EdilKamin IDRO 50 Quick start guide

IDRO 50 - 70 - 100
I Installazione, uso e manutenzione pag. 2
UK Installation, use and maintenance pag. 18
F Installation, usage et maintenance pag. 34
E Instalación, uso y mantenimiento pag. 50
D Installations-, Betriebs- und Wartungsanleitung pag. 66
NL Installatie, gebruik en onderhoud. pag. 82
IDRO 50 - 50/CS - 70 - 100
ante fisse
IDRO 70 - 100
portellone
DIREZIONE CENTRALE : EDILKAMIN S.p.A.
www.edilkamin.com

18
Dear Sir / Madam,
Thank you for having chosen IDRO 50-70-100.
You are kindly asked to read through this information booklet before using the fireplace in order for you to make use of all its
features in total safety.
For further clarification or assistance, please contact the Dealer.
Please note that a qualified dealer MUST install the fireplace as is stipulated in the Italian Ministerial Decree No. 37 ex Italian Law
No. 46/90.
For installations implemented outside Italy, please refer to the local regulations in the country of use. The manufacturer cannot be
held liable for any damage caused as a result of incorrect installation, incorrect maintenance procedures and improper use.
IMPORTANT WARNINGS:
The thermo fireplace must never function without water in the system.
It can be damaged if it is ignited with no water in the system.
• The thermo fireplace is designed to heat water by means of automatic combustion of wood in the hearth.
• The only hazards that can derive from using the thermo fireplace pertain to non-compliance with the installation regulations,
direct contact with live electrical parts (external), contact made with the fire and hot parts or foreign substances being put in the
fireplace.
• No flammable products are to be used to clean the smoke channel.
• The hearth must only be cleaned with a vacuum cleaner when COLD.
• The glass can be cleaned when COLD with a suitable product (e.g. GlassKamin) and a cloth. Do not clean when hot.
• The exhaust pipes and the door become very hot when the thermo fireplace is used.
• Do not place anything, which is not heat resistant close to the thermo fireplace.
• NEVER use liquid fuel to ignite the thermo fireplace or to rekindle the embers.
• Do not obstruct the air inlets in the room where the fireplace is installed or the air inlets of the thermo fireplace itself.
• Do not wet the thermo fireplace and do not go near electrical parts with wet hands.
• Do not use reducers on the smoke exhaust pipes.
• The thermo fireplace must be installed in a place which is suitable for fire prevention and equipped with all that is required (power
and air inlets/outlets) for it to function properly and safely (refer to the indications given in these technical specifications).
WARNING:
In the list of parts, a code number is given and this must be quoted if a request for spare parts is made.
Declaration of conformity
The undersigned EDILKAMIN S.p.a. with head office headquarters at Via Vincenzo Monti 47 - 20123 Milan - Italy - VAT IT00192220192
Declares under its own responsability as follows:
The wood Thermo Fireplaces specified below is in accordance with the 89/106/EEC (Construction Products)
THE WOOD THERMO FIREPLACES, trademark EDILKAMIN, called IDRO 50-70-100
YEAR OF MANUFACTURE: Ref. Data nameplate SERIAL NUMBER: Ref. Data nameplate
The compliance with the 89/106/EEC directive is besides determined by the compliance with the European standard:
UNI EN 13229:2006
Also declares as follows:
The wood Thermo Fireplaces IDRO 50-70-100 is in compliance with the requirements of the European directives:
2006/95/EEC - Low voltage directive
2004/108/EEC - Electromagnetic compatibility directive
EDILKAMIN S.p.a. will decline all responsability of malfunctioning or damage to the equipment in case of unauthorized substitution, assembly or
modifications of any sort on the said equipment on the part of non-EDILKAMIN S.p.a. personnel.
ENGLISH

19
ENGLISH
TECHNICAL DATA
Thermal output (burnt) kW 23 30 35
Power output kW 18 23 27
Overall efficiency % 78,2 78,4 78
Efficiency to the water % ~ 70 ~ 70 ~ 70
Optimal wood consumption kg/h 5,5 7 8
Total weight including the packaging (min-max) kg 171/189 184/230 251/302
ø female smoke outlet cm 18 20 25
ø stainless steel chimney flue for a height ranging from 3 to 5 m cm 20 25 25
ø stainless steel chimney flue for a height ranging from 5 to 7 m cm 18 22 25
ø stainless steel chimney flue for a height exceeding 7 m cm 18 20 22
ø external air inlet cm 10 10 10
Water capacity litres 60 70 90
Maximum operating pressure bar 1,5 1,5 1,5
Hot sanitary water production (kit 1-3-n3-n3bis-6) * l/min ** 10 12 1 4
Heating capacity *** m3440 560 660
System return inches 1” 1”¼ 1”¼
System flow inches 1” 1”¼ 1”¼
70
50/50CS 100
A
The fireplace must be installed with an open tank
(EXCEPT FOR IDRO 50/CS).
The water of the radiator circuit warms up, circulates in the
heat exchanger pipe (4) and the hollow space (A) and
skims along the semi-circular wall. The hollow space is
created by using thick steel sheet metal.
4
*boiler temperature is 70°
** (ΔT=25K)
*** Insulation in accordance with the Legislative Decree 192/2005 ex Italian Law 10/91 and subse-
quent changes together with an expected heat output of 35 Kcal/m³ per hour.
IDRO 100
door
IDRO 50
IDRO 50 CS
fixed door
leaf
IDRO 70
fixed door
leafs
IDRO 70
door
IDRO 100
fixed door
leafs
thermal insulation
on the vaulted top
(implemented by the
client)
Specifications
Ø 20
55
18
66
2
64
77 5
65
138
Ø 25
77
80
3
138,5
18 55 65,5
99
81
Ø 25
55
18
78
2
81
94
65
138
5
Ø 18
55
18
64
2
64
77 5
65
138
Ø 20
55
18
65
68
3
64
80 8
65,5
138,5
93
105
8
66
68
80

ENGLISH
20
GENERAL SAFETY REGULATIONS
• THE THERMO FIREPLACE MUST NEVER
FUNCTION WITHOUT WATER IN THE SYSTEM.
• THE THERMO FIREPLACE CAN BE DAMAGED IF IT
IS IGNITED WITH NO WATER IN THE SYSTEM.
• The thermo fireplace is designed to heat water by
means of wood combustion in the hearth.
• The only hazards that can derive from using the
thermo fireplace pertain to non-compliance with the
installation instructions, direct contact with live
electrical parts (inside), contact made with the fire and
hot parts or foreign substances being put in the
fireplace.
• For the thermo fireplace to function properly
installation must be carried out according to the
instructions given in this booklet and the door must
only be opened to refill the hearth with wood.
• Never put foreign substances in the hearth or in the
tank.
• No flammable products are to be used to clean the
smoke outlet channel.
• The glass can be cleaned when COLD with a suitable
product (e.g. GlassKamin) and a cloth. Do not clean
when hot.
• The exhaust pipes and the door become very hot
when the thermo fireplace is used.
• Do not place anything that is not heat resistant close to
the thermo fireplace.
• NEVER use liquid fuel to ignite the thermo fireplace or
to rekindle the embers.
• Do not obstruct the external air inlets in the room
where the fireplace is installed or the air inlets of the
thermo fireplace itself.
• Do not wet the thermo fireplace and do not go near the
electrical parts of the system with wet hands.
• Do not use reducers on the smoke exhaust pipes.
• The thermo fireplace must be installed in a place that
is suitable against fire hazards and equipped with all
that is required (power and air inlets/outlets) for it to
function properly and safely.
• The thermal relief valve (supplied by Italiana Camini) must be connected to
the cooling circuit with a minimum pressure of 1.5 bar.
AL=P= coil power supply, always with a minimum pressure of 1.5 bar
• KITS 5 and 6 must be installed within a MAX distance of 150 cm from the
fireplace.
• Another expansion tank must be installed specifically for the thermo
fireplace in accordance with the volume of water of the system.
• The safety valve and the thermal relief valve must be checked at least once a
year by qualified personnel in accordance with Italian Law No. 46/90
Litres ?
1 Year
MAX 1,5 m
NO YES
ONLY THERMO FIREPLACES THAT HAVE A THERMAL RELIEF VALVE WHICH
ACTUATES THE COIL CAN BE INSTALLED ON CLOSED TANK SYSTEMS
Installations with a closed tank:
• The installer is responsible for the correct installation of the system, which is
to be compliant with UNI standards 10683/2005 – 9615/90 – 10412:2
• The entire process must be carried out by qualified personnel in accordance
with Italian Law No. 46/90
(VALID ONLY FOR IDRO 50/CS)
MIN.
1,5 bar

