Ebyte E01-ML01DP4 User manual

[
E01-ML01DP4 User Manual
nRF24L01P 2.4GHz 100mW DIP wireless module

Chengdu Ebyte Electronic Technology Co., Ltd. E01-ML01DP4 User Manual
Copyright ©2012–2018，Chengdu Ebyte Electronic Technology Co.,Ltd 1
目录
1. Overview............................................................................................................................................................................ 2
1.1 Brief introduction..................................................................................................................................................... 2
1.2 Features.....................................................................................................................................................................2
1.3 Application............................................................................................................................................................... 2
2. Specification and parameter............................................................................................................................................... 3
2.1 Limit parameter........................................................................................................................................................ 3
2.2 Operating parameter................................................................................................................................................. 3
3. Size and pin definition........................................................................................................................................................4
4. Basic operation................................................................................................................................................................... 5
4.1 Hardware design................................................................................................................................................ 5
4.2 Software editing........................................................................................................................................................6
5. Basic application................................................................................................................................................................ 6
5.1 Basic circuit diagram................................................................................................................................................ 6
6. FAQ.................................................................................................................................................................................... 6
6.1 Communication range is too short............................................................................................................................6
6.2 Module is easy to damage........................................................................................................................................ 7
6.3 BER(Bit Error Rate) is high..................................................................................................................................... 7
7. Production guidance........................................................................................................................................................... 7
8. E01 Series...........................................................................................................................................................................7
9. Packing............................................................................................................................................................................... 8
9.1 Anti-statistic pallet....................................................................................................................................................8
Revision history......................................................................................................................................................................8
About us..................................................................................................................................................................................9

Chengdu Ebyte Electronic Technology Co., Ltd. E01-ML01DP4 User Manual
Copyright ©2012–2018，Chengdu Ebyte Electronic Technology Co.,Ltd 2
1. Overview
1.1 Brief introduction
E01-ML01DP4 is a DIP module based on original
imported nRF24L01P form Nordic in Norway, operates at
2.4Ghz with PCB antenna.
The RF performance of E01-ML01DP4 and components
selection during R&D are all in accordance with industrial
grade standards, using industrial-grade high-precision 16MHz
crystal oscillator, also it obtained FCC, CE and RoHS
certification. A power amplifier (PA) and a low noise amplifier
(LNA) are built in, so that the maximum transmit power
reaches 100mW and the receiving sensitivity is further
improved. The products have been greatly improved when there is no PA and LNA in design.
The user needs to use the MCU driver or use a dedicated SPI debugging tool to develop E01-ML01DP4.
1.2 Features
Communication distance tested is up to 1.8KM；
Maximum transmission power of 100mW, software multi-level adjustable;
Support air date rate of 2Mbps, 1Mbps, 250kbps;
125 communication channels to meet the needs of multi-point communication, grouping, frequency hopping, etc.
Connect to the MCU through the SPI interface at a rate of 0 to 10 Mbps.
Support 2.0V~3.6V power supply, power supply over 3.3V can guarantee the best performance；
Industrial grade standard design, support -40 ~ 85 °C for working over a long time；
PCB antenna;
Enhanced ShockBurst, fully compatible with NORDIC all nRF24L, nRF24E, nRF24U series.
1.3 Application
Wearable device；
Smart home and industrial sensors；
Security system, positioning system；
Wireless remote control, drone；
Wireless game remote control；
Healthcare products；
Wireless voice, wireless headset；
Automotive industry applications.

Chengdu Ebyte Electronic Technology Co., Ltd. E01-ML01DP4 User Manual
Copyright ©2012–2018，Chengdu Ebyte Electronic Technology Co.,Ltd 3
2. Specification and parameter
2.1 Limit parameter
Main parameter
Performance
Remark
Min.
Max.
Power supply（V）
0
3.6
Voltage over 3.6V will cause
permanent damage to module
Blocking power（dBm）
-
10
Chances of burn is slim when modules
are used in short distance
Operating temperature（℃）
-40
85
-
2.2 Operating parameter
Main parameter
Performance
Remark
Min.
Typ.
Max
Operating voltage（V）
2.0
3.3
3.6
≥3.3V ensures output power
Communication level（V）
-
3.3
-
For 5V TTL, it may be at risk of
burning down
Operating temperature（℃）
-40
-
85
Industrial design
Operating frequency（MHz）
2.4
-
2.525
Support ISM band
Power
consumption
TX current（mA）
-
110
-
Instant power consumption
RX current（mA）
-
20
-
-
Sleep current （μA）
-
1.0
-
Software is shut down
Max Tx power（dBm）
19.7
20
20.2
-
Receiving sensitivity（dBm）
-95.5
-96
-97.5
Air data rate is 250kbps
Air data rate（bps）
250k
-
2M
Controlled via user’s programming
Main parameter
Description
Remark
Distance for reference
1800m
Test condition：clear and open area, antenna gain: 5dBi，antenna height: 2.5m，
air data rate: 250kbps
FIFO
32Byte
Max length transmitted each time
Crystal frequency
16MHz
-
Modulation
GFSK
-
Package
DIP
-
Connector
2.54mm pin
-
Communication interface
SPI
0-10Mbps
Size
15 * 27mm
Without SMA
Antenna
PCB antenna
50ohm impedance

