Edge-Core WA4101-Cradle User manual

www.edge-core.com
User Guide
Powered by Accton
WA4101-Cradle
IEEE 802.11b/g
Cradle Access Point

User Guide
Guide
WA4101-Cradle
IEEE 802.11b/g Cradle Access Point,
with Cradle Charger for Wi-Fi Phone

WA4101-Cradle
E102006-EK-R01
149100036300E

i
Compliances
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected
• Consult the dealer or an experienced radio/TV technician for help
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance
of 20 centimeters (8 inches) between the radiator and your body. This transmitter must
not be co-located or operating in conjunction with any other antenna or transmitter.
The antenna(s) used for this transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to
channels 1 through 11.
Japan VCCI Class B

ii
EC Conformance Declaration
Marking by the above symbol indicates compliance with the Essential Requirements of
the R&TTE Directive of the European Union (1999/5/EC). This equipment meets the
following conformance standards:
• EN 60950-1 (IEC 60950-1) - Product Safety
• EN 300 328 - Technical requirements for 2.4 GHz radio equipment
• EN 301 489-1, EN 301 489-17 - EMC requirements for radio equipment
• EN 50385 - The Compliance of Radio Base Stations and Fixed Terminal Stations for
Wireless Telecommunication Systems with the Basic Restrictions or the Reference
Levels Related to Human Exposure to Radio Frequency Electromagnetic Fields (110
MHz - 40 GHz)
This device is intended for use in the following European Community countries:
Requirements for indoor vs. outdoor operation, license requirements and allowed
channels of operation apply in some countries as described below:
• In Italy the end-user must apply for a license from the national spectrum authority to
operate this device outdoors.
• In Belgium outdoor operation is only permitted using the 2.46 - 2.4835 GHz band:
Channel 13.
• In France outdoor operation is only permitted using the 2.4 - 2.454 GHz band: Channels
1 - 7.
• Austria • Belgium • Denmark
• Finland • France • Germany
• Italy • Luxembourg • Netherlands
• Norway • Spain • Sweden
• Switzerland • United Kingdom • Portugal
• Greece • Ireland • Iceland

iii
Table of Contents
Chapter 1: Introduction 1-1
Package Checklist 1-1
Hardware Description 1-2
Wi-Fi Phone Cradle 1-3
LED Indicators 1-3
Ethernet Port 1-3
Power Socket 1-4
Reset Button 1-4
Chapter 2: Hardware Installation 2-1
Chapter 3: Initial Configuration 3-1
Connecting to the Web Interface 3-1
Management Access Through a Wireless Connection 3-2
Changing a PC’s IP Address 3-2
Logging into the Web Interface 3-4
Using the Setup Wizard 3-6
Chapter 4: System Configuration 4-1
Information 4-3
System 4-3
Client 4-4
Network 4-5
Event Log 4-6
System Settings 4-7
Administration 4-7
Reboot System 4-8
Wireless VAP Settings 4-9
Basic 4-9
Channel Setting 4-10
WEP Security 4-11
WPA-PSK Security 4-12
Network Settings 4-14
DHCP Client 4-14
DHCP Server/NAT 4-15
PPPoE 4-16
Time and Log 4-17

iv
Contents
Updating Firmware 4-18
Upgrade via the Web Page 4-18
Upgrade via a Remote Server 4-19
Appendix A: Troubleshooting A-1
Diagnosing Access Point Indicators A-1
Wireless Connection Problems A-1
Appendix B: Cables and Pinouts B-1
Twisted-Pair Cable Assignments B-1
10/100BASE-TX Pin Assignments B-1
Straight-Through Wiring B-2
Crossover Wiring B-2
Appendix C: Specifications C-1
Glossary
Index

1-1
Chapter 1: Introduction
The WA4101-Cradle is an IEEE 802.11b/g (Wi-Fi) access point that provides a
quality wireless Voice over Internet Protocol (VoIP) service for Wi-Fi phones, and
high-speed data communications between internet and other 802.11b/g mobile
devices. The WA4101-Cradle also includes a cradle for charging an Edge-Core
Wi-Fi phone.
The access point software provides two “virtual” wireless interfaces that can be used
to separate different types of network traffic. Both wireless interfaces provide
gateway functions, such as a DHCP server and Network Address Translation (NAT),
that route data from wireless clients to the wired network. In addition, the access
point offers full network management capabilities through an easy-to-use web
interface.
In addition, the access point offers full network management capabilities through an
easy-to-use web interface.
Package Checklist
The Cradle Access Point package includes:
• WA4101-Cradle
• RJ-45 Category 5 network cable
• AC power adapter
• Quick Installation Guide
• Management Guide CD
Inform your dealer if there are any incorrect, missing or damaged parts. If possible,
retain the carton, including the original packing materials. Use them again to repack
the product in case there is a need to return it.