ENGLISH
21
CLOSED TANK additional regulations to those specified above
(VALID ONLY FOR IDRO 50/CS)
OPEN TANK
- Be careful not to exceed 1.5 bar when
filling the system.
- All the vents of the radiators must be ope-
ned during this phase so as to prevent
air pockets from forming in the system,
which would obstruct the circulation of
water.
- Only if a thermal relief valve actuates the
coil can the fireplace be installed on a
CLOSED TANK system.
- Consider the necessity of installing another
CLOSED TANK.
- Make sure the drain is connected to the
coil and the power supply is at least 1.5 bar.
- The upstream pressure of the cooling
circuit must be at least 1.5 bar (UNI
10412/2 point 6.2).
- The connections, commissioning and
verification of proper operation of the fi-
replace must be carried out by
qualified personnel, who can implement
all connections in accordance with the
laws in force, particularly with Italian D.M
37 Law No. 46/90, apart from com-
plying with these instructions.
- The thermo fireplace and the system are
filled with water that flows from the water
inlet pipe (the diameter must not be less
than 18 mm) to the open expansion tank.
- All the vents of the radiators must be ope-
ned during this phase so as to prevent air
pockets from forming in the system, which
would obstruct the circulation of water.
NB:
- The open tank should be placed higher
than 3 m from the highest radiator and
lower than 15 m from the thermo
fireplace outlet.
- Connect the drains of the thermal relief
valve (TRV) and the safety valve (SV)
(diagrams are found on the following
pages).
- The flow test of the system must be carried
out with the expansion tank open.
- It is recommended to install a 6 bar safety
valve on the hot sanitary water circuit so
as to drain any excessive increase in the
volume of the water in the heat
exchanger.
- Place all the components of the system
(circulator, heat exchanger, valves, etc.)
in easily accessible points for routine and
special maintenance procedures.
- It is recommended to prepare thermal
insulation on the vaulted top part of the
boiler.
WATER TREATMENT
- If need be, antifreeze, descaling and
anticorrosive solutions are to be added to
the water. A softener must be used if the
hardness of the water used to refill and
top-up the system exceeds 35°f (French
degrees).
Please refer to UNI 8065-1989 standard
(water treatment in domestic heating
systems).
- In any case, the tank must be high
enough to create a greater pressure than
that produced by the pump (circulator).
- The system must never be filled
directly from the water mains as the
pressure may be greater than that
stipulated on the data plate of the thermo
fireplace.
- The safety pipe to the expansion tank must
allow the water to flow freely, must not
have taps and must be insulated properly.
- The water inlet pipe must not have taps
nor curves.
- The maximum operating pressure must not
exceed 1.5 bar
- The testing pressure is 3 bar.
- In places that reach very low temperatures,
antifreeze liquid must be added to the
water in the system.
- Never ignite the fire in the thermo fireplace
(not even as a test) unless the system is
filled with water as this could cause
irreparable damage.
GENERAL SAFETY REGULATIONS

ENGLISH
22
INSTALLATION INSTRUCTIONS
45°
45°
Chimney flues and chimneypot
The thermo fireplace smoke outlet has a cir-
cular crosssection so that stainless steel pipes
can be used.
If the chimney flue inlet is not vertically above
the thermo fireplace, the connection from the
fireplace to the flue must not have a narro-
wing section or inclinations greater than 45°
(fig.A ).
If the chimney flue is not brand new or too
big, it is recommended to fit in stainless tubes
of an appropriate diameter and with suitable
insulation.
If the chimney flue is installed outside, it is
recommended to use an insulated, double
walled, stainless steel flue.
The characteristics of the construction must
be suitable to withstand a smoke temperatu-
re of at least 450° C, with particular referen-
ce to the mechanical resistance, insulation
and the gas tight sealing.
The junction of the steel flue inlet and the
smoke outlet of the fireplace must be sealed
with high temperature mastic.
The fundamental characteristics of the
chimneypot are:
- an internal cross-section at the base, which
is the same as that of the chimney flue.
- an outlet cross-section which is no smaller
than twice that of the chimney flue.
- its position must be high enough to catch
the wind and avoid downdraft areas in
turbulent wind.
In addition to that mentioned above,
please consider the indications stipulated
in UNI 10683/2005 standard,
paragraph 4.2: “connection to the smoke
outlet system” and its subsections.
max.45° NO
NO
fig.A
23
1 2 3
Important advice regarding the
installation
Other than that described in this documen-
tation, you are also asked to note the follo-
wing UNI standards:
- No. 10683/2005 - firewood heat gene-
rators: installation requirements
- No. 9615/90 - calculating the internal
dimensions of fireplaces
- No. 10412:2 - hot water heating
systems. Specific safety requirements for
systems provided with residential solid fuel
burning appliances and combined boiler,
not exceeding a total nominal heat input of
35 kW.
Particularly:
-Before carrying out any assembly it is
important to verify compatibility of the
appliance, as stipulated in UNI
10683/2005 standard, paragraphs 4.1 /
4.1.1 / 4.1.2.
-When assembly is completed, the
installer must implement “start-up opera-
tions” and issue documentation as required
by UNI 10683/2005 standard in para-
graphs 4.6 and 5, respectively.
-The connections, commissioning and
verification of proper operation of the
fireplace must be carried out by qualified
personnel, who can implement the electri-
cal and plumbing connections as required
by UNI standards
10683/2005, paragraph 4.5 and
10412:2, apart from complying with these
assembly instructions.
- Verification must be carried out with the
fireplace on and after having been on for a
couple of hours, before covering the fire-
place, so that you can intervene if need be.
After which, the finishing operations such
as:
- setting-up the fireplace mantel
- mounting the fireplace covering
- pilasters, painting, etc.
are carried out, once the tests are comple-
ted successfully.
Consequently, Italiana Camini does not
accept responsibility for expenses deriving
from demolition as well as construction
even if either occurs as a result, after
having replaced any damaged parts of the
fireplace.
External air inlet (optional)
An external connection with a 10 cm
diameter crosssection throughout
(refer to the technical table) is absolu-
tely necessary for the thermo fireplace
to function properly and is therefore
imperative for this to be implemented.
This connection must link the air adjustment
mechanism (E), delivered separately. It can
be installed on either the left side or the
right side of the thermo fireplace.
This can be made of a flexible aluminium
pipe.
Ensure that the points where there may be
dispersion of air are sealed well.
The air adjustment mechanism (E) can be
removed and mounted on the right side of
the thermo fireplace.
It is recommended to place a protection
grille on the outer part of the air inlet chan-
nel, however, ensure that this does not
reduce the cross-section.
For distances longer than 3 m or with
bends, increase the given cross-section by a
minimum of 10% to a maximum of 20%.
The intake of external air must enter at floor
level (it cannot enter from above).
E
fig.1
E
1

