Eden 10 Series User manual

1

2
What you need to know: Front
•Ridge
•Slopes
•Top section
•Outer post
•Front brace
•Verticals
•Base
•Triangle
•Head section
•Door track
•Gusset
•Door posts
•Door brace
•Front sill +
threshold

3
What you need to know: Rear
•Ridge
•Slopes
•Rear end brace
•Outer mitre
•Rear brace
•Base
•Triangle
•Centre vertical bar
•Mitre
•Gusset
•Vertical
•Rear/side sill

4
What you need to know: Middle
Gutter
Side glazing bars
Base
Side brace
Side brace

5
Instructions overview:
1. Assemble 2 sides, back, front.
2. Put those four sides together. Keep braces and gussets
finger-tight only at this point.
3. Attach the roof and ridge.
4. Attach the roof ventilator
5. Move the whole structure into final position
6. Assemble the door
7. Glaze door while unattached to main structure.
8. Attach the glazed door.
9. If you have a shade kit, attach the aluminium brackets
(but obviously not the shade cloth yet).
10. Identify the position for the anchor legs and, if necessary,
dig holes for them.
11. Attach anchor legs.
12. Ensure the glasshouse is square and level.
13. Glaze all the lower level glass panels.
14. Attach the louvre on the back at this point (now it has
something to sit on) using preloaded bolts.
15. Glaze the louvre.
16. Glaze all the middle level glass panels.
17. Glaze all the roof panels.
18. Glaze front and rear small upper panels.
19. Tighten all bolts up.
20. Re-square and level and, if necessary, concrete in

6
All 10 series have the same assembly procedures, variations are in
the length of Ridge, gutter and sills also the number of roof and
side bars.
When the Glasshouse exceeds 4m or 12’ in length we make this as
an extension, the join may vary as to where this goes, normally as
near to the middle as possible e.g., 1016 (5.1m) two units at 2.55m.
Note:
All bolts are standard
10mm size.
Do not fully tighten all
bolts until the glasshouse
has been glazed. This is to
allow for movement of the
frame if the base is not
completely level or square.

7
Page:
2 & 3 Front & Rear views
4 & 5 Side Wall Assembly
6 & 7 Rear Wall
8 & 9 Front Wall
10 & 11 Joining sections together
12 & 13 Attaching Ridge and Roof bars
14 & 15 Ventilator, assemble & attach
16 & 17 Louvre, assemble & attach
18 –21 Doors, assemble, fit and glaze.
22 Anchoring Glasshouse
23 Glazing Instructions
24 Glazing layout
25 Attaching End Caps
26 & 27 Extensions, Assemble and joining
28 Dimensions

8
You are now embarking on your journey to build your Eden
glasshouse! If the ride gets rough, don’t hesitate to contact us at
[email protected]. You will build the sides, back and front
separately and then join them together afterwards. Please start by
opening the box/s marked ‘middle’.
Good luck!

9
For Ease of assembly, lay-out with the bolt hole / tracks, top side up, like the Internal view.
Preload Nuts and Bolts where marked X
X
X
X
X
X
X
X
X

10
Parts needed:
•Gutters
•Side glazing bars (1795mm)
•Side braces (2128mm)
•Side sills
•Base
•Nuts and bolts

11
View (c) shows
the end of the
base & sill with
the slot, for
attaching the
front & rear.
Note –Base
option now
comes with sill
attached

12
REAR WALL ASSEMBLY
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Preload a Nuts & Bolts as shown marked Xfor use later to join
units together, attach louvres and corner stiffening
X
X
X
X
X
X
Note:
All bolts are standard
10mm size.
Do not fully tighten all
bolts until the glasshouse
has been glazed. This is to
allow for movement of the
frame if the base is not
completely level or square.

13
View from outside
of glasshouse

14
•Outer mitres (2103mm)
•Centre vertical bar
(2812mm)
•8’ gusset
•Nuts and bolts
You will notice that the gussets, slopes, and verticals all have
either blue, red, green, or yellow dots on them. These dots
show what side of the glasshouse the verticals and slopes are
on.
These fit together as shown on the picture on the page above
Looking at the glasshouse from the outside:
BLUE: Left side, front wall
RED: Right side, front wall
GREEN: Left side, rear wall
YELLOW: Right side, rear wall
Parts needed:
•Verticals (1795mm)
•Slopes (1795mm)
•Rear brace (1855mm)
•Side sills (2975mm)
•Base (2975mm)
•8’ triangle
•LH+RH mitre (2400mm)
•Rear end brace (2935mm)

15
Corner Bars:
Note the bolt track
goes inside, the flat
edge goes from the
gusset to the
sill/base. The lug
(with the hole top
and bottom) faces
externally.
Those holes are for
joining extensions.
Insert the extra
bolts to attach the
Louvres and centre
bolts on the braces,
as well as top and
bottom of corner
bars, this will assist
when bringing the
sections together

16
The corner bar, glazing
lug with a hole top and
bottom goes to the
outside, this is only for
joining extensions
Corner Braces: Insert an extra bolt in both Door
Posts to be used later to install the Corner Braces
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Door brace goes
beneath door track on
inside of front wall
Preload Nuts and Bolts where marked X
External view
Internal view

17
•Top sections (405mm)
•8’ gussets
•Front/door sill (2975mm)
•Base (fitted on door sill)
•Threshold
•Nuts and bolts
•Support bracket for door track
•Head section (814mm)
Parts needed:
•Verticals (1795mm)
•Slopes (1795mm)
•Door track
•8’ triangle
•Door posts (2094mm)
•Front brace (1855mm)
•Door brace (453mm)
•Outer posts (1993mm)
To make it easier for you, we have put red or blue dots
on the verticals and slopes in the front box. When
assembling these, makes sure the dots match up (see
page 12).

18
The door track is preassembled in the
factory, just attach
J1, rear cross brace from inside, J2 is the
door track from outside.
View of low entrance door,
there is rebate in top sill for
door post to go to the
bottom door track.
Normal door with high sill and track.
The door post goes as far as the sill sitting on the
base, brace is attached to the door post. Three
screws are provided to attach the Threshold to
the door track and base.

19
This view is from inside looking at the ridge
bar joining at the extension end, see how the
ridge now sits on top of the corner section.
View looking down on the ridge bar attaching the extension
If adding to an existing glasshouse,
remove the centre sill & base once the
extension is attached
EXTENSIONS

20
The holes for the Extension bracing are NOT Predrilled, get
the braces in place, clamp and drill
IF on an Eden Base, attach the brace to the anchor leg (This leg
has an extra bracket attached).
If NOT on the Eden Base move the brace up slightly and attach
to the corner section, Double bolt.