Eden 6 Series User manual

6 SERIES SINGLE DOOR
GLASSHOUSE ASSEMBLY INSTRUCTIONS
Phone: [phone]

GLASSHOUSE LAYOUT DIAGRAM
Throughout this instruction booklet and in the
boxes of parts you have received you will find
these colours used to show which end
and side your parts are.

FRONT WALL LAYOUT

REAR WALL LAYOUT

SIDE WALL LAYOUT
Please note that the Side Walls shown have the Eden Base Kit attached.

ANCHORING THE GLASSHOUSE
The anchors should be on all four corners of the glasshouse.
Longer models will have extra anchors which can be spaced
out along the side.
Please note that the holes in the base for
the anchor posts are not factory drilled- you will need to drill
your own where best fits.
To attach the anchor posts, you will need to drill 4 holes to
match the holes in the anchor posts supplied. Then bolt to sills.
Check the glasshouse is square and level (square means that
the diagonal measurements are equal from base to corner)
Pour concrete into holes to stabilise.
Normally ½ bag of ready-mix concrete is sufficient per leg,
ensure there is concrete under and above the foot.
When set hard, backfill hole.
.

YOUR EDEN GLASSHOUSE COMES WITH SILL + BASE PRE-ASSEMBLED.
If you have ordered ‘No Base Kit’ you will receive only the Sills with no Base panels.
GUSSETS
Gussets are placed on the inside of the Glasshouse,
with the stickers facing outward. The coloured sticker dots
should be covered by the Vertical of the same colour when
looking from the outside of the Glasshouse.
HIGH WIND ZONE AREAS
If your glasshouse is to be erected in a high wind zone area,
please construct a wind shelter or wind break to ensure
your glasshouse lasts to its full potential.

ASSEMBLY INSTRUCTIONS OVERVIEW
Please read instructions fully before assembling.
-Identify the position for the anchor posts and dig holes where necessary.
-Assemble Side Walls.
-Assemble Rear Wall.
-Assemble Front Wall.
-Attach all Walls. NOTE - Keep braces and gussets finger-tight only at this point.
-Attach Roof Bars, Roof Braces, and Ridge Bar.
-Attach Roof Vent(s).
-Move structure into final position.
-Assemble Door.
-Glaze door while unattached to main structure.
-Attach the glazed door.
-Attach the louvre to the Rear Wall using pre-loaded bolts, and glaze.
-If you have a shade kit, attach the aluminium brackets – but not the shade cloth yet.
-Attach anchor posts.
-Ensure glasshouse is squared and level.
-Begin glazing glasshouse, starting with all lower-level glass panels.
-Glaze all middle level glass panels.
-Glaze all roof panels.
-Glaze front and rear small upper panels.
-Tighten all bolts.
-Re-square and level the glasshouse, concrete in.

6 SERIES GLASSHOUSE NOTES
PLEASE OPEN ONLY ONE BOX AT A TIME AND COMPLETE SECTION ASSEMBLY BEFORE
OPENING THE NEXT BOX.
All bolts are 10mm standard size.
Do not fully tighten all bolts until the glasshouse has been glazed. This allows for movement in
the frame if the base is not completely level or square.
For ease of assembly, lay the parts for each section out on the ground or a table with the bolt holes and
bolt tracks facing upward.

PRELOADING
The below diagram illustrates how bolts are pre-loaded.
-Bolts slide down the bottom tracks of Side + Roof Bars, Mitres, Posts and Head Sections.
-Bolts will need to be pre-loaded in the Front Wall, Rear Wall, and Mid Wall sections.
-In some cases, several bolts will need to be pre-loaded onto one part.
For ease of assembly, please refer to the Pre-load Diagram in each section after unpacking.

SIDE WALL ASSEMBLY:
Gutter + Sill length, and number of Side Bars depends on model size.
NOTE: Side and Roof Bars come with glazing rubber pre-installed to 50mm from the top end
(which attaches to the Gutters). This has been done to make glazing the glasshouse easier, as
you will need to slide the top pane of glass slightly underneath the Gutter, the gap in the
rubber stops unnecessary pressure being applied.
Roof Bars (1197mm), Roof Braces (1597mm), and Vent Pack in this box will be used later!
Parts Needed:
-Gutters
-Side Sills (with Base attached if selected)
-Side Bars (1.490mm)
-Side Braces (1597mm)

PRE-LOAD DIAGRAM: SIDE WALLS
Pre-load one bolt at either end of each Side Bar, to attach to the Gutter and Side Sill.

SIDE WALL ASSEMBLY NOTE: Keep bolts finger tight at this point.
Lay Side Bars, Gutters, Side Braces, and Side Sills according to the diagram below (with bolts pre-loaded).
First, attach Side Bars to Gutters and Sills, and then attach Side Braces to Sills and Gutters.

All Gussets, Slopes, and Verticals have
either a Blue, Red, Green, or Yellow dot
on them.
These dots indicate what end and side of
the glasshouse the parts are intended
for.
Blue – Left Side of the Front Wall
Red – Right Side of the Front Wall
Green – Left Side of the Rear Wall
Yellow – Right Side of the Rear Wall
NOTE:
Louvre Pack will be installed later!
REAR WALL Tip
Parts Needed:
-LH Slope GREEN(1197mm)
-LH Vertical GREEN (1490mm)
-RH Slope YELLOW (1197mm)
-RH Vertical YELLOW (1490mm)
-Rear Brace (1563mm) x2
-Rear Sill with Base Kit (unless specified)
-6 Series Top Triangle Gusset (in glass crate)
-LH + RH Mitres (1990mm)
-Rear Crossmember (648mm)
-Rear Gussets (Yellow + Green)

PRE-LOAD DIAGRAM: REAR WALL
Pre-load 3 Bolts into the Rear Crossmember.
-3 for the Top Triangle
Pre-load 2 Bolts into each of the LH and RH Mitres.
-1 for the Top Triangle
-1 for the Rear Sill

REAR WALL ASSEMBLY
Lay out all parts from the “Rear Wall” box according to the below diagram.
-Attach LH and RH Verticals to Side Gussets
-Attach LH and RH Slopes to Side Gussets
-Fix Rear Crossmember to Top Triangle
-Bolt Top Triangle to LH and RH Slopes
-Attach Rear Base to LH and RH Verticals
-Fix Mitres to Top Triangle and Rear Sill
-Flip the frame over
-Attach Rear Brace (top end) to Gussets
-Attach Rear Braces (low end) to
the back of the LH and RH Mitres

All Gussets, Slopes, and Verticals have
either a Blue, Red, Green, or Yellow dot
on them.
These dots indicate what end and side
of the glasshouse the parts are
intended for.
Blue – Left Side of the Front Wall
Red – Right Side of the Front Wall
Green – Left Side of the Rear Wall
Yellow – Right Side of the Rear Wall
FRONT WALL Tip
Parts Needed:
-LH Slope BLUE (1197mm)
-LH Vertical BLUE (1490mm)
-RH Slope RED (1197mm)
-RH Vertical RED (1490mm)
-Front Brace (1563mm) x2
-Track Support (478mm)
-Door Brace (605mm) x2
-Front Sill (1835mm)
-6 Series Triangle Gusset (in glass crate)
-Front Gussets (Red + Blue)
-Head Section (438mm)
-LH + RH Door Posts (1990mm)
-Door Crossmember
-Track Support Brackets (in the parts bag!)
NOTE: Door Parts to be used shortly!

PRE-LOAD DIAGRAM: FRONT WALL
Pre-load 3 bolts into the Door Crossmember.
-3 for the Top Triangle
Pre-load 3 bolts into each of the LH and RH Door Posts
-2 at the top end for the Top Triangle
and Door Braces
-1 at the bottom end for the Front Door Sill

FRONT WALL ASSEMBLY
LAY OUT ALL PARTS ACCORDING TO THE DIAGRAM BELOW.
NOTE: Track Supports sit in front of the Support Brackets
and behind the Top Track. The flat face with NO bolt
holes on will sit facing forward.

FRONT WALL ASSEMBLY
-Attach LH and RH Verticals to Gussets
-Attach LH and RH Slopes to Gussets
-Bolt Door Crossmember to Top Triangle
-Attach Top Triangle to LH and RH Slopes
-Attach Front Door Sill to LH and RH Verticals
-Attach Top Track to LH and RH Slopes
-Bolt Track Support Brackets
to LH and RH Slopes
-Fix Track Supports to Top Track,
as well as LH and RH Slopes
-Attach Door Posts to Front Door Sill,
and Top Triangle
-Flip the frame over
-Attach Door Braces and Front Braces