ENGLISH
23
Transporting the fireplace
In order to facilitate transportation, the firepla-
ce can be made lighter by removing the follo-
wing:
- the base of the hearth and the ash grill made
of cast iron and the ash-pan.
- the door.
Fireplace
To decide upon the exact positioning of the
fireplace, it is important to verify which cove-
ring will be applied.
The positioning is implemented according to
the model chosen (refer to the installation
instructions found inside the packaging of each
fireplace covering).
Always ensure the thermo fireplace is level
during the installation process.
- Drill a hole into the wall or the flooring for the
external air intake and connect the air adju-
stment mechanism to the hole as described in
the chapter called “external air inlet”.
- Use a stainless steel flue to connect the fire-
place to the chimney flue, adhering with the
diameters indicated in the specifications table
and the guidelines given in the chapter called
“chimney flues”.
- Verify that all moving parts function properly
before setting the thermo fireplace covering in
place.
- This system must be tested and ignited
for the first time before the covering is
set in place.
Installation of the fireplace
covering, fireplace mantel and
ventilation outlets (Fig. F)
The base of the fireplace covering must allow the
internal air to be recycled. Failing to do so, the
fireplace will not function properly with possible
smoke backflow.
Therefore, suitable slots or apertures must be
made for the air to pass through.
Parts of the fireplace covering that are made of
marble, stone and bricks must be mounted with a
small gap between them and the fireplace so as to
prevent possible breakage due to
expansion and excessive overheating.
Wooden parts must be protected by fire resistant
panels and no part must touch the thermo fireplace,
- Close the door
- Adjust the combustion setting via the damper
control at the front.
- Set the thermostat on the electronic regulator
(*) at a temperature between 50 and 70° C.
- The 3-way valve (*) diverts the water flow direc-
tly to the thermo fireplace; when the set tempe-
rature is reached, the 3- way valve (*) diverts the
flow to the system.
- When the door is closed, the damper by-pass
automatically diverts the combustion smoke,
thus improving the efficiency.
- When the door is opened, the damper by-
pass opens automatically, allowing the smoke
to reach the smoke flue directly, preventing it
from coming out of the inlet.
(*) these components of the system are to be
provided by the installer.
During the combustion process
If the water temperature exceeds 90° C becau-
se of too much wood being placed in the
hearth, the thermal relief valve will be activated
and the acoustic signal heard.
In this case you must proceed as follows:
- Wait until the temperature is lower than 80°
C; check the warning lights on the electronic
regulator.
- The hot water tap can be opened to speed up
the cooling process if the thermo fireplace is
equipped with hot sanitary water.
Adjusting the air
- The damper control found on the external air
inlet (refer to Fig. 1 on pg. 6), regulates the
amount of primary air that is necessary for the
combustion process. Pushing the knob will
close the external air inlet and pulling the knob
will open it.
Maintenance
Cleaning the hearth
- Fouling that tends to accumulate on the inter-
nal walls of the thermo fireplace decreases the
efficiency of heat transfer.
- It is therefore necessary to clean the fireplace
regularly, by bringing the water temperature to
80 / 85° C to soften the fouling and then
remove this with a steel spatula.
Cleaning and replacing the glass
- Use an appropriate spray for ceramic glass to
clean the glass.
- The glass must be cleaned when cold.
- If the glass must be replaced, remove the
self-tapping screws and fibreglass gasket befo-
re removing the glass holder profiles.
- Ensure the gasket is inserted in place before
setting the glass back in place.
on the contrary, there must be an appropriate
distance of at least 1 cm to allow the air to
flow, preventing heat accumulation.
The fireplace mantel can be made of fireproof
plasterboard panels or gypsum board.
Air should be allowed to flow inside the firepla-
ce mantel (through the gap between the door
and the beam). Through convective motion,
the air will flow out from the grille installed
at the top, resulting in heat recovery and pre-
venting excessive overheating.
The fireplace mantel must have appropriate
openings to carry out maintenance on the
fittings.
In addition to that mentioned above,
please consider the indications stipula-
ted in the UNI 10683/2005 standard,
paragraphs 4.4 and 4.7: “insulation,
finishing, fireplace covering and safety
recommendations”.
Insulating mats must be applied when
using an installation KIT so as to protect
it from the heat radiation emitted by the
fireplace.
Important advice when using the
fireplace
- It is important to ensure that there is
water in the thermo fireplace and the
system before igniting the fireplace. It is
recommended to connect the inlet and
outlet pipes as shown in the diagrams.
- The maximum operating pressure must not
exceed 1.5 bar
- The Company is responsible for the proper
functioning of the product only if this is han-
dled in accordance with the documentation
supplied with the product itself.
- First ignition (or re-igniting):
remove any ash residue from the hearth.
Practical advice
- It is recommended to keep the radiators clo-
sed in the room where the thermo fireplace is
installed since the heat radiated from the ope-
ning of the fireplace itself is enough.
- An incomplete combustion process causes
excessive fouling on the heat exchanger pipe.
To prevent this you must:
- burn dry wood.
- ensure the hearth contains a bed of embers
and burning carbon before adding more
wood.
- place larger logs together with smaller ones.
Igniting the fireplace
- Ensure that at least one radiator is always
open.
- Actuate the switches of the electronic regulator.
- Place a pile of medium-thin dry wood in the
thermo fireplace and ignite the fire.
- Wait a few minutes until it reaches sufficient
combustion.
INSTALLATION AND USE INSTRUCTIONS
FIREPLACE MANTEL
METAL COWL
THERMAL INSULATION ON
THE VAULTED TOP PART
(implemented by the client)
WOODEN BEAM
FRONT COVER MADE OF
NON-FLAMMABLE MATERIAL
* optional components

ENGLISH
24
SYSTEM FOR AN OPEN TANK INSTALLATION
AN EXAMPLE OF A HYDRAULIC SYSTEM FOR A THERMO FIREPLACE WITH HOT SANITARY WATER PRODUCTION USING KIT 1
TC
Kit 1 is designed to facilitate the work carried out by the installers. In fact, it consists of all the necessary components for the product to be
properly installed.
NB: insulating mats must be applied so that the components of the kit are well-protected from the heat radiation emitted by the
fireplace.
ACS: Hot Sanitary Water
AF: Cold Water
EV: 3-way Solenoid Valve
F: Flow Switch
MI: System Flow
NA: Normally Open
NC: Normally Closed
P: Pump (circulator)
RA: Radiators
RE: Electronic Regulator
RI: System Return
S: Drain
Sc 20: 20-plate Heat Exchanger
ST: Temperature Sensor
TC: Thermo Fireplace
V: Valve
VE: Open Expansion Tank
VSP: 1.5 bar Pressurized Safety Valve
VST: Thermal Relief Valve
Ja: Automatic Relief Valve
1” Male-Female Brass Collector
1” Ball Valve
Circulator with 1½” Fasteners (219660)
1” Check Valve (261910)
1” Male-Female 3-way Solenoid Valve (143330)
Copper Fittings
30-plate Heat Exchanger for heat transfer with
the gas boiler circuit (216620)
20-plate Heat Exchanger for hot sanitary water
production (205270)
¾” Thermal Relief Valve (72940)
¾” 1.5 bar Safety Valve (143260)
Flussostato (220830)
½” Thermometer Well + Sensor (175960)
Electronic Regulator (220780)
¾” System Return
¾” System Flow
¾” Fireplace Return
1” Fireplace Flow
½” Cold Sanitary Water
½” Hot Sanitary Water
The sales codes are in brackets ( )
1
2
3
4
5
6
7
C
D
F
11
12
13
B
8
9
10
A
E
Components KIT 1
KIT 1
ON
OFF
20 - 80° C
Circulator Setting
Fuse
Display
20 - 80° C
Valve Setting
Flow Switch
Attention: Connect the normally closed contact
Power Supply
230 Vac
Circulator
3-way valve
Circulator enabled
Overheating alarm
3-way valve Enable
Disable
Acoustic
Alarm
Sensor
(insert in the
appropriate
well)
SELECTOR FUNCTIONS
Selector: OFF Everything is switched off
Selector: MAN Driven Circulator
Valve is set
Selector: AUTO Circulator is set
Valve is set
Alarm selection No acoustic signal in the
OFF position
Electrical Connections
KIT 1 code 261880
THE INLET AND OUTLET PIPES MUST BE CROSSED FOR THE KIT TO FUNCTION PROPERLY
Collector
Regulator
(included in the kit)
20-plate heat
exchanger
Safety pipe Ø> 28mm
Inlet pipe Ø> 18mm

