Ecco EC7008-WK2 User manual

Page 1 of 9
Installation Instructions
Wireless Camera/Monitor System
Installation, Wiring and Function
CAMERA SYSTEM MODEL EC7008-WK2
OPERATING INSTRUCTIONS:
MS
Digital Color LED Screen
Power
Menu
Record/Select Volume Decrease/Menu
Navigation
Volume Increase/Menu Navigation
Camera Channel Select
Dimming Sensor
Loudspeaker
U-Support Bracket Pedestal Mount Slot
Mini SD Card Slot
Remote
Control
Sensor
Ecante-5
Digital Color LCD Screen
Dimming Sensor
Camera Channel Select
Volume Increase/Menu Navigation
Volume Decrease/
Menu Navigation
Record/Select
Menu
Power
Remote
Control
Sensor
Ecante-5
Mini SD Card
Slot
Loudspeaker
U-Support Bracket Pedestal Mount Slot
IMPORTANT! Read all instructions before installing and using. Installer: This manual must be delivered to the end user.
WARNING!
Failure to install or use this product according to manufacturer’s recommendations may result in property damage, serious injury, and/
or death to those you are seeking to protect!
Do not install and/or operate this safety product unless you have read and understood the safety information
contained in this manual.
1. Proper installation combined with operator training in the use, care, and maintenance of emergency warning devices are essential to
ensure the safety of emergency personnel and the public.
2. Emergency warning devices often require high electrical voltages and/or currents. Exercise caution when working with live electrical
connections.
3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high current arcing,
which can cause personal injury and/or severe vehicle damage, including ¿re.
4. Proper placement and installation is vital to the performance of this warning device. Install this product so that output performance of
the system is maximized and the controls are placed within convenient reach of the operator so that they can operate the system without
losing eye contact with the roadway.
5. Do not install this product or route any wires in the deployment area of an air bag. Equipment mounted or located in an air bag
deployment area may reduce the e-ectiveness of the air bag or become a projectile that could cause serious personal injury or death. 
Refer to the vehicle owner’s manual for the air bag deployment area. It is the responsibility of the user/operator to determine a suitable
mounting location ensuring the safety of all passengers inside the vehicle particularly avoiding areas of potential head impact.
6. It is the responsibility of the vehicle operator to ensure daily that all features of this product work correctly. In use, the vehicle operator
should ensure the projection of the warning signal is not blocked by vehicle components (i.e., open trunks or compartment doors),
people, vehicles or other obstructions.
7. The use of this or any other warning device does not ensure all drivers can or will observe or react to an emergency warning signal.
Never take the right-of-way for granted. It is the vehicle operator’s responsibility to be sure they can proceed safely before entering an
intersection, drive against tra-c, respond at a high rate of speed, or walk on or around tra-c lanes.
8. This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obeying all laws
regarding emergency warning devices. Therefore, the user should check all applicable city, state, and federal laws and regulations. The
manufacturer assumes no liability for any loss resulting from the use of this warning device.
CAUTION!
When drilling into any vehicle surface, make sure that the
area is free from any electrical wires, fuel lines, vehicle
upholstery, etc. that could be damaged.

Page 2 of 9
WARNING!
1. Please align the remote control with the remote signal receiver window to operate.
2. Never disassemble the remote control or allow it to drop or get wet.
!
WIRING INSTRUCTIONS:
Notes:
1. Larger wires and tight connections will provide longer service life for components. For high current wires it is recommended
that terminal blocks or soldered connections be used with shrink tubing to protect the connections. Do not use insulation
displacement connectors (e.g., 3M Scotchlock type connectors)
2. Route wiring using grommets and sealant when passing through compartment walls. Minimize the number of splices to
reduce voltage drop. High ambient temperatures (e.g., under-hood) will signicantly reduce the current carrying capacity of
wires, fuses, and circuit breakers. All wiring should conform to the minimum wire size and other recommendations of the
manufacturer and be protected from moving parts and hot surfaces. Looms, grommets, cable ties, and similar installation
hardware should be used to anchor and protect all wiring.
3. Fuses or circuit breakers should be located as close to the power takeo󰀨 points as possible and properly sized to protect the
wiring and devices.
4. Particular attention should be paid to the location and method of making electrical connections and splices to protect these
points from corrosion and loss of conductivity.
5. Ground termination should be only be made to substantial chassis components, preferably directly to the vehicle battery.
6. Circuit breakers are very sensitive to high temperatures and will “false trip” when mounted in hot enviroments or operated
close to their capacity.
The unit is designed for electrical systems from 12 to 24 VDC (10 to 30 VDC extremes). Wiring options are as follows in Figure 1:
All wiring should be a minimum of 26 AWG. A 3-amp fuse in the positive line for the monitor is required.
EC7008-WK
Power(RED)
Ground(BLACK)
Camera #1 - Trigger Wire - Optional (GREEN)
SPLIT - Custom view over ride (YELLOW)
Camera 4 Trigger Wire - Optional (BROWN)
Camera 2 Trigger Wire - Optional (WHITE)
Camera 3 Trigger Wire - REVERSING CAMERA with B LInes (BLUE)
PCY-EC7008-WM
8 Pin
EC7008-WM
ECANTE-5
SD card (Keys provided)
ECANTE-5
Figure 1
Important! Waterproof all connections whether inside or outside the vehicle by using sealant and wrapping with insulation tape. Wrap tape tightly,
overlapping by one-half widths so there are no gaps.
*Trigger wire may or may not be required based on your specic application.
= no/low signal
= full signal and you are ready to go to next step
RECOMMENDED TO BENCH TEST PRIOR TO INSTALL to establish placement/priority for cameras.
1. Trim the solder tips to improve connections.
2. Install antenna(s) onto the monitor - twist on.
3. Connect the monitor power cord to the harness by lining up the notches to fully seat over the knob.
4. Power on the monitor by connecting the red to power and black to ground.
5. Monitor will default to H-split view.
6. Follow instructions for pairing to pair the cameras.
INSTALLATION INSTRUCTIONS:
Camera 4 Trigger Wire - Reversing Camera (BROWN)
Camera 3 Trigger Wire - (BLUE)
EC7008-WM2

Page 3 of 9
MONITOR PARTS IDENTIFICATION
OK
SEL
MENU
PAIR SYS MIR
VOL VOL
Press to enable or
disable mute
MUTE POWER
Press OK button to
enter menu item or
save user settings.
Press OK button -
shortcut for start/stop
recording
Volume decrease
and menu selection
left
Press to cycle
through camera
channels
Press to turn on/off
the monitor
Press to show menu
or exit menu
Volume increase
and menu selection
left
MIR - Flip selection
PAL/NTSC TV
system selector
Press to enter
pairing mode
Volume increase and
menu selection right
Jump key selector.
Fast jump to the
display mode
specied by SYSTEM
Menu Operation
• Press ‘M’ button on monitor or ‘menu’ button on remote control to show menu.
• Press ‘+’ or ‘- ‘button on monitor or VOL +/- on remote control to select sub-menu.
• Press button on monitor or ‘OK’ on remote control to enter sub-menu.
• Press ‘menu’ button again to return to the main menu.
Main Menu
Audio Source
• Select the channel that you want to hear the audio under split view mode.
• Press ‘+’ or ‘- ‘button on monitor or VOL +/- on remote control to switch option.
• Press on the monitor or ‘OK’ on the remote control to select the channel and exit the menu.

Page 4 of 9
Display Mode
• Select display mode.
• is auto-scan, automatically switch channel in circle from channel 1
through to .
• Press ‘+’or ‘- ’ button on monitor or VOL +/- on remote control to switch option.
Press on monitor or ‘OK’ on remote control to select the channel and exit
the menu.
Pairing
• Pairing Camera: select the channel you want to pair.
• Press ‘+’ or ‘- ‘button on monitor or VOL +/- on remote control to switch option.
• Press button on monitor or ‘OK’ on remote control to start pairing.
When pairing is in process, there will be pairing icon on top of the
correspondent channel.
