Eaton ATHA Manual

IL01602001E For more information visit: www.eaton.com
Instructions for Manual Operation of
Horizontal Design Transfer Switches
Instruction Leaflet
Introduction
These supplemental instructions covering the manual operation of
horizontal design transfer switches are applicable to the following
transfer switch instruction books and transfer switch catalog
numbers:
I.B. ATS Catalog #
G003 ATHA
V003 ATH2
AG03 ATHM
WB01 ATHI
ATHS
NTHS
PPHX
Operation
To operate the switch manually or if breaker trips, unplug P3 from
S3 to disconnect the motor circuit. Turn and hold brake release
lever to "HOLD FOR MANUAL OPERATION" position, and then
rotate manual operator knob in either direction to move ATS into
desired position. Then let go of brake release lever for "AUTO-
MATIC OPERATION" (Figures 1 and 2).
NOTICE
IF A TRANSFER SWITCH WITH ANY KIND OF ELECTRICAL OPERAT-
ING CAPABILITIES IS TO BE OPERATED MANUALLY UTILIZING THE
MANUAL OPERATING HANDLE, IT IS STRONGLY RECOMMENDED
THAT THE TRANSFER MOTOR CIRCUIT FIRST BE ISOLATED. THIS IS
ACCOMPLISHED BY UNPLUGGING THE S3 PLUG MARKED MOTOR
DISCONNECT. IF, HOWEVER, A TRANSFER SWITCH IS SUPPLIED
WITH A FOUR POSITION SELECTOR SWITCH (OPTION 6H), IT CAN
BE TURNED TO THE "OFF" POSITION, MAKING IT UNNECESSARY TO
UNPLUG THE S3 PLUG. IN THE CASE OF THE AUTOMATIC TRANS-
FER SWITCH DESIGN, ANY ATTEMPT TO OPERATE THE MANUAL
HANDLE WITHOUT FIRST ISOLATING THE MOTOR CIRCUIT CAUSES
AN AUTOMATIC TRANSFER.
Figure 1. Horizontal Switch Shown in Automatic Operation
Position.
Figure 2. Horizontal Switch Being Manually Operated
Manual
Operator
Knob
Brake Release
Lever

Instruction Leaflet
Page 2 Effective: February 2017
Instructions for Manual Operation of
Horizontal Design Transfer Switches
© 2017 Eaton
All Rights Reserved
Printed in USA
Publication No. IL01602001E/TBG001354
February 2017
This instruction leaflet is published solely for information purposes
and should not be considered all-inclusive. If further information
is required, you should consult Eaton.
Sale of the product(s) shown in this literature is subject to terms
and conditions outlined in appropriate Eaton selling policies or
other contractual agreements between the parties. This literature
is not intended to and does not enlarge or add to any such con-
tract. The sole source governing the rights and remedies of any
purchaser of this equipment is the contract between the pur-
chaser and Eaton.
NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WAR-
RANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MER-
CHANTABILITY, OR WARRANTIES ARISING FROM COURSE OF
DEALING OR USAGE OF TRADE, ARE MADE REGARDING THE
INFORMATION, RECOMMENDATIONS AND DESCRIPTIONS CON-
TAINED HEREIN. In no event will Eaton be responsible to the pur-
chaser or user in contract, in tort (including negligence), strict
liability or otherwise for any special, indirect, incidental or conse-
quential damage or loss whatsoever, including but not limited to
damage or loss of use of equipment, plant or power system, cost
of capital, loss of power, additional expenses in the use of exist-
ing power facilities, or claims against the purchaser or user by its
customers resulting from the use of the information, recommen-
dations and description contained herein.
CSA is a registered trademark of the Canadian Standards Associa-
tion. National Electrical Code and NEC are registered trademarks
of the National Fire Protection Association, Quincy, Mass. NEMA
is the registered trademark and service mark of the National Elec-
trical Manufacturers Association. Uniform Building Code (UBC) is
a trademark of the International Conference of Building Officials
(ICBO). UL is a federally registered trademark of the Underwriters
Laboratories Inc.
Eaton
Electrical Group
1000 Eaton Boulevard
Cleveland, OH 44122
United States
877-ETN CARE (877-386-2273)
Option 2, option 4, and then
option 3
Eaton.com