ENGLISH
25
AN EXAMPLE OF A HYDRAULIC SYSTEM FOR A THERMO FIREPLACE THAT DOES NOT PRODUCE HOT SANITARY WATER BUT HAS A WALL MOUNTED BOILER USING KIT 2
Kit 2 is designed to facilitate the work carried out by the installers. In fact, it consists of all the necessary components for the
product to be properly installed.
NB: insulating mats must be applied so that the components of the kit are well-protected from the heat radiation emitted by the
fireplace.
1” Male-Female Brass Collector
1” Ball Valve
Circulator with 1½” Fasteners (219660)
1” Check Valve (261910)
1” Male-Female 3-way Solenoid Valve (143330)
Copper Fittings
30-plate Heat Exchanger for heat transfer with
the gas boiler circuit (216620)
20-plate Heat Exchanger for hot sanitary water
production (205270)
¾” Thermal Relief Valve (72940)
¾” 1.5 bar Safety Valve (143260)
Flow Switch (220830)
½” Thermometer Well + Sensor (175960)
Electronic Regulator (220780)
¾” System Return
¾” System Flow
¾” Fireplace Return
1” Fireplace Flow
½” Cold Sanitary Water
½” Hot Sanitary Water
1
2
3
4
5
6
7
C
D
F
11
12
13
B
8
9
10
A
E
KIT 2
SELECTOR FUNCTIONS
Selector: OFF Everything is switched off
Selector: MAN Driven Circulator
Valve is set
Selector: AUTO Circulator is set
Valve is set
Alarm selection No acoustic signal in the
OFF position
KIT 2 code 261890
AF: Cold Water
CA: Wall Mounted Boiler
MI: System Flow
P: Pump (circulator)
RA: Radiators
RE: Electronic Regulator
RI: System Return
S: Drain
Ja: Automatic Relief Valve
Sc 30: 30-plate Heat Exchanger
ST: Temperature Sensor
TC: Thermo Fireplace
V:Valve
VE: Open Expansion Tank
VR: Check Valve
VSP: 1.5 bar Pressurized Safety Valve
VST: Thermal Relief Valve
TC
The sales codes are in brackets ( )
ON
OFF
Enable
Disable
Acoustic
Alarm
Minimum temperature setting
for circulators to be actuated
20 – 80° C
Fuse
Display
20 - 80° C
Circulators Setting
Sonda
(inserire
nell’apposito
pozzetto)
Circolatore B
Circolatore A
Circulators enabled
Overheating alarm
Circulators Setting
Alimentazione
230 Vac
Electrical Connections
Components KIT 2
THE INLET AND OUTLET PIPES MUST BE CROSSED FOR THE KIT TO FUNCTION PROPERLY
SYSTEM FOR AN OPEN TANK INSTALLATION
Collector
Safety pipe Ø> 28mm
Inlet pipe Ø> 18mm
Regulator
(included in the kit)
30-plate heat
exchanger

26
ENGLISH
Kit 3 is designed to facilitate the work carried out by the installers. In fact, it consists of all the necessary components for the product to be
properly installed.
NB: insulating mats must be applied so that the components of the kit are well-protected from the heat radiation emitted by the
fireplace.
1” Male-Female Brass Collector
1” Ball Valve
Circulator with 1½” Fasteners (219660)
1” Check Valve (261910)
1” Male-Female 3-way Solenoid Valve (143330)
Copper Fittings
30-plate Heat Exchanger for heat transfer with
the gas boiler circuit
(216620)
20-plate Heat Exchanger for hot sanitary water
production (205270)
¾” Thermal Relief Valve (72940)
¾” 1.5 bar Safety Valve (143260)
Flow Switch (220830)
½” Thermometer Well + Sensor (175960)
Electronic Regulator (220780)
¾” System Return
¾” System Flow
¾” Fireplace Return
1” Fireplace Flow
½” Cold Sanitary Water
½” Hot Sanitary Water
1
2
3
4
5
6
7
C
D
F
11
12
13
B
8
9
10
A
E
SELECTOR FUNCTIONS
Selector: OFF Everything is switched off
Selector: MAN Driven Circulator
Valve is set
Selector: AUTO Circulator is set
Valve is set
Alarm selection No acoustic signal in the
OFF position
KIT 3 code 261900
ON
OFF
Enable
Disable
Acoustic
Alarm
Circulator Setting
20 - 80° C
Fuse
Display
20 - 80° C
Valve Setting
Flow Switch
Attention: Connect the
normally closed contact
Power Supply
230 Vac
3-way valve
Circulator enabled
Overheating alarm
3-way valve
Circulator ACirculator B
Sensor
(insert in the
appropriate well)
Components KIT 3
The sales codes are in brackets ( )
Electrical Connections
TC
KIT 3
ACS: Hot Sanitary Water
AF: Cold Water
CA: Wall Mounted Boiler
EV: 3-way Solenoid Valve
F: Flow Switch
MI: System Flow
NA: Normally Open
NC: Normally Closed
P: Pump (circulator)
RA: Radiators
RE: Electronic Regulator
RI: System Return
S: Drain
Sc 20: 20-plate Heat Exchanger
Sc 30: 30-plate Heat Exchanger
TC: Thermo Fireplace
V: Valve
VE: Open Expansion Tank
VR: Check Valve
VSP: 1.5 bar Pressurized Safety Valve
VST: Thermal Relief Valve
Ja: Automatic Relief Valve
THE INLET AND OUTLET PIPES MUST BE CROSSED FOR THE KIT TO FUNCTION PROPERLY
SYSTEM FOR AN OPEN TANK INSTALLATION
Collector
Safety pipe Ø> 28mm
Inlet pipe Ø> 18mm
Regulator
(included in the kit)
30-plate heat
exchanger
20-plate heat
exchanger
AN EXAMPLE OF A HYDRAULIC SYSTEM FOR A THERMO FIREPLACEITH HOT SANITARY WATER PRODUCTION AND A WALL MOUNTED BOILER USING KIT 3

Kit N3 is designed to facilitate the work carried out by the installers. In fact, it consists of all the necessary components for the product to
be properly installed.
NB: insulating mats must be applied so that the components of the kit are well-protected from the heat radiation emitted by the
fireplace.
KIT N3 code 627690
Components KIT N3
CA: Wall Mounted Boiler
PR: Pump (circulator)
P1: Primary circuit pump
RE: Electronic regulator
TA: Room thermostat
VE: Expansion Tank
Ja: Air refief Valve
V:Intercept valve
VR: Retaining valve
ST: Temperature Sensor
F: Flow switch
Sc: Heat plate exchanger
EV: 3-way solenoid valve
RI: Heating system return
RA: Radiators
MI: Heating system flow
AF: Cold water
ACS: Hot sanitary water
S: Drain
SYSTEM FOR AN OPEN TANK INSTALLATION
AN EXAMPLE OF A HYDRAULIC SYSTEM FOR A THERMO FIREPLACEITH HOT SANITARY WATER PRODUCTION AND A WALL MOUNTED BOILER USING KIT N3
Heating system return G 3/4”
EDILKAMIN generator flow G 3/4”
EDILKAMIN generator return G 3/4”
Heating system flow G 3/4”
Cold sanitary water inlet G 1/2”
Hot water return to the sanitary system G 1/2”
Safety valve - temperature and pressure (90 °C - 3bar)
Flow Switch
Air relief valve G 3/8”
EDILKAMIN generator circuit circulator
3-way heat exchanger
Intercept valve G 1”
Electronic regulator with wiring
Appropriate aperture for the cable duct to pass through
Power cable
Cables for the heating system circulator (phase, neutral, earth)
Temperature sensor
Room thermostat circuit
1
2
3
4
5
6
7
11
12
13
8
9
10
VE AF
SV
RE
RETE
ST
V
S
V
Tubo di carico Ø> 18 mm
Tubo di sicurezza Ø> 28 mm
V
CA
ACS
PR
F
ACS
AF
Ja
TA
P1
V
Vs
Sc
TCN
ELETTRICA
INT
VR V
VR
RETE
IDRICA
VR
VR
MI
RA
RI
V
COLLETTORE
VR
V
V
V
V
V
Circuito collegabile al
termostato ambiente
(a discrezione del cliente)
Da collegare necessariamente
al circolatore dell’impianto
di riscaldamento PR
1234
56
7
8
9
10
11
9
9
12
13
1
235
46
7
14
15 16 17
Passacavi
18
14
15
16
17
18
KIT N3
Collector
Safety pipe Ø> 28mm
Inlet pipe Ø> 18mm
Electricity
Mains
Water
Mains
Cable duct
circuit connected to
the room thermostat
(implemented by the
client)
must be connected to the
heating system circulator
Electrical Connections
Room thermostat
Electricity
Mains
sensor
Sanitary-heating enabled setting
Primary circulator enabled setting
Enabled alarm
Flow sensor
Heating pump
Primary circuit pump
THE INLET AND OUTLET PIPES MUST BE CROSSED FOR THIS TO FUNCTION PROPERLY 27
ENGLISH

