Eaton CoviO User manual

INS #
Brand Logo
reversed out of
black
INS #
IL504001EN
Installation Instructions – CoviO Linear Cove System
#
#
Risk of Fire, Electrical Shock, Cuts or other Casualty Hazards- Installation and maintenance of this
product must be performed by a qualified electrician. This product must be installed in accordance
with the applicable installation code by a person familiar with the construction and operation of
the product and hazards involved.
Risk of Fire and Electric Shock- Make certain power is OFF before starting installation or
attempting any maintenance. Disconnect power at fuse or circuit breaker.
Risk of Fire- Minimum 90°C supply conductors.
Risk of Burn- Disconnect power and allow fixture to cool before handling or servicing.
Risk of Personal Injury- Due to sharp edges, handle with care.
Failure to comply with these instructions may result in death, serious bodily injury and property
damage.
WARNING
DISCLAIMER OF LIABILITY: Eaton assumes no liability for damages or losses of any kind that may arise from the
improper, careless, or negligent installation, handling or use of this product.
IMPORTANT: Read carefully before installing fixture. Retain for future reference.
NOTICE: Green ground screw provided in proper location. Do not relocate.
NOTICE: Fixture may become damaged and/or unstable if not installed properly.
ote:N Specifications and dimensions subject to change without notice.
ATTENTION Receiving Department: Note actual fixture description of any shortage or noticeable damage on
delivery receipt. File claim for common carrier (LTL) directly with carrier. Claims for concealed damage must be
filed within 15 days of delivery. All damaged material, complete with original packing must be retained.
io Lighting

32 EATON IL504001EN Installation instructions EATON IL504001EN Installation instructions
Installation Instructions – CoviO Linear Cove SystemInstallation Instructions – CoviO Linear Cove System
INSTALLATION
1. Optimize cove design detials.
ote:N To optimize cove lighting, cove design must be
optimized.
Figure 1.
Figure 2.1
Figure 2.2
Figure 3
Figure 4
Figure 5
Figure 6.1
Figure 6.2
Table 1.
1.7”
42 mm
Upper mounting
channel
Bottom mounting
channel
Female connector
Male Connector Female Connector
Beginning of Run Power Connection
Should Follow Wiring Chart Above
Line Voltage
Power Feed
(By Others)
15 degree
mount
30 degree
mount
Beginning
of Run
Power Cord
2. Plan run lengths and power drops per run
lengthspecifications below:
3. Unpack fixtures, cables, and mounting hardware from
boxes.
ote:N All installations require a beginning of run power cord
with custom connector and junction box supplied by
Eaton. Line voltage power supply line supplied by
others. If your installation calls for the jumper cable
accessory to add space between fixtures, make sure
they are available.
1.8”
46 mm
12” / 24”
305 mm / 610 mm
1.8”
46 mm
4. Prepare beginning fixture for line voltage input by
removing top screws to Wiring chart to be verified by
eng’g open junction box wiring compartment. Remove
cover of desired feed location and feed line voltage
power lead cable (by others) through hole. Trim power
feed to desired length. Connect power lead cable and
input driver wiring to female connector wires via wire
nuts. Green ground screw must be connected for safe
operation.
ote:N Minimum of 18 AWG power lead cable wires to be
used.
5. Close junction box by tightening top screws.
Beginning
of Run
Power Cord
Beginning
of Run
Junction
Box
Line Voltage
Power Feed
(By Others)
Beginning
of Run Male
Connector
WIRING CHART
* Fixtures utilize a Green Pigtail or a Green Through Wire for grounding.
HOT NEUTRAL GROUND * CONTROL 1 CONTROL 2
Black White Green Purple Gray
6. Secure mounting clips with 2 screws in straight line at
least 2” from wall for optimal cove lighting.
Connector
Location
Fixture
Release Tab
Fixture
Mounting
Location
Mounting
Holes
Top Mounting
Clip
Bottom
Mounting Clip
Mounting Stop
For Vertical
Mount
7. If mounting angle is desired, place proper degree
mounting under the clip.
8. Snap male connector from beginning of run power feed
into female connector of the first fixture in the run.
Self closing cap of female connector must be opened
for connection. Connector must “click” to ensure
complete, proper connection.
Cove face and shield
2” (min.)
Fixture distance from
back of cove wall
6” (min.)
Distance from
ceiling plane
Align
CoviO Installation Run Length Specications
Fixture Length
(Total Lumen Output)
1F=12"
(500lm)
Lumen Package 05L
(500lm/ft)
10L
(1000lm/ft)
15L
(1500lm/ft)
Fixture Input Wattage 5.2W 10.2W 14.6W
Dimming
Protocol
0-10V (STD)
ELV (ELV)
Triac (TR)
WaveLinx (WL)
Maximum Interconnect
Qty (PCS) @ 120V 140 70 50
Maximum Interconnect
Qty (PCS) @ 277V 300 170 120
DALI (5LT)
Maximum Interconnect
Qty (PCS) @ 120V 92 47 32
Maximum Interconnect
Qty (PCS) @ 277V
216 110 76
Fixture Length
(Total Lumen Output)
2F=24”
(3000lm)
Lumen Package 05L
(500lm/ft)
10L
(1000lm/ft)
15L
(1500lm/ft)
Fixture Input Wattage 10.2W 19.0W 28.9W
Dimming
Protocol
0-10V (STD)
ELV (ELV)
Triac (TR)
WaveLinx (WL)
Maximum Interconnect
Qty (PCS) @ 120V
70 35 25
Maximum Interconnect
Qty (PCS) @ 277V
170 85 60
DALI (5LT)
Maximum Interconnect
Qty (PCS) @ 120V
46 25 16
Maximum Interconnect
Qty (PCS) @ 277V
110 59 38

