Eaton Powerware 3105 UPS User manual

Powerware 3105 UPS
USER'S MANUAL
Features:
SAFETY INSTRUCTIONS
1122
3344
INSTALLATION AND OPERATION:
The Powerware 3105 uninterruptible power system (UPS) protects your
sensitive electronic equipment from basic power problems such as power
failures, power sags, power surges, and line noise.
Eight outlets
-Four with surge and battery backup protection
-Four with surge protection only
Data Line (InternetfaxmodemDSL) or telephoneline surge protection jacks
Cold Start capability
Proprietary LanSafe Powermanagement software
User-replaceable batteries
Built-in USB communicationport
Compact design fits on/under your desk; can also be mounted to a wall
Convenient transformer block spacing
ATTENTION: Maintenance must be performed by a qualified personnel. Failure
to do so could result in an electric shock. Replace Battery with Powerware
supplied Battery ONLY! Although the unit may be unplugged from utility power,
hazardous voltage still may bepresent through the battery.
BATTERY CONNECTION REQUIRED BEFORE USE!
Connecting the Battery:
350VAand 500VA models(12V-5AH battery)
Push the topcenter Edge ofbattery cover
forward and removethe battery cover
Pull out the battery onto a flat, stable surface
and connect theblack battery cable to the
battery terminal
Reinstall the batteryinto the UPS Reinstall the batterycover
700VAmodel (12V-7AHbattery)
Push the topcenter Edge ofbattery cover
forward and removethe battery cover
Pull out thebattery onto aflat, stable
surface and connectthe black battery
cable to thebattery terminal
Reinstall the batteryinto the UPS Reinstall the batterycover
Installation and Operation:
Following steps explain how to connect and operate the Powerware 3105 UPS.
1. Connect the UPS toa grounded power outlet.
Note: It is recommended that the battery should be charged for minimum 8 hours
to ensure full charge before placing the UPS inservice.
2. Plug your computer, monitor or load to be protected into the “Battery Backup &
Surge Protection” outlets. (These outlets will provide emergency battery
backup power during power outages as well as protection from surges and
INDICATORS
Once you have received the Powerware 3105 UPS product, you should remove
and inspect the product for shipping damage. If any damage is found, please
notify the carrier and your dealer. Please keep the shipping carton and the
packing foam in the event the product must be returned to the factory for service.
1.Disconnect UPS system from power source.
2.Open battery door.
3.Disconnect used battery. Connect new battery. (It is important that
connectors be firmly attached to new batteries.)
4.Close battery door
5.Properly recycle used battery.
BATTERY REPLACEMENT PROCEDURE:
24
5
6
7
8
9
13
1.Place the Powerware 3105 UPS indoors in an area that has adequate airflow
and is freeof excessive dust. Do NOT allow the UPS to be exposedto
moisture, rain, excessiveheat, or direct sunlight.
2.Use ofthe Powerware 3105 UPS product in life support applications,where
failure of thisequipment can reasonably be expected to cause failure oflife
support equipment orto significantly affect its safety or effectiveness is NOT
recommended.
3.Disconnect the input power cord from the wall outlet before replacing the
battery.
4.When replacingthe battery, use the same number and type of battery
5.Do NOT dispose of battery in a fire. The battery may explode.
6.Do NOT open or mutilatethe battery. They contain an electrolytethat is toxic
and harmful tothe skin and eyes.
7.Proper disposal of the battery is required. Please refer to your local
laws/regulations regarding battery disposal.
8.Use tools with insulated handles to replace the battery to avoid personal
injury. Due to energyhazard, please remove wristwatches and jewelry such
as rings whenreplacing battery.
spikes.)
CAUTION: Do NOT plug LASER PRINTERS into the “Battery Backup” outlets.
CAUTION: Do NOT plug ACCESSORY SURGE strips into the “Battery Backup”
outlets.
3. Plug your peripheral equipment or non-critical loads (printer, scanner, fax,
speaker, etc.)into the “Surge Protection” outlets. (These outlets provide surge
and spike protection only, they will NOT provide battery backup power during a
utility power failure).
4. Connect yourcomputer to the UPS using USB cable provided.
5. With your equipment turned off, switch on the UPS.
6. When the “On/Off” LEDlight is illuminated, turn onthe connected equipment.
7. Install Power management software provided with the UPS
1.On/Off Push Button Switch
One switch controls the power to your equipment. Upon power turn on,
unit performs a self-test.
NOTE: Turn on the UPS
Press the push button switch locked in to turn on the UPS.
NOTE: Turn off the UPS
Press the push button switch again to turn off the UPS.
NOTE: Self-Test
The UPS performs a self-test for about 3 seconds when the UPS is
turned on.
2.On/Off Battery LED
Indicates the UPS is on and is powering your equipment.
A constantly illuminated LED indicates normal utility power operation.
A blinking LED indicates that the UPS is providing power from its battery.
3.Fault/Warning LED
Indicates a fault or warning condition is present.
A constantly illuminated LED indicates a fault or output SHORT condition.
A blinking LED indicates the UPS is overloaded or BAD battery condition.
4.Battery Backup & Surge Protection Outlets
Four 5-15R output receptacles that provide both battery backup and
surge protection.
5.Surge Protection Outlets
Four 5-15R output receptacles that provide surge and spike protection.
6.Data /Phone/Fax Protection Connectors
RJ11/RJ45
7.USB Communication Port
The provided LanSafe monitoring and shutdown software can be
automatically configured to save your files and shut down your
computer in the event of a prolonged power outage. Your personal
computer can receive the status of utility power line, utility power failure,
on battery and low battery by contact closure signals that are
sent through the USB port.
8.Circuit Breaker (resetable)
The button protrudes when an overload condition occurs. If the button
protrudes, disconnect some non-essential equipment and reset the
circuit breaker by pushing the button inward.