ENGLISH
28
CA Wall Mounted Boiler
P2 Pump (circulator)
P1 Primary circuit pump
RE Electronic regulator
TA Room Thermostat
VE Expansion Tank
Ja Air Relief Valve
VIntercept valve
VRRetaining valve
ST Temperature Sensor
FFlow switch
Sc Heat Plate Exchanger
EV 3-way Solenoid Valve
RI Heating system return
RA Radiators
MI Heating system flow
AF Cold Water
ACS Hot Sanitary Water
SDrain
INT Main switch
TCN Contact Thermostat
KIT N3 BIS code 627860
Components KIT N3 BIS
SYSTEM FOR AN OPEN TANK INSTALLATION
AN EXAMPLE OF A HYDRAULIC SYSTEM FOR A THERMO FIREPLACE WITH HOT SANITARY WATER PRODUCTION AND A WALL MOUNTED BOILER USING KIT N3 BIS
Heating system return G 3/4”
EDILKAMIN generator flow G 3/4”
EDILKAMIN generator return G 3/4”
Heating system flow G 3/4”
Cold sanitary water inlet G 1/2”
Hot water return to the sanitary system G 1/2”
Sanitary hot water inlet to the gas boiler G 1/2”
Safety valve - temperature and pressure (90 °C - 3bar)
Flow Switch
3-way deviation solenoid valve
Air relief valve G 3/8”
EDILKAMIN generator circuit circulator
Heating system circuit circulator
Intercept valve G 1”
3-way heat exchanger
Electronic regulator with wiring
Appropriate aperture for the cable duct to pass through
Power cable
Temperature sensor
Room thermostat circuit
1
2
3
4
5
6
7
11
12
13
8
9
10
14
15
16
17
18
19
20
1
234
567
8
9
10
11
12
13 14
14
15
11
1111
1111
16
17
123
4
5
8
6
7
20
19
Passacavi
17
18
VE AF
SV
RE
ST
S
V
Tubo di carico Ø> 18 mm
Tubo di sicurezza Ø> 28 mm
CA
ACS
VR
MI
RA
RI
V
ACS
AF
Ja
TA
EV
P2
P1
V
V
Sc
FVs
RETE
ELETTRICA
INT
VR V
TCN
V
V
V
By-pass
VR
Sc
RETE
IDRICA
COLLETTORE
VR
V
V
V
V
V
Circuito collegabile al
termostato ambiente
(a discrezione del cliente)
KIT N3 BIS
Collector
Safety pipe Ø> 28mm
Inlet pipe Ø> 18mm
Electricity
Mains
Water
Mains
Cable duct
circuit connected to
the room thermostat
(implemented by the
client)
Kit N3 BIS is designed to facilitate the work carried out by the installers. In fact, it consists of all the necessary components for the product
to be properly installed.
NB: insulating mats must be applied so that the components of the kit are well-protected from the heat radiation emitted by the
fireplace.
Electrical Connections
Room thermostat
Electricity
Mains
sensor
Sanitary-heating enabled setting
Primary circulator enabled setting
Enabled alarm
Flow sensor
Heating pump
Primary circuit pump
THE INLET AND OUTLET PIPES MUST BE CROSSED FOR THIS TO FUNCTION PROPERLY

ENGLISH
29
SYSTEM FOR AN OPEN/CLOSED TANK INSTALLATION
AN EXAMPLE OF A HYDRAULIC SYSTEM FOR A THERMO FIREPLACE THAT PRODUCES AND STORES HOT SANITARY WATER AND HAS A WALL MOUNTED BOILER USING IDROKIT
IDROKIT is designed to facilitate the work carried out by the installers. In fact, it consists of all the necessary components for the product
to be properly installed.
ACS: Hot Sanitary Water
AF: Cold Water
AL: Water Mains Supply
C: Filling/Top-Up Section
CE: Electronic Panel
EV: 3-way Solenoid Valve
NA: Normally Open
NC: Normally Closed
GR: Pressure Reducer
Ja: Automatic Relief Valve
Jm: Manual Relief Valve
MI: System Flow
MT: Thermostatic Mixer
P: Pump (circulator)
RA: Radiators
RI: System Return
S: Drain
SC30: 30-plate Heat Exchanger
ST: Temperature Sensor
TC: Contact Thermostat
TM: Thermo Fireplace
V: Ball Valve
Vea: Open Expansion Tank
Vec: Closed Expansion Tank
VR: Check Valve
VSPT: Safety Pressure and Temperature Valve
VCA: Boiler
IDROKIT
A
B
C
D
E
1heating return
2gas boiler hot sanitary water
3thermo fireplace flow
4 drain
5 hot sanitary water
6 thermo fireplace return
7 heating flow
8 water mains
9 thermostatic mixer setting
10 synoptic panel
11 auxiliary socket for a room thermostat
1 2
34
5
67
8
10
9
A30-plate Heat Exchanger
Bprimary circulator (in the wood-fired version)
C50-litre boiler
Dheating system circulator
Eclosed expansion tank
Ffireplace covering for exposed installation
F
cm 45cm 44
cm 115
11
IDROKIT code 601740
TM
Collector
Safety pipe Ø> 28mm
Inlet pipe Ø> 18mm
THE INLET AND OUTLET PIPES MUST BE CROSSED FOR THIS TO FUNCTION PROPERLY

ENGLISH
30
AN EXAMPLE OF A HYDRAULIC SYSTEM FOR A THERMO FIREPLACE - ONLY HEATING USING KIT 5
Tra parentesi i codici di ven-
1
2
3
4
5
6
7
C
12
13
B
9
10
A
E
Components KIT 5
KIT 5
SELECTOR FUNCTIONS
Selector: OFF Everything is switched off
Selector: MAN Driven Circulator
Valve is set
Selector: AUTO Circulator is set
Valve is set
Alarm selection No acoustic signal in the
OFF position
Electrical Connections
KIT 5 code 280590
14
15
16
G
ON
OFF
20 - 80° C
Circulator Setting
Fuse
Display
20 - 80° C
Valve Setting
Power Supply
230 Vac
Circulator
3-way valve
Circulator enabled
Overheating alarm
3-way valve
Enable
Disable
Acoustic
Alarm
Sensor
(insert in the
appropriate well)
NB: Essential safety connections
safety valve connection
The sales codes are in brackets ( )
Water Mains Supply
Filling/Top-Up Section
3-way Solenoid Valve
Normally Open
Normally Closed
Filling unit
Automatic Relief Valve
Manual Relief Valve
Manometer
System Flow
Pump (circulator)
Radiators
Electronic Regulator
System Return
Drain
Temperature Sensor
Ball Valve
Closed Expansion Tank
Check Valve
Pressurised Safety Valve
Thermal Relief Valve
AL:
C:
EV:
NA:
NC:
GR:
Ja:
Jm:
MAN:
MI:
P:
RA:
RE:
RI:
S:
ST:
V:
Vec:
VR:
VSP:
VST:
SYSTEM FOR A CLOSED TANKINSTALLATION
1" Ball Valve
Thermal Relief Valve (72940)
Pressure Relief Valve (284220)
Circulator (219660)
Fittings with 1" Check Valve (284180)
¾" Male 3-way Solenoid Valve (283690)
Fittings
Temperature Relief Valve Nozzle
Closed Expansion Tank (283680)
½" Thermometer Well + Sensor (175960)
Electronic Regulator (220780)
3/8" Automatic Relief Valve (284150)
1/4" Manual Relief Valve (284170)
Manometer (269590)
Fireplace Flow
System return
Fireplace Return
Pressure Relief Valve
Temperature Relief Valve
Kit 5 is designed to facilitate the work carried out by the installers. In fact, it consists of all the necessary components for the product to be
properly installed.
NB: insulating mats must be applied so that the components of the kit are well protected from the heat radiation emitted by the fireplace.
Collector
Regulator and manometer
(included in the kit)
THE INLET AND OUTLET PIPES MUST BE CROSSED FOR THIS TO FUNCTION PROPERLY
(VALID ONLY FOR IDRO 50/CS)