54 EATON IL504001EN Installation instructions EATON IL504001EN Installation instructions
Installation Instructions – CoviO Linear Cove SystemInstallation Instructions – CoviO Linear Cove System
To disconnect, squeeze the silver tab on the male connector pull apart fixtures.
Figure 7
Figure 8
Figure 9.1 Figure 9.2
9. Mountings are designed to span between fixtures to assure alingnment between fixtures within the cove. Connectors
have 2” standoffs to align with the cove wall and optimize cove lighting performance.
2”
10. Install fixture into mounting by making sure mounting channel in the bottom of the fixture engages with the mounting
clip.
Fixture can then be rotated into place making sure the top clip engages in the upper mounting channel to secure fixture in
any orientation.
Fixture should touch
Mounting Stop
AA
Brackets should be placed at either 12” or
24” on center spacing , depending on fixture
length (Dimension A)

Eaton
1121 Highway 74 South
Peachtree City, GA 30269
P: 770-486-4800
www.eaton.com/lighting
Canada Sales
5925 McLaughlin Road
Mississauga, Ontario L5R 1B8
P: 905-501-3000
F: 905-501-3172
© 2019 Eaton
All Rights Reserved
Printed in USA
Imprimé aux États-Unis
Impreso en los EE. UU.
Publication No. IL504001EN
May 24, 2019
Eaton is a registered trademark.
All trademarks are property
of their respective owners.
Eaton est une marque de commerce
déposée.Toutes les autres marques
de commerce sont la propriété de leur
propriétaire respectif.
Eaton es una marca comercial
registrada.Todas las marcas
comerciales son propiedad de sus
respectivos propietarios.
Product availability, specifications,
and compliances are subject to
change without notice
La disponibilité du produit, les
spécifications et les conformités
peuvent être modifiées sans préavis
La disponibilidad de productos, las
especificaciones y los cumplimientos
están sujetos a cambio sin previo aviso
Warranties and Limitation of Liability
Please refer to www.eaton.com/LightingWarrantyTerms for our terms and conditions.
Garanties et limitation de responsabilité
Veuillez consulter le site www.eaton.com/LightingWarrantyTerms pour obtenir les conditions générales.
Garantías y Limitación de Responsabilidad
Visite www.eaton.com/LightingWarrantyTerms para conocer nuestros términos y condiciones.
FCC Statement
•This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1)This device may not cause harmful interference.
(2)This device must accept any interference received,
including
interference that may cause undesired operation.
Note: The grantee is not responsible for any changes or
modifications not expressly approved by the party responsible
for compliance. Such modifications could void the user’s
authority to operate the equipment.
Note: The equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation.This
equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
an on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
This device complies with FCC radiation exposure limits set
forth for an uncontrolled environment.This equipment must be
installed and operated in accordance with provided instructions
and the antenna(s) used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons.