Eden The Vienna Trellis User manual

Check Box for These Contents
In the event of missing or defective parts please call our customer service
dept. at 1 800 282 9346, ext #20 (Mon. to Fri.8:00 AM to 4:00 PM EST).
1. Keystone Lid (1)
2. Keystone Insert (1)
3. Keystone Body (1)
4. Keystone Bottom Plate (1)
5. Arch Spindle - Long (2)
6. Arch Spindle - Short (2)
7. Arches (2)
8. Post Caps (2)
9. Top Rail (1)
10. Posts (2)
11. Vertical Spindles (7)
12. Horizontal Spindles (3)
13. Bottom Rail (1)
14. Ground Stakes (2)
15. 1 1/2”Self-Auguring Stainless Steel Screw (20)
Tools You Will Need
• Cordless Drill
• Hammer
• Tape Measure
• Level
• Shovel
General Information
• Read Instructions through carefully before beginning assembly.
• When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching.
• We recommend an area approx 5’x 8’for unobstructed assembling.
• You should not need to use excessive force when assembling component.
The Vienna Trellis
Please read through before starting assembly.
ASSEMBLY INSTRU C T I O N S
1
www.edenarbors.com
1
2
15
Not to Scale
6
3
4
5
IMPORTANT: CHECK THE INSIDE OF YOUR POSTS FOR ALL MATERIALS.
Ver 1/Aug 2011
14
83.75 in
49 in
42 in
6 in
49 in
2 in
7
8
9
10
11
12
13

2
www.edenarbors.com
1
Lay out the top rail, bottom rail, horizontal spindles, and
vertical spindles as shown. Start by inserting the 7 vertical
spindles into the 3 horizontal rails.
Note that the routed holes on the horizontal rails are slightly
offset from the centre. Ensure that the holes are aligned as per
the inset image.
Continue to insert the assembly into the top and bottom
rails.
Note the difference between the two rails. The bottom rail
only has one routed side whereas the top rail has additional
holes for the arch spindles.
Align and insert the rails into one of the post.
Note that the pre-drilled holes are located on the back side
of the trellis.
Proceed with the other post.
Flip the trellis over and using the provided screws, fasten
the posts to the top and bottom rails in place as shown.
1
2
3
4
STE P O NE
2
3
NOTE: Assembly will be easier if performed by two people
Note orientation
5
5

3
1915 Dove St., Port Huron MI USA 48060
Toll Free Phone: [phone] Toll Free Fax: [phone]
www.edenarbors.com
STE P T WO
Assemble the keystone by inserting the keystone insert into the keystone
body as shown below,followed by the two arches.
Note that the arches will be marked with a sticker where they meet the
keystone.
Using two of the provided screws,fasten the arches into the keystone
insert as shown.
Drive two more screws to the underside of the keystone.
Snap the top and bottom lid to complete the arch assembly.
Arch Assembly
1
Insert first
2
3
4
1
2
3
4
Sticker
Sticker

4
1915 Dove St., Port Huron MI USA 48060
Toll Free Phone: [phone] Toll Free Fax: [phone]
www.edenarbors.com
STE P T HR E E
Place the post cap onto each of the post.Note that there are left and
right post caps.Please see image aside for orientation.
Insert the arch spindles into the top rail as shown.The short spindles
would be on the outer side of the rail,and the long spindles would
be on the inner side of the rail.
Starting on one end, guide the arch assembly and arch spindles
into the pre-routed holes as shown.
Fasten the arch assembly to the posts using four screws (2 per post)
provided.
Arch Assembly
1
2
3
4
1
Long
2
Long
Short
Short
3
4

5
STE P F OU R
Insert the ground anchoring stakes into the bottom of the trellis
posts. Secure with screws as shown aside.
Mounting Into the Ground
Install the Ground Anchor Stakes
1915 Dove St., Port Huron MI USA 48060
Toll Free Phone: [phone] Toll Free Fax: [phone]
www.edenarbors.com
4
Trellises must be well secured in the event of high winds, etc. We
have provided two ground anchoring stakes for securing the trellis
either into the ground or into a concrete footing. If you are
installing your trellis directly to the wall of your home,or on a wood deck
or concrete surface,please see your hardware store for the appropriate
galvanized bracket hardware.
STE P F IV E
Move the trellis to its final location. When you are satisfied with
the location, mark the positions of the posts, then move the trellis
aside and lay it carefully on it’s side. Excavate the 2 post holes
approximately 12" deep x 6" diameter. Carefully move the trellis
back into position.
Level it both vertically and horizontally into the excavated holes.
Backfill the holes with the excavated soil.
Note: For a stronger installation, purchase two 2x4 pressure
treated lumbers and sleeve them into the posts.Wood posts
should be inserted 4”into the trellis posts and ±24”into the
ground.
A
B
C
Install Trellis into Ground
A
5
12”
Level
6“
B
C