Pairing icon will be replaced with a check mark when pairing is successful. If no
camera pairs successfully in 20 seconds, the pairing icon will disappear and the
pairing process will stop.
Delete Camera: remove the camera that is already paired to the selected channel.
Record Control
• Select to start and stop record.
• Press button on monitor to start record or stop record.
When camera is not connected, press record, a grey dot will appear on the top
left, and nothing will be recorded.
When camera is connected, press record, a red dot will appear on the top left,
and video is recorded.
Playback
Folder will be automatically increased as record les increase, one folder will
contain max. 997 video les, automatically create new folder when one folder is
full. The greater the le number, the newer the le, when SD card is full, will start
overwrite from the oldest le.
• Press ‘+’ or ‘- ‘button on monitor or VOL +/- on remote control to switch option.
• Press button on monitor or ‘OK’ on remote control to start playback.
Camera: show the channel that record le belongs to
Name: le name
Create: date and time that the le created
Group Num: group num increases every time start new record, les with same
group num are from the same record, eg: 4 channels recorded in quad view at the
same time, the four video les for each channel will have the same group num.
When playback le is recorded under split view, a window will appear to select
playback in multiple channel view or single channel view.

Page 5 of 9
Setting
Camera
Please note that these parameters can only be adjusted when camera is
connected to correspondent channel
• To select channel, press ‘M’ button on monitor or ‘Menu’ on remote control, when
the icon background turns green, press ‘+’ or ’-’ button on monitor or VOL +/- on
remote control to switch to the channel you want to set.
• Press button on monitor or ‘OK’ on remote control to enter the channel’s
parameter.
• Press ‘+’ or ’-’ button on monitor or VOL +/- on remote control to select the
parameter to change. A GREEN outline will show on the current selected
parameter.
• Press button on monitor or ‘OK’ on remote control to select the current
parameter. When the outline turns RED, Press (or long press) ‘+’ or ’-’ button on
monitor or VOL +/- on remote control to adjust value, press button on monitor
or ‘OK’ on remote control, cursor return to green.
• Press ‘M’ button on monitor or ‘Menu’ on remote control to return to select
channel.
• Press ‘M’ on monitor or ‘menu’ on remote control to save and exit menu.
Record
Currently displayed channels are indicated by green lettering. The new selection is
indicated by a green background.
• Press ‘+’ or ’-’ button on monitor or VOL +/- on remote control to switch on
options.
• Press button on monitor or ‘OK’ on remote control to select.
• Press ‘M’ on monitor or ‘menu’ on remote control to save and exit menu.
Record time: Record duration of each le.
Format SD card: It is suggested to format all SD card when rst time use on the
monitor.
Power on record: Start recording upon power on monitor.
System
Dimmer value can be adjusted only when Auto is o󰀨.
• Select to set day and night dimmer value.Press ‘M’ on monitor or ‘menu’
on remote control to save and exit menu.
Day: Adjust the panel brightness in normal light condition.
Night: Adjust the panel brightness in low light condition.
Dual View
• Set camera combination in dual view mode.
Currently displayed channels are indicated by green lettering. The new selection is
indicated by a green background.
• Press ‘+’ or ’-’ button on monitor or VOL +/- on remote control to switch channel
display in dual view.
• Press button on monitor or ‘OK’ on remote control to save selection.
Quad View and H View
Same way of operation as Dual View.
Trigger
Trigger Delay: Setting range is 1~60s, The trigger delay indicates how long it will
take after the trigger wire is disconnected, before the monitor goes back to the
original view.
Priority: Setting range is 1~5.
Trigger is in priority over auto scan
Support trigger under standby mode
Display: Set trigger to show specic view mode when yellow trigger wire is
activated.
AutoScan
Auto scan duration range is 5~60s, The duration indicates how long a camera
view will be shown when the monitor is set to auto scan, before cycling to the next
camera view. Each camera view can be turned on or o󰀨 to be included or removed
from the auto scan rotation.

Page 6 of 9
Power On
• Select the view you want to show upon power on.
Start auto scan upon power on.
Enter standby mode (black screen) upon power on.
Icon in green is the one currently selected.