9. Power Cord
5-15P plug type attached - 6 foot line cord
112233
445566
778899
350VAand 500VA models(12V-5AH battery)
All manuals and user guides at all-guides.com
all-guides.com

112233
445566
778899
SPECIFICATIONS
Model Numbers
350 VA /210W
500 VA /300W
700 VA /420W
Capacity
TROUBLESHOOTING
Symptom Possible Cause Action to Take
UPS will not turn on
SERVICE AND SUPPORT
For questions and/or problems, please call your local distributor or the
help desk at one of the following telephone numbers and ask for a UPS technical
representative.
United States: 1.800.356.5737
Europe, Middle East, and Africa: +44.17.53.608.700
Asia: +852.2830.3030
Australia: +61.3.9706.5022
MA6B411002A(2005/01/25)
700VAmodel (12V-7AH battery)
STATUS INDICATORS:
The UPS provides both visual and audible status indicators. Visual
indicators consist of two LEDs to represent the following conditions:
On utility power operation
On battery power operation
UPS fault/alarm
LED & Alarm Status Table
UPS Status Green LED Red LED Buzzer
Self-test
AC
(Utility)
Mode
DC
(Battery)
Mode
Charging
Charge Off
Low Battery (Self-test)
Over Load
Normal
Over Load
Low Battery
Short / Fault
Over-Battery / Battery Fault
Blink 1(by turns)
ON
ON
ON
ON
ON
Blink 2
Blink 2
Blink 2
X
X
XX
XX
X
Blink 2
Blink 2
Blink 2
Blink 2
Blink 2
B1
B2
B4
B1
B4
B3
ON
B5
Notes:
Blink 1: ON 0.5 seconds / OFF 0.5 seconds.
Blink 2: ON 0.25 seconds / OFF 0.25 seconds.
B1: 1 beep / 5 seconds, ON 0.25 seconds / OFF 4.75 seconds.
B2: 3 beeps / 30 seconds, ON 0.25 seconds / OFF 0.25 seconds 3 times, 28.5 seconds OFF.
PW3105 350
PW3105 500
PW3105 700
Nominal Input Voltage
Nominal Output Voltage
Frequency
Total8 Outlets
120Vac
120Vac
50 / 60Hz auto sensing
4 Battery Backup& Surge Protection
4 Surge Protectiononly
Lighting / SurgeProtection
Transfer Time to Battery/AC
Battery Type
320 Joules
6ms Typical
Maintenance free, Sealedand leak proof lead-acid
battery
350 / 500VA: 12V 5AH
750 VA: 12V 7 AH
Battery Specification
Typical BackupTime
Internet / Phone/ Fax Protection
Short Circuit Protection
Communication Port
Operating Temperature
Operating Relative Humidity
Storage Temperature
Net Weight
3 minutes minimumat full rated load
RJ11/RJ45
Circuit Breaker
USB
0 C to 40 C
0 to 95%non-condensing
-15 C to 50C
350VA-9.5 pounds / 4.3 kg
500VA-11.7 pounds /5.3kg
700VA-14.3 pounds / 6.5kg
Dimensions (W xD x H) 11 x 7 x 4.4 i n.
* Due tocontinuing product improvement programs, specifications subject to change
without notice.
The battery is disconnected
or utility power is not
available at the wall outlet.
Input Circuit Breaker has
tripped.
Connect the battery (see Connect
Battery) and ensure power is
available at the wall outlet.
Reduce the amount of equipment
plugged into the outlets of the UPS.
Next, reset the circuit breaker by
pushing the plunger back in.
UPS is making a
continuous sound and
the “Overload” indicator
is lighted.
Turn off the UPS and reduce the
amount of equipment connected to
these outlets.
The “Battery Backup &
Surge Protection” outlets
are overloaded.
Removed all connected equipments
from the UPS and charge the battery
at least 8 hours. During this charging
period, turn off the UPS to prevent
unnecessary discharging.
Call for service or you can replace
the battery by ordering one from
your dealer.
The battery isnot fully
charged.
Battery is gettingolder.
UPS does notprovide
expected runtime.
Reduce the amount of equipment
plugged into the outlets of the UPS.
Try reducing the load by removing
one piece of equipment at a time to
determine if the problem continues.
The UPS willturn off when the
battery has beendepleted during
an extended poweroutage. Allow
the UPS tore-charge the battery,
before continuing onbattery opera
tion.
Ensure the equipment that is to be
protected from a power outage is
plugged into the “Battery Backup &
Surge Protection” outlets.
Contact Powerware Technical
Support
The UPS isoverloaded.
The UPS hasexhausted
its available runtime.
Equipment is connected
to the “surgeProtection”
outlets.
The UPS mayrequire
service.
Please have thefollowing information ready when you callthe Help Desk:
Model number and Serial number
Symptoms of failure or problem
Customer return address and contact information
If repair isrequired, you will be given a Returned Material Authorization (RMA)
Number. This number must appear on the outside of the package and on the Bill
of Lading (if applicable). Use the original packaging or request packaging from
the Help Desk or distributor. Units damaged in shipment as a result of improper
packaging are not covered under warranty. Areplacement unit will be shipped,
freight prepaid forall units under warranty
For additional information please visit us online: www.powerware.com
B3: 2 beeps/ 5 seconds, ON, 0.25 seconds / OFF 0.25 seconds 2 times, 4 seconds OFF.
B4: ON 0.5seconds / OFF 0.5 seconds.
B5: 3 beeps/ 5 seconds, ON 0.25 seconds / OFF 0.25 seconds 3 times, 3.5 seconds OFF.
When utility powerfails,
connected equipment
loses power
All manuals and user guides at all-guides.com