non-condensing
Configuration and sequence memory
Field upgradable FLASH program memory
Internal +15 VDC, 2A power supply

Eaton Lighting Systems EG2-NA 9850-000225-02 4
Product Overview Mounting
Location and spacing
The EG2-NA should be installed in a dry
ventilated location, where ambient conditions
are maintained within the requirements of the
unit.
The unit has ventilation slots on its sides
to allow convection cooling and under no
circumstances should these be blocked.
Allow 50mm (2”) above and below the unit if
trunking with a depth greater than 50mm (2”)
is used.
Mounting Holes
The unit is provided with four 6mm (1/4in)
diameter fixing holes for wall mounting.
The mounting holes can be accessed by
undoing the four screws on the front cover and
removing it.
1. Ethernet Connection
2. CAN ID Button
3. iCAN Network Connector with a green
(power) and yellow (network activity) LED
4. Main Supply Terminal Block
5. Power Supply
6. Reset Button
1
2
3
4
5
6
6.89” (175mm)
7.09” (180mm)
0.25" (6.35mm)
Mounting Holes
4-O.

Eaton Lighting Systems EG2-NA 9850-000225-02 5
Supply Wiring
Connecting the Supply
This unit requires a 120-240 VAC single phase
supply (live and neutral) with 0.45 A capability.
A terminal block is used to connect the
incoming feed to the internal power supply.
Control Wiring
iCAN Network
A removable 5 position terminal block is
provided for the connection of iCAN network
cables. If the EG2-NA is located in the middle
of the network, incoming and outgoing cables
will terminate within the same connector.
iCAN Connectors
Cable type: Cooper LC or Belden 1502R or 1502P
Maximum cable length: 305m (1000’) *
Devices per segment: 100 (without bridge or
repeater)
* A maximum segment distance of 1000m (3200’) is possible
if an additional 12V power supply and bridge/repeater is used.
Wire Gauge for Supply Terminals
The live, neutral and earth ground power
connections are made to the terminal
block provided for main power connection.
Recommended cable size for live, neutral, and
earth is 26 AWG - 10 AWG.
Live (Gray)
Neutral (Blue)
Earth (Green/Yellow)
Live (Gray)
Neutral (Blue)
Earth (Green/Yellow)
Termination OFF
Termination ON
+12V
(Red)
CAN-H
(White)
SHIELD
(Gray)
CAN-L
(Blue)
0V
(Black)
iCAN
Device
iCAN
Device
EG2-NA
The EG-2-NA
has in-built
network
termination.
If the
EG-2-NA is
at the end of
the network,
ensure the
CAN TERM
jumper is
fitted in the
Termination
ON position.
iCAN devices are ‘daisy-chained’ on the
network. Spurs from the Network are not
permitted and will result in communications
problems. Devices on an iCAN network can
be wired in any order. Termination is required
at both ends of the network.
T - Indicates where a termination is required.

Eaton Lighting Systems EG2-NA 9850-000225-02 6
Setup Instructions
Ethernet Network
Connect the provided RJ45 (568B) jack to an
Ethernet Switch or Wireless Router.
Conguration
iCAN Device Number
The EG2-NA is supplied with a iCANnet Device
number with Segment number 255 and a node
number in the range 1-255. Both Segment and
Node number can be changed using iCANsoft.
Power Up
The EG2-NA takes approximately 60 seconds
to be ready for use once power is applied.
Wait for the Green CAN LED to flash slowly.
The Green Power LED will double flash
continuously while EG2-NA is on. If Ethernet is
connected the Link and Data LEDs will indicate
successful connection.
Setting the IP Address
The factory set IP Address can be changed
using iCANsoft software either through a direct
PC Node connection through the iCANnet or
directly into the Ethernet port of the EG2-NA.
PC Node Method
Connect a computer running iCANsoft to the
iCAN network using an iLight/iLumin PC Node.
Search the network and load the EG2-NA into
iCANsoft.
Open the EG2-NA device and select the
Ethernet tab. Type in the desired settings.
Select OK or Apply to downoad the changes
to the EG2-NA.
To restore settings back to default, select the
‘Restore Settings’ button. Select OK or Apply
to download the changes to the EG2-NA.
NOTE: The EG2-NA default settings are to
use a fixed IP address of 192.168.0.100.
Any device used to communicate with
the EG2-NA will need to be located within
the 192.168.0.x subnet unless IP Address
settings are changed.
Factory Default IP Settings
• IP Address 192.168.0.100
• Mask 255.255.255.0
• Default Gateway 192.168.0.1
• DHCP Off
Ethernet Input