ENGLISH
31
AN EXAMPLE OF A HYDRAULIC SYSTEM FOR A THERMO FIREPLACE WITH HOT SANITARY WATER PRODUCTION USING KIT 6
Kit 6 is designed to facilitate the work carried out by the installers. In fact, it consists of all the necessary components for the product to be
properly installed.
NB: insulating mats must be applied so that the components of the kit are well protected from the heat radiation emitted by the fireplace.
1
2
3
4
5
6
7
C
D
F
11
12
13
B
8
9
10
A
E
KIT 6
SELECTOR FUNCTIONS
Selector: OFF Everything is switched off
Selector: MAN Driven Circulator
Valve is set
Selector: AUTO Circulator is set
Valve is set
Alarm selection No acoustic signal in the
OFF position
KIT 6 code 280600
1" Ball Valve
Thermal Relief Valve (72940)
Pressure Relief Valve (284220)
Circulator (219660)
Fittings with 1" Check Valve (284180)
¾" Male 3-way Solenoid Valve (283690)
Fittings
20-plate Heat Exchanger for hot sanitary water
production (284300)
Temperature Relief Valve Nozzle
Closed Expansion Tank (283680)
Flow Switch (220830)
½" Thermometer Well + Sensor (175960)
Electronic Regulator (220780)
3/8" Automatic Relief Valve (284150)
1/4" Manual Relief Valve (284170)
Manometer (269590)
Fireplace Return
System Return
Fireplace Return
Cold Sanitary Water
Pressure Relief Valve
Hot Sanitary Water
Temperature Relief Valve
14
15
16
G
NB: essential safety connections
safety valve connection ACS:
AF:
AL:
C:
EV:
NA:
NC:
F:
GR:
Ja:
Jm:
MAN:
MI:
P:
RA:
RE:
RI:
S:
SC:
ST:
V:
Vec:
VR:
VSP:
VST:
Hot Sanitary Water
Cold Water
Water Mains Supply
Filling/Top-Up Section
3-way Solenoid Valve
Normally Open
Normally Closed
Flow Switch
Filling unit
Automatic Relief Valve
Manual Relief Valve
Manometer
System Flow
Pump (circulator)
Radiators
Electronic Regulator
System Return
Drain
Plate Exchanger
Temperature Sensor
Ball Valve
Closed Expansion Tank
Check Valve
Pressurised Safety Valve
Thermal Relief Valve
ON
OFF
20 - 80° C
Circulator Setting
Fuse
Display
20 - 80° C
Valve Setting
Flow Switch
Attention: Connect the
normally closed contact
Power Supply
230 Vac
Circulator
3-way valve
Circulator enabled
Overheating alarm
3-way valve
Enable
Disable
Acoustic
Alarm
Sensor
(insert in the
appropriate well)
Componenti KIT 6
The sales codes are in brackets ( )
Electrical Connections
SYSTEM FOR A CLOSED TANKINSTALLATION
Collector
Regulator and manometer
(included in the kit)
20-plate heat
exchanger
THE INLET AND OUTLET PIPES MUST BE CROSSED FOR THIS TO FUNCTION PROPERLY
(VALID ONLY FOR IDRO 50/CS)

ENGLISH
32
Operation
- Control device:
•Thermometer
- Protection device
(acoustic alarm system):
•Acoustic alarm (AA)
•Overheating alarm (SS)
This system intervenes when the water temperature exceeds 90° C and
warns the user to stop adding fuel.
The acoustic alarm can be disabled from the switch (AA).
However, the alarm remains enabled by means of the
overheating light (SS).
To restore the initial settings, the switch (AA) must be enabled after the
water temperature in the thermo fireplace has cooled down.
- Power supply device
(circulation system):
•
MAN-OFF-AUTO selector (S)
• Pump light (SP)
The pump remains on when in manual mode and off when in
OFF mode. When in AUTO mode, the pump is activated by the system
when the desired temperature is reached, by means of the internal setting
(RIC), which ranges from 20 to 80° C (this is pre-set at 20° C).
- Operation device (setting system):
•3-way valve opening setting (R)
•3-way valve operating light (SV)
When the fluid reaches the temperature set through the regulator, the 3-
way valve diverts the fluid to the radiators and the operating light (SV)
goes on.
When the temperature of the fluid drops below the set value, the system
opens the electrical circuit and the 3-way valve bypasses the fluid directly
to the thermo fireplace.
Attention:
During normal operation check that the warning lights (SV) and (SP) are
lit.
Positioning
The electronic regulator must be installed close to the thermo fireplace.
The sensor of the operation, protection and control devices must be placed
directly on the thermo fireplace or at most on the flow pipe, no more than
5 cm away from the thermo fireplace and in any case before any
intercepting device.
The sensor must be immersed in the well.
Installation
Follow this procedure to install the electronic regulator correctly: loosen
the fastening screw, remove the cover and fasten it in place against the
wall with the dowels supplied.
Then make the connections, paying utmost attention to the wiring diagram
and pass the wires through ducts that are in conformity with the regulations
in force. Put the cover back in place and tighten the screw.
The power supply must be disconnected from the mains and the
AUTO-OFF-MAN selector (S) must be in the OFF position when
all these operations are carried out.
Connect the brown wire (phase) and blue wire (neutral) of the 3-way
Valve, respectively, to terminals 5 and 6 of the regulator.
Connect the yellow/green wire to the earth.
Follow the assembly instructions contained in the
package to connect the regulator to the system properly.
Power Supply (+15 – 10%) Vac 230
Degree of protection IP 40
Min/Max Room Temperature °C 0 to+50
Sensor range m 1,2
Thermometer °C 30 to 90
Maximum contact rating of the circulator W 400
Maximum contact rating of the 3-way valve W 250
Fuse mA 500
fig. M
electronic regulator
Technical Data
IMPORTANT ADVICE REGARDING THE INSTALLATION
The connections, commissioning and verification of proper operation
of the fireplace must be carried out by qualified personnel, who can
implement all connections in accordance with the laws in force,
particularly with Italian Law No. 46/90, apart from complying with
these instructions.
Compliance with regulations regarding the earth
connection is fundamental for the safety of people.
It is obligatory to install a differential circuit breaker switch before
the device and the entire electrical circuit of the thermo fireplace.
It is also obligatory to connect the pump, valve and metal parts of
the thermo fireplace to an earthing system.
ELECTRONIC REGULATOR (KIT 1-2-3-5-6)
LEGEND
AA acoustic alarm switch
Rway valve opening setting (KITS 1-3-5-6)
Rcirculators operation setting (KIT 2)
RIC internal pump setting
SMAN-OFF-AUTO selector
SP pump light
SS overheating light
ST temperature scale
SV 3-way valves light (KITS 1-3-5-6)
SV circulators setting (KIT 2)
The electric control regulator allows you to monitor the operating
conditions and is equipped with:
-
MAN-OFF-AUTO selector (S)
- temperature scale (ST)
- acoustic alarm (AA)
- 3-way valve opening setting (R) (KIT1-3)
- circulators operation setting (R) (KIT2)
- internal pump setting (RIC)
- 3-way valve light (SV) (KIT1-KIT3)
- circulators setting light (SV) (KIT2)
- overheating pump (SS)
- pump light (SP)

ENGLISH
33
Safety pipe Ø> 28mm
Inlet pipe Ø> 18mm
HEAT EXCHANGER FOR SANITARY WATER
(Optional)
This is a very simple and inexpensive device with guaranteed
performance that produces 13-14 litres of hot water per
minute.
It is easily installed on the flow pipe to the radiators, in the most
suitable position according to the layout of the system.
Alternatively, it can be purchased as part of installation
KITS 1/3/6 offered by Italiana CAmini. This has the great
advantage of being removed for maintenance or
replacement without affecting the thermo fireplace.
ELECTRONIC REGULATOR (Optional)
This lets you monitor the operating conditions and is equipped
with:
- MAN-OFF-AUTO selector
- temperature scale
- acoustic alarm
- 3-way valve opening setting
- internal pump setting
- pump light
- 3-way valve light
- overheating light
The electronic regulator and the plate exchanger are
included in the installation KITS
(supplied as optional extras)
hot water from
the fireplace
hot
sanitary
water
cold water from
the mains
Electronic Regulator (220780)
Circulator
UPS 25-50 code 219660
UPS 25-60 code 238270
Valves Kit (421600) consisting of:
automatic air relief valve,
1.5 bar safety valve,
90 ° C thermal relief valve
Flow Switch (220830)
20-plate Heat
Exchanger for sanitary
water (262570)
30-plate Heat
Exchanger for sanitary
water (216620)
1 ” 3-way valve (143330) to set the
water flow to the
system
return water to the
fireplace
Electronic Regulator
(220780)
ACCESSORIES
Exchanger 3-way
code 627780
Roaster
Idro 50-70 cod. 234560
Idro 100 cod. 236710