Chengdu Ebyte Electronic Technology Co., Ltd. E01-ML01DP4 User Manual
Copyright ©2012–2018，Chengdu Ebyte Electronic Technology Co.,Ltd 4
3. Size and pin definition
Pin No.
Pin item
Pin direction
Pin application
1
GND
-
Ground
2
VCC
-
Power supply must be 20. ~ 3.6V
3
CE
Input
Chip Enable
4
CSN
Input
SPI Chip select
5
SCK
Input
SPI clock
6
MOSI
Input
SPI master output slave input
7
MISO
Output
SPI master input slave output
8
IRQ
Output
Interrupt request.

Chengdu Ebyte Electronic Technology Co., Ltd. E01-ML01DP4 User Manual
Copyright ©2012–2018，Chengdu Ebyte Electronic Technology Co.,Ltd 5
4. Basic operation
4.1 Hardware design
5 It is recommended to use a DC stabilized power supply. The power supply ripple factor is as small as possible, and
the module needs to be reliably grounded；
6 Please pay attention to the correct connection of the positive and negative poles of the power supply. Reverse
connection may cause permanent damage to the module；
7 Please check the power supply to ensure it is within the recommended voltage otherwise when it exceeds the
maximum value the module will be permanently damaged;
8 Please check the stability of the power supply, the voltage cannot be fluctuated frequently；
9 When designing the power supply circuit for the module, it is often recommended to reserve more than 30% of the
margin, so the whole machine is beneficial for long-term stable operation;
10 The module should be as far away as possible from the power supply, transformers, high-frequency wiring and other
parts with large electromagnetic interference;
11 High-frequency digital routing, high-frequency analog routing, and power routing must be avoided under the
module. If it is necessary to pass through the module, assume that the module is soldered to the Top Layer, and the
copper is spread on the Top Layer of the module contact part(well grounded), it must be close to the digital part of
the module and routed in the Bottom Layer；
12 Assuming the module is soldered or placed over the Top Layer, it is wrong to randomly route over the Bottom Layer
or other layers, which will affect the module's spurs and receiving sensitivity to varying degrees；
13 It is assumed that there are devices with large electromagnetic interference around the module that will greatly
affect the performance. It is recommended to keep them away from the module according to the strength of the
interference. If necessary, appropriate isolation and shielding can be done；
14 Assume that there are traces with large electromagnetic interference (high-frequency digital, high-frequency analog,
power traces) around the module that will greatly affect the performance of the module. It is recommended to stay
away from the module according to the strength of the interference. If necessary, appropriate isolation and shielding
can be done.
15 If the communication line uses a 5V level, a 1k-5.1k resistor must be connected in series (not recommended, there is
still a risk of damage)；
16 Try to stay away from some physical layers such as TTL protocol at 2.4GHz , for example: USB3.0；
17 The mounting structure of antenna has a great influence on the performance of the module. It is necessary to ensure
that the antenna is exposed, preferably vertically upward. When the module is mounted inside the case, use a good
antenna extension cable to extend the antenna to the outside；
18 The antenna must not be installed inside the metal case, which will cause the transmission distance to be greatly
weakened.
19 Conductors or other sources of interference should be avoided around the onboard PCB antenna.