Eaton Lighting Systems EG2-NA 9850-000225-02 7
Ethernet Port Method
The EG2-NA is supplied from the factory
without DHCP enabled and with a factory
default IP address assigned. In order to
communicate to the EG2-NA using the
Ethernet port, the PC being used must be
configured on the same subnet as the default
IP address. For details of setting the IP
address of your computer consult information
online specific to your Operating System.
If the EG2-NA you are configuring is at the
factory default settings, the following settings
are suggested when assigning a static IP
address to your computer:
Reset to Factory Defaults
Factory defaults may be reset by the following
procedure:
• Remove power from the board.
• Press the CAN ID button and reapply power.
Keep the button pressed until the CAN
LED flashes then stays on. At this point the
Ethernet settings will have been restored to
defaults.
• After setting to factory defaults, the
IP address of the device will revert to
192.168.0.100
Once you have configured your PC’s IP
address, connect the EG2-NA directly to the
PC. It may be necessary to use a crossover
cable, however, most current computers are
able to connect directly to another Ethernet
device using a standard Ethernet cable.
iCANsoft will be used for the configuration
process. Open iCANsoft, then select from
the Toolbar Tools>Options>Network. Select
the Ethernet Gateway option and change the
IP Address to 192.168.0.100. Ensure that the
‘Use Password’ check box is ticked and the
default password: Cooper123 is entered (case
sensitive).
Select OK to confirm.
Search the network and load the EG2-NA into
iCANsoft. Follow the steps outlined in the PC
Node Method section to configure the desired
IP Address for the EG2-NA.
Once the IP Address settings have been
applied, initialize the new settings in the
EG2-NA device by pressing the reset button
next to the Ethernet conneciton or by
disconnecting and reapplying power.
Once configuration is complete, if you will
be using iCANsoft through the ethernet
connection, you will need to update the IP
Address in the Toolbar Tools>Options>Network
section to match the settings you have
assigned to the unit. This screen will also
allow you to re-select the option for PC Node
to allow for direct PC Node access for this
database.
Factory Default IP Settings
• IP Address 192.168.0.99
• Subnet Mask 255.255.255.0
• Gateway 192.168.0.1

Document: EG2-NA 9850-000225-02
Eaton Lighting Systems
Usk House, Lakeside, Llantarnam Park,
Cwmbran, NP44 3HD. UK
T: [phone] F: [phone]
E: [email protected] EatonLightingSystems.com
iLight Support
(International)
20 Greenhill Crescent,
Watford Business Park,
Watford, Herts,
WD18 8XG. UK
T: [phone]
(available Mon-Fri 9am-5pm GMT)
www.iLight.co.uk
Tec[email protected]
iLumin Support
(North America)
1121 Highway 74 South
Peachtree City, GA 30269
P: 770-486-4800
(Canada)
5925 McLaughlin Road
Mississauga, Ontario L5R 1B8
P: 905-501-3000
www.eaton.com/lighting
All products manufactured by Eaton Lighting Systems and identified with the iLight or iLumin
product series mark are warranted to be free from defects in material and workmanship and shall
conform to and perform in accordance with Seller’s written specifications.
This warranty will be limited to the repair or replacement, at Seller’s discretion, of any such goods
found to be defective, upon their authorized return to Seller. This limited warranty does not apply
if the goods have been damaged by accident, abuse, misuse, modification or misapplication, by
damage during shipment or by improper service.
There are no warranties, which extend beyond the hereinabove-limited warranty,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE
IMPLIED WARRANTY OF FITNESS.
No employee, agent, dealer, or other person is authorised to give any warranties on behalf of the
Seller or to assume for the Seller any other liability in connection with any of its goods except in
writing and signed by the Seller. The Seller makes no representation that the goods comply with
any present or future federal, state or local regulation or ordinance. Compliance is the Buyer’s
responsibility.
The use of the Seller’s goods should be in accordance with the provision of the National Electrical
Code, UL and/or other industry or military standards that are pertinent to the particular end use.
Installation or use not in accordance with these codes and standards could be hazardous.
!
WARNING HAZARDOUS VOLTAGES
DISCONNECT FROM SUPPLY
BEFORE REMOVING COVERS
NO USER SERVICEABLE PARTS INSIDE
SERVICE BY QUALIFIED PERSONNEL ONLY
WARNING
To reduce the risk of fire or electric shock,
DO NOT expose this device to rain or moisture.
DO NOT energise unless the front cover is in place.
This device must be earthed.
Installation, programming and maintenance must be carried out by qualified personnel.
Eaton Lighting Systems cannot accept responsibility for repairs or modifications that are not
competently executed and in accordance with service or upgrade information.
CE compliant to all relevant standards