Ebyte E104-BT40-TB User manual

E104-BT40-TB User Manual v1.0
1. Introduction
1.1 Feature introduction
E104-BT40-TB backplane adopts USB interface, which can quickly test the
E104-BT40 Bluetooth related features and functions.
1.2 Electrical parameters
No.
Parameter name
Parameter value
Comment
1
Support module
E104-BT40
Dual-mode Bluetooth to serial port
module
2
Module process
With USB connector
3
Production process
Lead-free process, SMT
Batch consistency and reliability are
ensured via SMT

4
Power supply interface
USB or external power
supply
-
5
Communication Interface
USB
6
Operating temperature
-40~+85℃
Industrial grade
7
Operating humidity
10%~90%
Relative humidity, non-condensing
8
Storage temperature
-40~+125℃
Industrial grade
2.Function description
2.1 Pin definition

Pin No.
Pin name
Pin
direction
Use
1
VBAT
Input
External 3.3V power supply
2
USB
Input
USB 5V power supply
3
+5V
Input
External 5V power supply, same as USB
4
RESET
Input
Reset pin
5
P10
Input
Test the P10 pin, press it for low level
6
VCC
-
Two alternative power supply modes: USB / 5V and VBAT
7
RX
Input
Serial data input
8
TX
Output
Serial data output
9
PWM2
Output
Output PWM2, connected to PWM LED
10
DISC
Input
Default pull-up input, the jumper cap is connected, and a
falling edge is generated, that is, the connection is
disconnected
11
MODE
Input
Low level switches to AT command mode, high level
switches to data transparent transmission mode (effective
when connected)）
2.2 Function test
Test function
Description
Transparent
transmission
test
The module acts as a slave, and a mobile phone, computer or other host module acts as a
master to establish a Bluetooth master-slave connection to achieve transparent data
transmission.
1. The module is connected to the computer USB. The 6-pin jumper cap is selected to be
powered by USB. The 7-pin-RX and 8-pin-TX pins are respectively shorted with jumper
caps, MOD, DISC is floating;
2. The module is connected to the computer USB interface, the power indicator is always
on, the STAT indicator flashes at 1HZ, and the module is powered on normally. The module
automatically enters the broadcast (BLE) or query scan status (SPP). After the host initiates
the connection and establishes the connection, the STAT and LINK LED are always on,
indicating that the Bluetooth connection is successful.
3. Open the serial port, the default baud rate is 115200, the data bit is 8, 1 stop bit, no parity
bit, no flow control.
Disconnect
1. Establish a Bluetooth connection by according to transparent transmission test.
2. After the module is connected, the jumper cap is shorted to pin 10, that is, DISC, and the
connection is disconnected
Parameter
modification
1.The module is in the configuration mode when it is not connected, and the MODE pin is
left floating.
2. Pull the MODE pin low to establish a connection and at this time it is in AT command

mode.
3. The MODE pin is left floating. After the module is connected, pull the MODE pin low
and wait for about 200ms before the module enters the AT command mode; Pull the MODE
pin high and wait for about 200ms, the module exits the AT command mode and switches to
transparent transmission mode(MODE pin takes effect after connection)
4. After the module is disconnected, it is also in AT command mode
PWM test
Module is powered on, for example: AT + PWM2 = 100 command sets PWM2 output,
observe that PWM LED is always on; AT + PWM2 = 50, PWM LED 1HZ frequency
flashes
IO input test
The module is powered on, and this is the configuration mode. Send the command AT +
P10 ?, the default result is high level, press the key corresponding to pin 5 and send the
above command at the same time, the result is low level.
About us
Technical support: [e-mail]
Documents and RF Setting download link:：https://www.cdebyte.com
Thank you for using Ebyte products! Please contact us with any
questions or suggestions: [e-mail]
Official hotline:[phone]
Web: https://www.cdebyte.com
Address: B5 Mould Park, 199# Xiqu Ave, High-tech District,
Sichuan, China