98
8
38
39
41 42
43
44
45
5
3
7
6
15
14
5
3
4
1
6
2
18
16
19 20
22
21
20 17
24
23 25 26
26
25
33
30
27
36
28 29
34
32
31
35
37
40
48
46
47
46
47
49
51
53
52
50
10
9
60
11
55
54
12
Flangia saldata
alla struttura
62
61
65
64
63
56
56
66
Ritorno
dall’impianto
Ø1” ¼
Ritorno
dall’impianto
Ø1” ¼
Mandata
all’impianto
Ø1” ¼
Mandata
all’impianto
Ø1” ¼
57
19
20
18 16
IDRO 50 - IDRO 50 CS
ante fisse - fixed door leaf - Volet fixe - hoja fija-Feste lügeltür - vast deurtje
OPTIONAL

99
idro50 CS
278910
273090
264210
273320
235640 273100 273110 270390 270400 278180 610190 610200 273150 270420 217450 230610 141660 273160 262420 273170 262430
273180
262410 273190 273630 273200 296110 273210 370270 273230 244480 216793 155540 242420 273240 273260 273250 610220 270410 230040
83060
608850 273270 220780
86460
155170 234550
6630
273280 273290 273300
17650 83590
270420 273310 690610 370260 298740 608890 690033 216660
278910 276280 282520 282530 282540 220910
idro 50
273080
-- -- -- -- -- --
pz.
1 1 1 1 1
1 1
L=0,90 m L=1,10 m
1 1 1 1
L=1,75 m
1
1 1 1 1 2 2 1
1 1 1 1 4 2 2 1 1 1 1
L=3,20 m
1 1 1 1
L=2,30 m
1
1 1 1 1 1 1 1 1 2 2
2 1 1
L=2,00 m
1 1 2 1
2
1
4 1 1 1 1 1 1
NEDERLANDS
Ketelstructuur
Bediening luchtklep Flens voor spit (optioneel vergoeding) Schroef T.E.M. 14x25 Pakking voor flens spit (optioneel vergoeding) Bediening rookklep Rookklep Pakking tussen kap en bovenkant 20x2 Pakking tussen haard en kap 13x8x3
Kap D.18 cm
Steunbeugel stang klep Steunbeugel klep Bovenkant haard
Pakking tussen bovenkant haard D.6
Vuuroppervlak in gietijzer Asla
Asrooster
Stalen vuurplaat rechts Gietijzeren vuurplaat rechts Steun stalen houtwering Steun gietijzeren houtwering Stalen vuurplaat links Gietijzeren vuurplaat links
Houtwering
Houtwering voor gietijzeren vuurplaat
Frontal lijstwerk
Sluitpen deurtje
Sluitveer Plaatje voor deursluiting
Frame deurtje
Pen handvat Veer handvat Veer blokkering deurtje
Pakking D.13
Onderste glashouder
Rechtse glashouder
Linkse glashouder Luchtvang glas Pakking 20 x 1
Glas 497x590x4 Rooster externe luchtinlaat
(optioneel vergoeding)
Mechanisme externe luchtinlaat D.98
(optioneel vergoeding)
Luchtklep
Elektronische regelaar
(optioneel vergoeding)
Elektromotortje spit (optioneel vergoeding) Verlenging spitstaaf (optioneel vergoeding) Spitstaaf
Linkse en rechtse handschoen
Haakpen deurtje Bus afsluiting deurtje Inox plaatje bescherming afsluiting boven Stelschroef afsluiting klep TE M5x16
Rooster voor lucht in beschermkap Pakking frame met structuur D.6 Plaatje scharnier onderste deurtje
Plaatje scharnier bovenste deurtje
Inox plaatje bescherming afsluiting onder
Compleet deurtje (optioneel vergoeding)
Flens sluiting
(optioneel vergoeding)
Glashouder onderste Afstelbare poten
Ketelstructuur met spiraal Afvoerklep thermische veiligheid met put Nippels M3/8 -M1/2"
Kop D.12 Moer 3/8"
Koperen verloopstuk van F1/2" naar M3/4"
DEUTSCH
Heizkesselkörper Luftklappenbetätigung Bratspießflansch (optional zu Bezahlen) Sechskantkopf-Schraube M14x25
Dichtung für Bratspießflansch (optional zu Bezahlen)
Rauchklappensteuerung
Rauchklappe Dichtung 20x2 zwischen Rauchfang und Gewölbe Dichtung zwischen Kamin und Rauchfang 13x8x3
Rauchfang D. 18 cm Halterungsbügel Klappenstange Halterungsbügel Klappe
Kamingewölbe Dichtung zwischen Gewölbe und Kamin D. 6 Brennraumboden aus Gusseisen Aschenbehälter
Aschenrost Rechter Brennraumboden aus Blech Rechter Brennraumboden aus Gusseisen Blechhalterung Brennholzschutzleiste
Halterung Brennholzschutzleiste aus Gusseisen Linker Brennraumboden aus Blech Linker Brennraumboden aus Gusseisen Brennholzschutzleiste
Brennholzschutzleiste für Brennraumboden aus Gusseisen
Vorderer Rahmen Türverschlussstift Verschlussfeder
Plättchen für Flügelverschluss Türrahmen Gabelzapfen für Griff
Grifffeder Feststellfeder Tür Arktik-Dichtung D. 13 Untere Scheibenhalterung
Rechte Scheibenhalterung Linke Scheibenhalterung Luftableitblech für Scheibe Dichtung 20 x1
Scheibe 497x590x4 Gitter für Außenlufteinlass (optional zu Bezahlen) Außenlufteinlassmechanismus D. 98 (optional zu Bezahlen) Luftklappe
Elektronischer Regler (optional zu Bezahlen)
Elektromotor Bratspieß
(optional zu Bezahlen)
Bratspießverlängerung
(optional zu Bezahlen)
Bratspieß
Beidhändiger Handschuh
Stift für Türaufhängung Türenverschlussbuchse Edelstahl-Schutzplättchen für oberen Verschluss
Sechskantkopf-Einstellschraube M5x16 für Klappenverschluss
Luftgitter Innenluft Rauchfangabdeckung
Dichtung zwischen Rahmen und Ofenkörper D. 6 Unteres Scharnierplättchen Oberes Scharnierplättchen
Edelstahl-Schutzplättchen für unteren Verschluss Kompletter Türflügel
(optional zu Bezahlen)
Verschlussflansch(optional zu Bezahlen)
ObereGlashalteleisten Verstellbare Füße
Ofenkörper mit Rohrschlange Überhitzungsschutzventil mit Schacht Nippel M3/8 -M1/2" Einsatz D.12
Mutter 3/8"
Reduzierstück Innengew. 1/2" zu Außengew. 3/4", Messing
ESPAÑOL
Estructura de la caldera
Mando compuerta aire Brida para rustidor
(compra a opcional)
Tornillo T. E. M 14x25 Junta para brida rustidor
(compra a opcional)
Mando compuerta de humos Compuerta de humos Junta entre campana y bóveda 20x2
Junta entre chimenea y campana 1 3x8x3
Campana D.18 cm
Abrazadera de sujeción varilla compuerta Abrazadera de soporte compuerta
Bóveda chimenea Junta entre bóveda chimenea D.6
Plano del fuego en hierro fundido
Cubeta cenizas Parrilla cenizas
Plano del fuego dcho. de chapa Plano de fuego dcho. en hierro fundido
Soporte barra paraleña en chapa Soporte barra paraleña en hierro fundi Plano del fuego izqdo. en chapa
Plano del fuego izqdo. en hierro fundido Bara paraleña
Barra paraleña para plano fuego en hierr
Marco frontal
Perno para cierre puerta
Muelle para el cierre Placa de cierre de la puerta
Bastidor puerta pequeña
Perno manija
Muelle manija Muelle bloqueo puerta pequeña
Junta D.13 artica
Sujeta vidrio inferior
Sujeta vidrio derecho
Sujeta vidrio izquierdo Transportador aire vidrio
Empaquetadura 20 x 1
Vidrio 497x590x4 Rejilla toma aire externa (compra a opcional)
Mecanismo toma de aire externo D.98 (compra a opcional)
Compuerta de aire
Regulador electrónico (compra a opcional)
Motor electrónico rustidor
(compra a opcional)
Extensión varilla rustidor
(compra a opcional)
Varilla espetón
Guante ambidiestro
Perno enganche puerta pequeña
Casquillo cierre puerta pequeña Placa inox protección cierre superior Tornillos regulación cierre compuerta TE M5
Rejilla de aire interna controcampana Junta bastiidor con estructura D.6
Placa bisagra puerta pequeña inferior Placa bisagra puerta pequeña superior
Placa inox protección cierre inferior Grupo puerta pequeña