Introduction
1-2
1
Hardware Description
Front Panel
Back Panel
Ethernet Port DC-IN Power Socket Reset Button

Hardware Description
1-3
1
Wi-Fi Phone Cradle
The WA4101-Cradle accepts an Edge-Core Wi-Fi Phone in its cradle for charging
the battery. When the device is powered on, just place the phone in the cradle and
charging starts immediately.
LED Indicators
The access point includes three status LED indicators, as described in the following
figure and table.
Ethernet Port
The access point has one 10BASE-T/100BASE-TX RJ-45 port that can be attached
directly to 10BASE-T/100BASE-TX LAN segments. Connect this port to the device
(cable or ADSL modem) that provides your Internet access, or to a LAN switch in a
network that has Internet access.
This port supports automatic MDI/MDI-X operation, so you can use straight-through
cables for all network connections to PCs, switches, or hubs.
LED Status Description
POWER On Green Indicates that the system is working normally.
WLAN On Indicates the 802.11g radio is enabled and transmitting or
receiving data through wireless links. The flashing rate is
proportional to network activity.
Off Indicates the 802.11g radio is disabled.
INTERNET On/Flashing Green Indicates a valid link on the Ethernet port and that the access
point is transmitting or receiving data. The flashing rate is
proportional to network activity.
Off The Ethernet port has no valid link.
Power 802.11g
Wireless
Link/Activity
Ethernet
Link/Activity

Introduction
1-4
1
Power Socket
The access point does not have a power switch. It is powered on when connected to
the AC power adapter, and the power adapter is connected to a power source. The
power adapter automatically adjusts to any voltage between 100-240 volts at 50 or
60 Hz. No voltage range settings are required.
Reset Button
The Reset button can be used to restart the access point or restore the factory
default configuration. If you press the button for less than 5 seconds, the access
point will restart. If you press and hold down the button for 5 seconds or more, any
configuration changes you may have made are removed and the access point is
restored to its factory default configuration.

2-1
Chapter 2: Hardware Installation
To install the WA4101-Cradle, follow these steps:
1. Select a Site – Choose a proper place for the access point. In general, the best
location is at the center of your wireless coverage area, within line of sight of all
wireless devices. For optimum performance, consider these points:
• Mount the access point as high as possible above any obstructions in the
coverage area.
• Avoid mounting next to or near building support columns or other obstructions
that may cause reduced signal or null zones in parts of the coverage area.
• Mount away from any signal absorbing or reflecting structures (such as those
containing metal).
• Avoid radio interference by mounting away from other 2.4 GHz devices, such as
other 802.11b or g wireless devices, regular cordless phones, and microwave
ovens.
2. Mount the Access Point – The access point is designed to be mounted on any
horizontal surface, such as a desktop.
3. Connect the Power Cord – Connect the power adapter to the access point,
and plug the power adapter into an AC power outlet.
Warning: Use ONLY the power adapter supplied with the access point.
Otherwise, the product may be damaged.
4. Observe the Indicator LEDs – When you power on the access point verify that
the POWER LED turns on and that the other LED indicators start functioning as
described under “LED Indicators".
5. Connect the Ethernet Cable – The access point can be connected to any 10
or 100 Mbps Ethernet network device, such as a cable or ADSL modem, or a
network switch. Connect your network to the RJ-45 port on the back panel
using category 3, 4, or 5 UTP Ethernet cable. When the access point and the
connected device are powered on, the INTERNET LED should turn on
indicating a valid network connection. If the INTERNET LED fails to turn on,
refer to “Troubleshooting”.
Note: The RJ-45 port on the access point supports automatic MDI/MDI-X operation, so
you can use straight-through cables for all network connections to PCs, switches,
or hubs.

Hardware Installation
2-2
2

3-1
Chapter 3: Initial Configuration
The WA4101-Cradle offers a user-friendly web-based management interface for the
configuration of all the unit’s features. Any PC with a wired or wireless connection to
the unit can access the management interface using a web browser, such as
Internet Explorer (version 5.0 or above). The initial configuration steps can be made
through the web browser interface using the Setup Wizard.
Connecting to the Web Interface
It is recommended to make the initial changes by connecting to the web
management interface through a wired connection to the access point’s Ethernet
port using the default IP (Internet Protocol) address of 192.168.2.1. Alternatively,
you can connect to the web interface through a wireless connection. Either method
may require changing the IP address settings of the PC.
The following procedure shows how to access the web interface from a PC
connected to the access point’s Ethernet port:
1. Place the access point close to the PC that you will use for configuration. It
helps if you can see the front panel LEDs of the access point while working on
your PC.
Figure 3-1. Connecting to the Web Management Interface
2. Connect the network port of your PC to the access point’s Ethernet port, start
your PC (if it is not already running), connect power to the access point and,
when your PC has finished its start-up sequence, verify that you have a link by
checking the LEDs on the front-panel of the access point.
3. Set your PC’s IP address to be on the same subnet as the access point. The
default IP address of the access point is 192.168.2.1 and the subnet mask is
AP’s Default IP Address 192.168.2.1
PC’s IP Address 192.168.2.x
Direct Ethernet
Cable Connection

