Echo H2 Pitcher User manual

Echo H2 Pitcher Owner’s Manual

Table of Contents
Benefits
. …………………………………………………………. . .
3
S a f e t y I n s t r u c t i o n s …………………………………………. . . 4
P a r t s ………………………………………………………………. . . 6
C h a r g i n g I n s t r u c t i o n s ………………………………………. 7
D i s p l a y I n f o r m a t i o n …………………………………………. 8
H o w t o U s e ………………………………………………………. 9
How to Clean
…………………………………………………….
10
T r o u b l e s h o o t i n g ………………………………………………. 11
P r o d u c t S p e c i f i c a t i o n s ……………………………………… 13
P r o d u c t W a r r a n t y ……………………………………………. 14
The fastest way to reach customer support is to email them at
[email protected].
2

Benefits of Echo H2 Pitcher
The Echo H2 Pitcher can produce hydrogen enriched water
in 10 and 20 minute cycles.
Specialized casing keeps hydrogenated water pure and fresh
a fte r filt e rin g.
Built in rechargeable battery allows the Echo H2 water
Pitcher to be used anytime and anywhere.
Eco -friendly made of tritan plastic which is bpa free.
3

DO NOT
●Put pitcher in the microwave.
●Put pitcher in a dishwasher.
●Freeze.
●Disassemble, repair, or modify the pitcher.
●Soak your product in water. (Cover can be washed.)
●Use product if an abnormality occurs.
○See pages 11 & 12 for troubleshooting options
●Touch the power plug with wet hands; this can cause
electric shock, fire, and product failure.
●Allow children to operate or handle the pitcher
●Use carbonated beverages, green tea, or alcohol in the
pitcher
●Use water above 140 °F/60 °C
●Move the pitcher during hydrogen generation.
●Clean the interior of the pitcher with chemical detergent.
The electrode will be damaged.
●Use excessive force
○if product falls, is thrown, or is dropped call Customer
Care (see page 2)
4
!Safety Instructions
Please be sure to follow these instructions to prevent electric shock, fire, or
explosion which could result in personalinjury or product damage

●Use only DC 5V. Do not charge with a voltage higher
than DC 5V - 2A.
●Keep oxygen outlet on the underside of the pitcher
unobstructed.
●Only use manufacturer certified replacement parts and
charging cables.
●Using the pitcher without water may cause electrode
damage.
●If non -water drinks are used, wash the pitcher with citric
acid within 1 hour.
●Only use water when cleaning the exterior of the pitcher.
Other detergents/chemicals may cause the pitcher to be
discolored or lose paint.
●If the electrodes are completely dry or the product has
not been used for one week or longer. Fill the pitcher
with water and use after 20 minutes.
●Only use filtered water (R.O. or distilled water) in
hydration process.
If the electrodes have calcium build up or are damaged,
performance can be degraded. Do not clean the interior
of the pitcher with chemical detergent.
5
Safety Instructions
Please be sure to follow these instructions to prevent electric shock, fire, or
explosion which could result in personalinjury or product damage
!

Handle
Wa te r
Container
Controller
Dis p la y
Ma in
Body
Co ve r
Battery
Co ve r Oxyge n
Ou t le t
Bottom
Vie w
Sid e
Vie w
Parts
6

Using a Portable Charger:
Charge portable charger
before use.
Connect the C type USB
cable to the portable
charger and to the USB
port of the pitcher.
●Product can be used while charging.
●If the battery display LED is Red, the pitcher is charging. if
the LED Display is Green, the pitcher is fully charged.
●Use a charging adapter with 5V, 2A or higher.
●Hydrogen generation is more effective when pitcher is
plugged in and/or fully charged
Charging
For Outlet Charging:
Connect the C type USB
cable to the outlet
adapter and to the USB
port of the pitcher.
7