• Press ‘+’ or ’-’ button on monitor or VOL +/- on remote control to switch option.
• Press button on monitor or ‘OK’ on remote control to cancel option, icon turns
white if option is canceled, when all options are white, monitor will show the
picture from the last time when it was powered o󰀨.
• Press ‘M’ on monitor or ‘menu’ on remote control to save and exit menu.
Parking Line
If set on, show reverse label upon trigger the correspondent channel.
• Enter setting to move the label.
• Press ‘+’ or ’-’ button on monitor or VOL +/- on remote control to move
the label right or left.
• Press ‘+’ or ’-’ button on monitor or VOL +/- on remote control to move
the label up or down.
• Press ‘+’ or ’-’ button on monitor or VOL +/- on remote control to
adjust size of label.
• Press button on monitor or ‘OK’ on remote control to switch mode.
Date & Time
• Select the correspondent icon to call up keyboard to set date and time.
• Press ‘+’ or ’-’ button on monitor or VOL +/- on remote control to switch to the
number that needs to be adjusted.
• Press button on monitor or ‘OK’ on remote control to call up keyboard.
• Press ‘+’ or ’-’ button on monitor or VOL +/- on remote control to select number
one by one.
• Select enter to conrm.
• Touch to select number, touch enter to exit and save.
 Power O-
• Select screen o󰀨 to enter standby mode, monitor will respond upon
trigger.
• Select sleep to enter sleep mode, monitor will not respond to trigger.
MONITOR MODEL EC7008-WM2
INSTALLATION AND MOUNTING:
WARNING!
To prevent accidental shock, DO NOT OPEN THE MONITOR CASE. Opening the monitor case will expose the inside of the monitor to conditions
that could adversely a-ect performance. Any evidence of tampering with sealed components will void the warranty.
Important! Do not expose the monitor to water, it is not waterproof. Any water that leaks into the monitor could cause extensive damage.
!
Carefully remove the unit from its packaging. Examine the unit for transit damage. If damage is found, return the product to your local dealer for war-
ranty replacement. Do not use damaged or broken parts.
U-Bracket Monitor Mounting Instructions
1. Select a level surface for installation.
2. Drill mounting holes using the lower U-bracket as a template and attach the U-bracket with user supplied hardware.
3. Install the monitor on the U-bracket as shown in Figure 2. Adjust the monitor’s position for the best viewing angle before tightening the two screws
on each end.
4. Attach the sun-visor as shown. Attach the antennas so they point upward as shown in Figure 3.

Page 7 of 9
Figure 3
Figure 2
Pedestal Mounting Instructions:
1. Select a level surface for installation.
2. For mounting the pedestal using the adhesive, prep the surface using rubbing alcohol before installation as shown in Figure 4.
3. For mounting the pedestal using screws, drill mounting holes using the pedestal as a template and attach with user supplied hardware.
4. Install the monitor and sun-visor on the pedestal mount as shown in Figure 5. Adjust the monitor’s position for best viewing angel before tightening the set screw
on the pedestal mount. Attach the antennas so they point upward.
Figure 4
Figure 5
Notes:
1. Larger wires and tight connections will provide longer service life for components. For high current wires it is recommended
that terminal blocks or soldered connections be used with shrink tubing to protect the connections. Do not use insulation
displacement connectors (e.g., 3M Scotchlock type connectors)
2. Route wiring using grommets and sealant when passing through compartment walls. Minimize the number of splices to
reduce voltage drop. High ambient temperatures (e.g., under-hood) will signicantly reduce the current carrying capacity of
wires, fuses, and circuit breakers. All wiring should conform to the minimum wire size and other recommendations of the
manufacturer and be protected from moving parts and hot surfaces. Looms, grommets, cable ties, and similar installation
hardware should be used to anchor and protect all wiring.
3. Fuses or circuit breakers should be located as close to the power takeo󰀨 points as possible and properly sized to protect the
wiring and devices.
4. Particular attention should be paid to the location and method of making electrical connections and splices to protect these
points from corrosion and loss of conductivity.
5. Ground termination should be only be made to substantial chassis components, preferably directly to the vehicle battery.
