Teknik 5401562 User manual

Sit and surf.
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Computer Workcentre
5401562
Teknik
www.teknikoffice.co.uk

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
2-3
3-4
5-16
21-24
25-28
29-30
31
Part Identification
A RIGHT END (1)
B LEFT END (1)
C UPRIGHT (1)
D TOP (1)
D28 RIGHT DRAWER SIDE (2)
D29 LEFT DRAWER SIDE (2)
D78 DRAWER BACK (2)
D707 DRAWER BOTTOM (2)
E MODESTY PANEL (1)
F BACK (1)
G BRACE (1)
H KEYBORAD SHELF (1)
I KEYBOARD FRONT (1)
J KEYBOARD BACK (1)
K KEYBOARD SIDE (2)
L DRAWER FRONT (2)
Q END MOLDING (1)
R BASE (1)
Page 2

åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
Part Identification
A
B
C
D
E
F
G
H
I
J
K
KL
L
R
D28
D28
D29
D29
D78
D78
D707
D707
Hardware Identification
35GA CABINET RIGHT - 2 35GB CABINET LEFT - 2 35GC DRAWER RIGHT - 2 35GD DRAWER LEFT - 2
35AW CABINET RIGHT - 1 35AY DRAWER RIGHT - 1 35AZ DRAWER LEFT - 1
35AX CABINET LEFT - 1
Q
Page 3

åScrews are shown actual size. You may receive extra hardware with your unit.
Hardware Identification
FILE GLIDE - 4
15B
BLACK 9/16" PAN HEAD SCREW - 1
UU
BLACK 9/16" LARGE HEAD SCREW - 18
TT
ANGLE BRACKET - 7
DD
BLACK 1-1/4" FLAT HEAD SCREW - 6
PP
SS SILVER 5/8" MACHINE SCREW - 6
BROWN 7/16" LARGE HEAD SCREW - 8
VV
BLACK 1-7/8" FLAT HEAD SCREW - 2
OO
RR BROWN 1" FLAT HEAD SCREW - 4
HINGE - 2
GG
EXTENSION
BRACKET - 2
EE
BLACK 1-1/16" MACHINE SCREW - 1
QQ
WW GOLD 5/16" FLAT HEAD SCREW - 20
CATCH - 1
HH LATCH - 1 II
METAL PIN - 3
NN
BARREL NUT - 1
JJ
MM SLIDE CAM - 4
PULL MOUNT - 6
KK
PULL - 3
LL
NAIL - 15
XX
30S BLACK 1-9/16" FLAT HEAD SCREW - 8
HIDDEN CAM - 10
BB2 CAM DOWEL - 10 CC2
Page 4

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push ten HIDDEN CAMS (BB2) into the ENDS (A and B),
UPRIGHT (C), MODESTY PANEL (E), and BRACE (G). Then
insert a CAM DOWEL (CC2) into each HIDDEN CAM.
(10 used)
(10 used)
Arrow
Do not tighten the HIDDEN CAMS in this step.
Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
Arrow
A
B
C
EG
CC2
BB2
Page 5

Step 2
å Fasten the CABINET RIGHTS (35GA) to the RIGHT END (A)
and a CABINET LEFTS (35GB) to the UPRIGHT (C). Use four
GOLD 5/16" FLAT HEAD SCREWS (WW) through holes #1
and #3.
å Fasten the CABINET RIGHT (35AW) to the opposite
surface of the UPRIGHT (C).
å NOTE: Be sure the roller end of each RAIL is at the same end.
1
1
1
1
2
2
2
2
3
3
3
3
Roller end
Roller end
GOLD 5/16" FLAT HEAD SCREW
(10 used in this step)
WW
These holes must be here.
These holes must be here.
Surface with
HIDDEN CAMS Surface with
HIDDEN CAMS
A
C
Remember:
Righty tighty.
Lefty loosey.
Page 6

Step 3
å Fasten seven ANGLE BRACKETS (DD) to the ENDS (A
and B) and UPRIGHT (C). Use seven BLACK 9/16" LARGE
HEAD SCREWS (TT).
å NOTE: Be sure the edges of the ANGLE BRACKETS are
even with the edges of the ENDS and UPRIGHT.
å Fasten the END MOLDING (Q) to the LEFT END (B). Use
three BLACK 9/16" LARGE HEAD SCREWS (TT).
å NOTE: There are no pre-drilled holes in the END
MOLDING (Q). Turn the screws into the groove of the END
MOLDING. Do not over tighten.
BLACK 9/16" LARGE HEAD SCREW
(10 used in this step)
TT
(7 used)
DD
DD
A
C
B
Q
Groove
Page 7
Surface with
HIDDEN CAMS Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS

Step 4
å Insert a METAL PIN (NN) into the hole in the TOP (D).
Fasten the END (B) to the TOP. Tighten two HIDDEN CAMS.
å NOTE: Be sure the PIN in the TOP inserts into the edge of
the END.
å Fasten the MODESTY PANEL (E) to the END (B). Tighten
two HIDDEN CAMS.
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
B
D
E
Notch
Surface with HIDDEN CAMS
Surface with
HIDDEN CAMS
NN
Page 8

å Fasten the UPRIGHT (C) to the MODESTY PANEL (E). Use
two BLACK 1-7/8" FLAT HEAD SCREWS (OO).
å Insert two METAL PINS into the short edges of
the BRACE (G).
å Fasten the BRACE (G) to the UPRIGHT (C). Tighten one
HIDDEN CAM.
å NOTE: Be sure the METAL PIN in the BRACE inserts into
the hole in the UPRIGHT. You may need to hold the BRACE
up until the RIGHT END is fastened in the next step.
Step 5
E
Surface with
HIDDEN CAMS
Surface with
HIDDEN CAMS
C
BLACK 1-7/8" FLAT HEAD SCREW
(2 used in this step)
OO
Arrow
Minimum
190 degrees
Maximum
210 degrees
G
Page 9
D

å Fasten the RIGHT END (A) to the TOP (D). Fasten two
HIDDEN CAMS.
å Fasten the RIGHT END (A) to the BRACE (G). Tighten the
HIDDEN CAM.
å NOTE: Be sure the PIN in the BRACE inserts into the hole
in the END.
å Fasten the BASE (R) to the RIGHT END (A) and UPRIGHT (C).
Use four BLACK 9/16" LARGE HEAD SCREWS (TT).
Step 6
Arrow
Minimum
190 degrees
Maximum
210 degrees
A
G
R
C
Curved edge
BLACK 9/16" LARGE HEAD SCREW
(4 used in this step)
TT
Page 10
D