(compra a opcional)
Brida de cierre (compra a opcional)
Sujeta vidrios superior
Pies regulables Estructura de la caldera con serpentina
Válvula de descarga de seguridad térmica con pozo.
Niples M3/8 -M1/2" Ogiva D.12 Tuerca 3/8" Reducción de F1/2" a M3/4" cobre
FRANÇAIS
Structure chaudière
Commande trappe air
Bride pour tournebroche
(optional à paier)
Vis T.E.M. 14x25
Garniture pour bride tournebroche
(optional à paier)
Commande trappe fumées Trappe fumées Garniture entre hotte et voute 20x2 Garniture entre cheminée et hotte 13x8x3
Hotte D.18 cm
Étrier de soutien tige trappe Étrier de support trappe Voute cheminée
Garniture entre voute cheminée D.6
Plan feu en fonte Tiroir cendre
Grille cendres
Plan feu droit en tôle
Plan feu droit en fonte Support barre pare-bois en tôle
Support barre pare-bois en fonte
Plan feu gauche en tôle
Plan feu gauche en fonte
Barre pare-bois
Barre pare-bois pour plan feu en fonte
Cadre frontal
Pivot pour fermeture volet
Ressort pour fermeture
Plaque de fermeture porte
Châssis petit volet
Pivot poignée Ressort poignée Ressort blocage porte
Garniture D.13 artica
Dispositif inférieur de fermeture de la vitre
Dispositif droit de fermeture de la vitre
Dispositif gauche de fermeture de la vitre Convoyeur air vitre Garniture 20 x 1 Vitre
497x590x4
Grille prise d’air externe
(optional à paier)
Mécanisme prise d'air externe D.98
(optional à paier)
Trappe air
Régulateur électronique
(optional à paier)
Moteur électrique tournebroche
(optional à paier)
Rallonge tige tournebroche
(optional à paier)
Tige broche
Gant ambidextre
Pivot accrochage petit volet Douille fermeture petit volet Plaque inox protection fermeture supérieure Vis réglage fermeture trappe TE M5x16
Grille air interne contre-chape
Garniture châssis avec structure D.6
Plaque charnière porte inférieure
Plaque charnière porte supérieure
Plaque inox protection fermeture inférieure Ensemble petit volet
(optional à paier)
Bride de fermeture
(optional à paier)
Pare-closes supèrieur
Pieds réglables
Structure chaudière avec serpentin Soupape décharge sécurité thermique avec logem. Niples M3/8 -M1/2" Ogive D.12 Ecrou 3/8"
Réduction de F1/2" à M3/4" laiton
ENGLISH
Bolier structure Air damper control
Flange for roaster
(optional to pay)
T.E.M screw 14x25
Flange seal for roaster
(optional to pay)
Smoke damper control Smoke damper
Seal between the cowl and the vaulted top part 20x2
Gasket between the fireplace and the cowl 13x8x3
Cowl D.18 cm Damper rod support bracket Damper support bracket
Fireplace vaulted top part Seal between the fireplace vaulted top part D.6
Hearth made of cast iron
Ash pan Ash grill Right part of hearth base made of sheet metal
Right part of hearth base made of cast iron
Wood guard support rod made of sheet metal
Wood guard support rod made of cast iron
Left part of hearth base made of sheet metal
Left part of hearth base made of cast iron
Wood guard rod
Wood guard rod hearth base made of cast iron
Front frame Pin to close the door leaf Closing spring Plate to close the door leaf
Door frame Handle pin
Handle spring
Door blocking spring
Artic seal D. 13 Lower glass holder Right glass holder Left glass holder Air conveyor of the glass
Gasket 20 x 1 Glass
497x590x4
External air inlet grille
(optional to pay)
External air inlet mechanism D.98
(optional to pay)
Air damper Electronic regulator
(optional to pay)
Roaster electric motor
(optional to pay)
Roaster rod extension
(optional to pay)
Spit rod
(optional to pay)
Interchangeable left/right glove Door hooking pin
Door bush lock Stainless steel upper lock protection plate Damper lock adjustment screw TE M5x16 Fireplace mantel internal air grille
Frame gasket with structure D.6 Lower door hinge plate Upper door hinge plate Stainless steel lower lock protection plate
Door assembly
(optional to pay)
Closing flange
Holder glass holders
Adjustable feet
(optional to pay)
Boiler structure with coil Safety thermal relief valve with well
Nipples M3/8 - M1/2" Ogive D.12
Nut 3/8" Brass reducer from F1/2" to M3/4"
ITALIANO
Struttura caldaia
Comando serranda aria
Flangia per girrarosto (optional a pagamento)
Vite T.E.M 14x25
Guarnizione flangia girrarosto (optional a pagamento)
Comando serranda fumi Serranda fumi
Guarnizione tra cappa e volta 20x2
Guarnizione tra camino e cappa 13x8x3
Cappa D. 18 cm
Staffa sostegno asta serranda Staffa supporto serranda
Volta camino
Guarnizione tra volta camino D.6
Piano fuoco in ghisa
Vaschetta cenere
Griglia cenere
Piano fuoco dx in lamiera Piano fuoco dx in ghisa
Supporto barra para legna in lamiera
Supporto barra para legna in ghisa
Piano fuoco sx in lamiera
Piano fuoco sx in ghisa
Barra para legna Barra para legna per piano fuoco in ghisa
Cornice frontale
Perno per chiusura anta
Molla per chiusura
Piastrina di chiusura anta Telaio antina
Perno maniglia
Molla maniglia
Molla bloccaggio antina
Guarnizione D.13 artica
Fermavetro inferiore Fermavetro destro Fermavetro sinistro
Convogliatore aria vetro
Guarnizione 20x1
Vetro 497x590x4
Griglia presa aria esterna (optional a pagamento)
Meccanismo presa aria esterna D.98 (ptional a pagamento)
Serranda aria Regolatore elettronico (optional a pagamento) Motorino elettrico girrarosto (optional a pagamento)
Prolunga asta girrarosto (optional a pagamento)
Asta spiedo (optional a pagamento) Guanto ambidestro Perno aggancio antina
Bussola chiusura antina Piastrina inox protezione chiusura superiore Vite regolazione chiusura serranda TE M5x16
Griglia aria interna controcappa Guarnizione telaio con struttura D.6
Piastrina cerniera antina inferiore
Piastrina cerniera antina superiore
Piastrina inox protezione chiusura inferiore Assieme antina (optional a pagamento) Flangia di chiusura
Fermavetro superiore Piedi regolabili (optional a pagamento)
Struttura caldaia con serpentina Valvola scarico sicurezza termica con pozz.
Niples M3/8 -M1/2” Ogiva D.12 Dado 3/8” Riduzione da F1/2” a M3/4” ottone
1 2
3
4 5 6 7
8
9
10 11 12
14 15
16
17
18 19 19 20 20
21
21 22
22
23
24 25 26 27
28
29 30 31 32
33
34 35 36 37 38
39
40
41
42 43 44
45
46 47 48 49
50 51 52 53
54 55 56 57
60
61 62 63 64 65 66

100
40
43
42
45
46
47
60
5
3
7
6
13
15
14
32
27
29
29
37 38 38
37
33
31
34
30
30
32
31
39
28
33
25
26
26
25
36
35
39
36
48
5
3
4
1
18
6
2
16
19
20
22
21
20
17
23
24
8
51
57
49
50
49
50
52
54
53
55
56
56
55
10
9
11
59
58
41
12
61
61
Ritorno
dall’impianto
Ø1”¼
Ritorno
dall’impianto
Ø1” ¼
Mandata
all’impianto
Ø1”¼
Mandata
all’impianto
Ø1” ¼
44
44
20
19
18
OPTIONAL
IDRO 70
ante fisse - fixed door leafs - Volet fixes - hoja fijas - Feste lügeltüren - vast deurtjes