6. Circuit breakers are very sensitive to high temperatures and will “false trip” when mounted in hot enviroments or operated
close to their capacity.

Page 8 of 9
Important! Mount the camera at a location that provides the best view of the area immediately behind the vehicle. Generally, mounting locations toward the
top of the vehicle provide the best eld of view. Lower mounting locations reduce the eld of view and increase the likelihood of damage from road spray.
Carefully remove the unit from its packaging. Examine the unit for transit damage. If damage is found, return the product to your local dealer for war-
ranty replacement. Do not use damaged or broken parts.
U-BRACKET CAMERA MOUNTING INSTRUCTIONS:
1. Select a level surface for installation.
2. Drill mounting holes using the lower U-bracket as a template and attach the U-bracket with user supplied hardware.
3. Install the camera and sun-visor on the U-bracket as shown in Figure 6.
4. Adjust the camera’s position for the best viewing angle before tightening the two screws on each end.
5. Attach the antenna so that it is vertical as shown in Figure 7.
Figure 6
CAMERA MODEL EC2027-WC2
INSTALLATION AND MOUNTING:
For reference only Figure 7
WIRING INSTRUCTIONS:
Important! Waterproof all connections whether inside or outside the vehicle by using sealant and wrapping with insulation tape. Wrap tape tightly,
overlapping by one-half widths so there are no gaps.
The unit is designed for electrical systems from 12 to 24 VDC (10 to 30 VDC extremes).
The wiring for all systems is:
Red Wire Positive (+)
Black Wire Negative (-)
All wiring should be a minimum of 20 AWG. A 3-amp fuse in the positive
line is required (see Figure 8).
3
Figure 8

Page 9 of 9
Unit 1, Green Park, Coal Road
Seacroft, Leeds, England LS14 1FB
[phone]
[email protected]
ECCOESG.co.uk
833 West Diamond St
Boise, Idaho 83705
800-635-5900
ECCOESG.com
An ECCO SAFETY GROUP™ Brand
ECCOSAFETYGROUP.com
439 Boundary Road
Truganina Victoria, Australia
[phone]
[email protected]
ECCOESG.com/au/en
Replacement Parts and Accessories
Description Part Number
CAMERA EC2027-WC2
MONITOR EC7008-WM2
CABLE PCY-7008-WM
LOW PROFILE ANTENNA ECANTE-R
REMOTE STICK ANTENNA ECANTE-8
PEDESTAL MOUNT MB01
SUN-VISOR AS7000SS
Speci¿cations:
Monitor EC7008-WK2 7” LCD Monitor
LCD Size 7”
Resolution 1024 x 3 (RGB) x 600
Contrast 800:1
Brightness 600 cd/m²
Viewing Angle U: 70 / D: 75, R/L: 75
DOT Pitch 0.0642(W) x 0.1790(H)
Aspect Ratio 0.1506(W) x 0.1432(H)
Operating Frequency 2400 - 2483.5 MHz
Receiving Sensitivity -78 dBm
Decompression Form MPEG4
Modulation 2.4G FSK/GFSK/ Line of sight -unobstructed FHSS
Time Delay 170ms
Transmitting Distance 300m
Micro-SD/TF Card Max. 128G
System Format PAL/NTSC
Power Supply DC 10-32V
Power Consumption Max. 10W
Loudspeaker 1.5W/8
Operating Temperature -20°~+70°C, RH90%
Storage Temperature -30°~+80°C, RH90%
Camera EC2027-WC2
Image Device 1/3” CMOS
TV System PAL/NTSC
Array Size 728x488 Pixels
Sensing Area 4.6228mm x 3.6112mm
Scanning System 2:1 Interlace
Sync. System Internal
Resolution 500 TV Lines
Min. Illumination 0.1 Lux (day), 0 Lux (with IR)
Microphone Yes
Video Output 1.0 vp-p, 75 Ohm
AGC Auto
S/N Ratio Better than 48 dB
White Balance Auto
BLC Auto
Current Consumption 0.5A
Operating Frequency 2400-2483.5-MHz
Transmitting Distance 120M (barrier free)
Decompression Form MPEG4
Transmit Output Power 17 dBm
RF Bit Rate 4Mbps
Operating Temperature -20°C~70°C, RH 90% Max.