▣Operating State
Display
- Blue: 10 minute mode
- Green 20 minute mode
- Red: Electrode Cleaning
mode
Three flashes indicate end
of filtration cycle
▣Electrode
Washing Display
▣Time and Error
Display
- 10 minute or 20 minute
mode
- Remaining time in
filtration cycle
ERROR Display.
EL : Low Current
: No water
▣Hydrogen Water
Generation
Selection display
LED.
▣Cleaning Mode
Button
Error
DIsplay. EL
•Operation in low current
or electrode dry
condition.
•Water container is
empty
•Activate with warm water
(140°F/60°C or less) and use
•Fill the water container with water
and use.
Display Information
▣Hydrogen
Water Button
- Start/stop button -
10 minute/ 20
minute cycle
duration select
- Mute/Unmute
function
▣End of Operation
mute/unmute
indicator
- Press hydrogen water
button 3 times to
mute/unmute end of
operation chime.
▣Low Battery
Indicator
- If LED flickers or blinks
battery needs to be
charged.
▣Battery Life Indicator
- Red: Needs to be
charged, or is charging
- Green: Product is fully
charged
8

9
Hydrogen Water Button
Before first use, open the top cover and unscrew and remove the electrode
moisture retention caps (2 pieces) inside the water pitcher.The moisture
retention caps prevent electrodes from drying out during distribution.
○If the pitcher willnot be used for more than a week, fill the electrodes with
water and lock the moisture retention cap by screwing them in place. It is
important to remove caps before next use.
For first use or if you have not used the pitcher for more than one week, follow
cleaning procedures. (see page 10)
Op e n th e t o p cove r a nd fill with filt e re d wa t e r (R.O. o r d is tille d ).
10 minute Cycle:
Press and hold the Hydrogen Water Button for 2 seconds and the BLUELED will
light up at the bottom. Display will show 10 minutes. After 10 minutes, the Echo H2
Pit ch e r will t u rn o ff a u t o m a t ica lly
20 Minute Cycle:
For higher concentrations of hydrogen, press the operating button twice and the
GREEN LED will light on the bottom. After 20 minutes, the Echo H2 Pitcher will turn
o ff a u t o m a t ica lly.
How to Use
Electrode
Mo is t u r e
Retention Caps
(Remove by
unscrewing
before use)
If you want to
stop generating
hydrogen, press
and hold the
Hydrogen Water
Button for 2
seconds,
hydrogen
ge n e r a t io n will
stop and pitcher
will t u r n o ff.

How to Clean
Cleaning Button
Add baking soda to
water
②
Pour
dissolved
baking
soda and
water into
Pitcher
10
Cleaning Procedure
●When using for the first time, put approx. ¼ cup (50cc) of water
(68°F~104°F/ 2 0 ℃~ 40℃) in a cup, dissolve 2 tsp/10g of baking soda into the
wa te r .
●Once fully dissolved, pour water/baking soda solution into water container and
leave for about 1 hour. (leaving it for 1-2 hours will have a better cleaning effect.)
●Aft e r 1 hour r in s e wit h cle a n wa te r (d is tille d w a te r o r RO w a te r ) 2 ~ 3 t im e s
before use.
●Fill th e cle a n wa te r in t h e p itch e r/ke t tle (d is tille d w ate r or RO w ate r a ro u n d
(68°F~104°F/ 2 0 ℃~ 40℃) about 2/3 fulland run the cleaning mode 2 ~ 3 times.
For best results change the water each time (RED LED turns on when cleaning
m o d e is a ct iva te d )
●Clean the inside with a soft cloth, cotton swab, or sponge. If dust or dirt is not
removed,add some water and gently swirl severaltimes.
Extra Cleaning Tips
○For better cleaning, use with the power cable connected.
○Water that is rich in minerals may have cloudy bubbles and less hydrogen
bubbles. If there are less hydrogen bubbles, use the above cleaning mode
before use.
○Water Container Cleaning - Clean the pitcher/kettle with a soft cloth or
sponge, etc., and thoroughly rinse it before use.
○Product Appearance - Wipe off dust and dirt from the pitcher/kettle with
a wet cloth. (Keep water away from power terminal and battery)
Long-term use of the pitcher/kettle may cause the electrode to smell. The smell of
the electrode has nothing to do with hydrogen production and does not affect the
taste of water. Periodically, clean the electrode and pitcher/kettle to prevent odors.
Smell may require several cycles of cleaning to remove.