Chengdu Ebyte Electronic Technology Co., Ltd. E01-ML01DP4 User Manual
Copyright ©2012–2018，Chengdu Ebyte Electronic Technology Co.,Ltd 6
4.2 Software editing
This module is nRF24L01+PA+LNA, the drive mode is exactly equivalent to nRF24L01P, the user can operate
according to the nRF24L01P manual (Please see nRF24L01P manual for more details).
As interrupt pin for IRQ, it can be used to wake-up MCU and achieve fast response;
But the user can get the interrupt status through SPI (not recommended, it is not conducive to the overall power
consumption, and with low efficiency）.
CE pin can be high level for long-term, but it needs to set as POWER DOWN mode when the module write
registers, and it is recommended that CE is controlled by MCU pin.
Make sure the CE pin connect to LNA enable pin , when CE equal to 1, LNA is turned on, when CE to 0, LNA is
turned off. This operation is perfectly matched with the transceiver mode of nRF24L01; that is to say, users do not
have to care about the LNA operation
If the automatic response is needed, the CE pin must keep high level when transmitting, instead of keeping high
level time just more than 10us like the datasheet mentioned.The operation we recommended is: when CE equal to 1,
the module begin sending, after sending all, then make the CE equal to 0, instead of making the CE equal to 0 after
10 us.The reason is: the module turns into receiving mode immediately after sending L01P,If CE equal to 0,it means
LNA closed, will not be beneficial to the receiving senility
5. Basic application
5.1 Basic circuit diagram
6. FAQ
6.1 Communication range is too short
The communication distance will be affected when obstacle exists.
Data lose rate will be affected by temperature, humidity and co-channel interference.

Chengdu Ebyte Electronic Technology Co., Ltd. E01-ML01DP4 User Manual
Copyright ©2012–2018，Chengdu Ebyte Electronic Technology Co.,Ltd 7
The ground will absorb and reflect wireless radio wave, so the performance will be poor when testing near ground.
Sea water has great ability in absorbing wireless radio wave, so performance will be poor when testing near the sea.
The signal will be affected when the antenna is near metal object or put in a metal case.
Power register was set incorrectly, air data rate is set as too high (the higher the air data rate, the shorter the
distance).
The power supply low voltage under room temperature is lower than 2.5V, the lower the voltage, the lower the
transmitting power.
Due to antenna quality or poor matching between antenna and module.
6.2 Module is easy to damage
Please check the power supply source, ensure it is 2.0V~3.6V, voltage higher than 3.6V will damage the module.
Please check the stability of power source, the voltage cannot fluctuate too much.
Please make sure antistatic measure are taken when installing and using, high frequency devices have electrostatic
susceptibility.
Please ensure the humidity is within limited range, some parts are sensitive to humidity.
Please avoid using modules under too high or too low temperature.
6.3 BER(Bit Error Rate) is high
There are co-channel signal interference nearby, please be away from interference sources or modify frequency and
channel to avoid interference;
Poor power supply may cause messy code. Make sure that the power supply is reliable.
The extension line and feeder quality are poor or too long, so the bit error rate is high;
7. Production guidance
This module is a DIP module, the workers must work according to the static discharge operation specifications
while welding. This module is a static-sensitive product, it may cause permanent damages if the module is not welded
according to the specifications.
8. E01 Series
Model No.
IC
Frequency
Tx power
Test
distance
Package
Antenna
Hz
dBm
km
E01-ML01S
nRF24L01P
2.4G
0
0.1
SMD
PCB
E01-ML01D
nRF24L01P
2.4G
0
0.1
DIP
PCB
E01-ML01IPX
nRF24L01P
2.4G
0
0.2
SMD
IPEX

Chengdu Ebyte Electronic Technology Co., Ltd. E01-ML01DP4 User Manual
Copyright ©2012–2018，Chengdu Ebyte Electronic Technology Co.,Ltd 8
E01-ML01DP4
nRF24L01P
2.4G
20
1.8
DIP
PCB
E01-ML01DP5
nRF24L01P
2.4G
20
2.5
DIP
SMA-K
E01-ML01SP2
nRF24L01P
2.4G
20
1.8
SMD
PCB/IPEX
E01-ML01SP4
nRF24L01P
2.4G
20
2
SMD
IPEX
E01-2G4M27D
nRF24L01P
2.4G
27
5
DIP
SMA-K
9. Packing
9.1 Anti-statistic pallet
Revision history
Version
Date
Description
Issued by
1.00
2017/11/15
Original version
huaa
1.10
2018/5/22
Content updated
huaa
1.20
2018/9/13
Model No. split
huaa

Chengdu Ebyte Electronic Technology Co., Ltd. E01-ML01DP4 User Manual
Copyright ©2012–2018，Chengdu Ebyte Electronic Technology Co.,Ltd 9
1.30
2019/12/21
Circuit diagram modification
Linson
About us
Technical support: suppo[email protected]
Documents and RF Setting download link: www.ebyte.com
Thank you for using Ebyte products! Please contact us with any questions or suggestions: [email protected]m
-------------------------------------------------------------------------------------------------
Fax: [phone] ext. 821
Web: www.ebyte.com
Address: Innovation Center D347, 4# XI-XIN Road,Chengdu, Sichuan, China