Storage Temperature -30°C~80°C, RH 90% Max.
Electronics Controls Company “ECCO” (Manufacturer)
ECCO warrants that on the date of purchase, this product will conform to ECCO’s specications for this product (which are available from ECCO upon request). This
Limited Warranty extends for twelve (12) months from the date of purchase.
DAMAGE TO PARTS OR PRODUCTS RESULTING FROM TAMPERING, ACCIDENT, ABUSE, MISUSE, NEGLIGENCE, UNAPPROVED MODIFICATIONS, FIRE OR
OTHER HAZARD; IMPROPER INSTALLATION OR OPERATION; OR NOT BEING MAINTAINED IN ACCORDANCE WITH THE MAINTENANCE PROCEDURES SET
FORTH IN ECCO’S INSTALLATION AND OPERATING INSTRUCTIONS VOIDS THIS LIMITED WARRANTY.
Exclusion of Other Warranties:
ECCO MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED. THE IMPLIED WARRANTIES FOR MERCHANTABILITY, QUALITY OR FITNESS FOR A
PARTICULAR PURPOSE, OR ARISING FROM A COURSE OF DEALING, USAGE OR TRADE PRACTICE ARE HEREBY EXCLUDED AND SHALL NOT APPLY TO
THE PRODUCT AND ARE HEREBY DISCLAIMED, EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW. ORAL STATEMENTS OR REPRESENTATIONS
ABOUT THE PRODUCT DO NOT CONSTITUTE WARRANTIES.
Remedies and Limitation of Liability:
ECCO’S SOLE LIABILITY AND BUYER’S EXCLUSIVE REMEDY IN CONTRACT, TORT (INCLUDING NEGLIGENCE), OR UNDER ANY OTHER THEORY AGAINST
ECCO REGARDING THE PRODUCT AND ITS USE SHALL BE, AT ECCO’S DISCRETION, THE REPLACEMENT OR REPAIR OF THE PRODUCT, OR THE REFUND
OF THE PURCHASE PRICE PAID BY BUYER FOR NON-CONFORMING PRODUCT. IN NO EVENT SHALL ECCO’S LIABILITY ARISING OUT OF THIS LIMITED
WARRANTY OR ANY OTHER CLAIM RELATED TO THE ECCO’S PRODUCTS EXCEED THE AMOUNT PAID FOR THE PRODUCT BY BUYER AT THE TIME OF
THE ORIGINAL PURCHASE. IN NO EVENT SHALL ECCO BE LIABLE FOR LOST PROFITS, THE COST OF SUBSTITUTE EQUIPMENT OR LABOR, PROPERTY
DAMAGE, OR OTHER SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES BASED UPON ANY CLAIM FOR BREACH OF CONTRACT, IMPROPER INSTAL-
LATION, NEGLIGENCE, OR OTHER CLAIM, EVEN IF ECCO OR A REPRESENTATIVE OF ECCO HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
ECCO SHALL HAVE NO FURTHER OBLIGATION OR LIABILITY WITH RESPECT TO THE PRODUCT OR ITS SALE, OPERATION AND USE, AND ECCO NEITHER
ASSUMES NOR AUTHORIZES THE ASSUMPTION OF ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION WITH SUCH PRODUCT.
This Limited Warranty denes specic legal rights. You may have other legal rights which vary from jurisdiction to jurisdiction. Some jurisdictions do not allow the exclusion
or limitation of incidental or consequential damages.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Declaration of conformity:
© 2021 ECCO, Inc. All rights reserved.