Initial Configuration
3-2
3
255.255.255.0, so the PC and access point are on the same subnet when they
both have addresses that start 192.168.2.x. If the PC and access point are
already on the same subnet, proceed directly to step 4. Otherwise, you must
manually set the PC’s IP address to 192.168.2.x (where “x” can be any number
from 2 to 255). If you are unfamiliar with this process, see “Changing the PC’s
IP Address” below.
4. Open your web browser and enter the address http://192.168.2.1. If your PC is
properly configured, you will see the login page of your access point. If you do
not see the login page, check your settings and repeat step 3.
5. Proceed to the following sections for information on logging into the web
interface and starting the Setup Wizard.
Management Access Through a Wireless Connection
You can also access the web management interface from a PC using a wireless
connection. Follow these steps:
1. Ensure your PC is equipped with an 802.11g or 802.11b wireless adapter and
has a WLAN utility installed.
2. Set your PC’s IP address to be on the same subnet as the access point. The
default IP address of the access point is 192.168.1.254 and the subnet mask is
255.255.255.0, so the PC and access point are on the same subnet when they
both have addresses that start 192.168.1.x. If the PC and access point are
already on the same subnet, proceed directly to step 3. Otherwise, you must
manually set the PC’s IP address to 192.168.1.x (where “x” can be any number
from 1 to 253). If you are unfamiliar with this process, see “Changing the PC’s
IP Address” below.
3. Start your PC's WLAN utility and search for available wireless networks.
4. Find the wireless network named "Edge-Core 1" and connect to it. (Be sure the
access point is already powered on and the WLAN LED is flashing.)
5. Open your web browser and enter the IP address 192.168.1.254 in the address
bar. The access point login page should display. If you do not see the login
page, check your PC's settings and repeat step 3.
Changing a PC’s IP Address
To change the IP settings of your PC:
1. On Windows® XP, go to Start, then Network Connections. Or, find Network
Connections on the Control Panel window.
2. Right-click the icon for the network connection you want to change, and then
click properties.

Changing a PC’s IP Address
3-3
3
3. On the General tab, under This connection uses the following items, select
Internet Protocol (TCP/IP), and then click Properties.
4. In the Internet Protocol (TCP/IP) Properties dialog box, click Use the
following IP address.
5. For IP address, Subnet mask, and Default gateway, type your intended
settings.
6. Click OK to save the changes and then click OK again to close the Properties
dialog box.

Initial Configuration
3-4
3
Logging into the Web Interface
In the web browser’s address bar, type the default IP address: http://192.168.2.1.
The web browser displays the access point’s login page.
The default Username and Password is “Edge-Core.” Click LOGIN to access the
web management interface.
Note: It is strongly recommended that you change the default user name and password.
If the default values are not changed, the management interface is not protected
and anyone that can connect to the access point may be able to compromise your
network security. For information on changing the user name and password, see
“Administration” on page 4-7.
Figure 3-2. Login Page

Logging into the Web Interface
3-5
3
The home page displays the Main Menu. There are two options available, you can
configure the basic features of the access point using the Setup Wizard’s simple
steps, or you can configure all features in detail using the Advanced Setup menu.
Figure 3-3. Home Page

Initial Configuration
3-6
3
Using the Setup Wizard
There are only a few basic steps you need to set up the access point and provide a
connection for your Wi-Fi phone and network access for other wireless stations.
The Setup Wizard takes you through configuration procedures for the general
network settings, such as IP configuration, wireless network name (Service Set
Identifier), and wireless security. Follow these steps:
1. Launch the Setup Wizard – Click “Start with Setup Wizard” on the home page.
2. Network Setting – Sets the access point’s IP address assignment method and
configures the local Dynamic Host Configuration Prototcol (DHCP) server and
Network Address Translation (NAT) settings.
Figure 3-4. Setup Wizard - Network Setting
There are three basic methods for configuring the access point’s IP address:
•Dynamic IP — The IP address is assigned automatically from a home
gateway router or other device that has a DHCP server feature.
•PPPoE — The IP address is assigned automatically from an Internet service
provider (ISP) through an ADSL modem using Point-to-Point Protocol over
Ethernet (PPPoE). If your ISP has provided you with a user name and
password, enter these in the corresponding text boxes under PPPoE Setting.
•Static IP — The IP address is assigned manually by the user. This may be
required if your access point is connected to a home gateway router or other
device that does not support a DHCP server.