920-0550-00 Rev. G

Página 1 de 9
Installation Instructions
Wireless Camera/Monitor System
Instrucciones de instalación
Cámara inalámbrica/Sistema de monitoreo
Instalación, cableado y funcionamiento
MODELO DE SISTEMA DE CÁMARA EC7008-WK2
INSTRUCCIONES DE OPERACIÓN:
MS
Digital Color LED Screen
Power
Menu
Record/Select Volume Decrease/Menu
Navigation
Volume Increase/Menu Navigation
Camera Channel Select
Remote Control Sensor
Loudspeaker
U-Support Bracket Pedestal Mount Slot
Mini SD Card Slot
Potencia
Menú
Grabar/Seleccionar
Sensor de
control remoto
Pantalla LED digital a color
Altavoz
Ranura para
tarjeta SD mini
Abrazadera de
soporte en «U»
Ranura de ensamblaje del pedestal
Seleccionador de canal de la cámara
Aumento de volumen/Navegación
del menú
Reducción de volumen/
Navegación del menú
Sensor de atenuación
Ecante-5
*Trigger wire may or may not be required based on your specic application.
¡ADVERTENCIA!
Si no sigue las instrucciones del fabricante a la hora de instalar o usar el producto, pueden producirse daños materiales, y lesiones
graves o incluso mortales a aquellos que pretende proteger!
No instale ni opere este producto de seguridad, a menos que haya leído y comprendido la información de
seguridad contenida en este manual.
1. Para garantizar su propia seguridad y la de las personas a las que intenta proteger, es esencial una instalación correcta, combinada con
la formación de operador en el uso, cuidado y mantenimiento de los dispositivos de alerta de emergencia.
2. Tenga cuidado cuando manipule conexiones eléctricas con corriente.
3. Este producto debe estar conectado a tierra correctamente. Una conexión a tierra incorrecta o unas conexiones eléctricas
cortocircuitadas pueden provocar arcos de corriente alta, lo que puede ocasionar lesiones personales o daños graves en el vehículo,
incluso un incendio.
4. La colocación e instalación adecuadas son vitales para el buen funcionamiento de este dispositivo de alarma. Instale este producto
de forma que permita un rendimiento óptimo del sistema y los controles estén situados de modo que el operador pueda alcanzarlos
cómodamente y manejar el sistema sin perder en ningún momento el contacto visual con la calzada.
5. No instale este producto ni coloque los cables en la zona de despliegue de un airbag. Si el equipo se monta o coloca en la zona de
despliegue de un airbag, el airbag perderá e¿cacia o el equipo puede salir despedido, lo cual puede causar lesiones graves o incluso
mortales. Consulte el manual del propietario del vehículo para conocer la zona de despliegue de los airbags. El usuario u operador son
responsables de determinar una posición de montaje adecuada que garantice la seguridad de todos los ocupantes del vehículo, y deben
evitar zonas que puedan provocar golpes en la cabeza.
6. Es responsabilidad del operador del vehículo asegurarse de que todas las características de este producto funcionan correctamente
durante su uso. Durante su uso, el operador del vehículo debe asegurarse de que no haya componentes del vehículo (como los maleteros
o puertas del habitáculo abiertos), personas, vehículos u otros obstáculos que bloqueen la señal de alarma.
7. El uso de este o cualquier otro dispositivo de alarma no garantiza que los conductores puedan o quieran observar o reaccionar a la señal
de alarma. Nunca dé por hecho que tiene prioridad de paso. Es responsabilidad enteramente suya asegurarse de que puede continuar
de forma segura antes de entrar en una intersección, conducir en sentido contrario, responder a una gran velocidad o caminar por los
carriles de trá¿co o cerca de ellos.
8. El uso de este equipo está destinado exclusivamente a personal autorizado. El usuario es responsable de conocer y acatar todas las
leyes vigentes relacionadas con dispositivos de señales de advertencia. Por lo tanto, el usuario debe comprobar todas las leyes y
normativas de ámbito metropolitano, regional, nacional y cualquier otro ámbito pertinente. El fabricante no asume responsabilidad alguna
por pérdidas derivadas del uso de este dispositivo de alarma.
¡IMPORTANTE! Lea todas las instrucciones antes de instalar y utilizar. Instalador: Este manual se debe entregar al usuario ¿nal.
¡PRECAUCIÓN!
Al perforar cualquier super¿cie del vehículo, asegúrese de
que no haya cables eléctricos, mangueras de combustible,
tapicería, etc. en el área que pudiesen dañarse.