Edimax EW-7416APn User manual

0

1
M
Mu ul lt ti i- -L La an ng gu ua ag ge e Q QI IG G o on n t th he e C CD D
=
== == == == == == == == == == == == == == == == == == == == == == == == == == == == == == =
Č
Če es sk ký ý: Českého průvodce rychlou instalací
naleznete na přiloženém CD s ovladači
D
De eu ut ts sc ch h: : Finden Sie bitte das deutsche S.A.L.
beiliegend in der Treiber CD
E
Es sp pa añ ño ol l: Incluido en el CD el G.R.I. en Español.
F
Fr ra an nç ça ai is s: :Veuillez trouver l’français G.I.R ci-joint
dans le CD
I
It ta al li ia an no o: : Incluso nel CD il Q.I.G. in Italiano.
M
Ma ag gy ya ar r: :
A magyar telepítési útmutató
megtalálható a mellékelt CD-n
N
Ne ed de er rl la an nd ds s: De nederlandse Q.I.G. treft u aan op
de bijgesloten CD
P
Po ol ls sk ki i: Skrócona instrukcja instalacji w języku
polskim znajduje sięna załączonej płycie CD
P
Po or rt tu ug gu uê ês s: Incluído no CD o G.I.R. em Portugues
Р
Ру ус сс ск ки ий й: : Найдите Q.I.G. на pусскoмязыке на
приложеном CD
T
Tü ür rk kç çe e: :Ürün ile beraber gelen CD içinde Türkçe
HızlıKurulum Kılavuzu'nu bulabilirsiniz

2
Copyright©by Edimax Technology Co, LTD. all rights reserved. No
part of this publication may be reproduced, transmitted, transcribed,
stored in a retrieval system, or translated into any language or
computer language, in any form or by any means, electronic,
mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of this company
This company makes no representations or warranties, either
expressed or implied, with respect to the contents hereof and
specifically disclaims any warranties, merchantability or fitness for any
particular purpose. Any software described in this manual is sold or
licensed "as is". Should the programs prove defective following their
purchase, the buyer (and not this company, its distributor, or its dealer)
assumes the entire cost of all necessary servicing, repair, and any
incidental or consequential damages resulting from any defect in the
software. Further, this company reserves the right to revise this
publication and to make changes from time to time in the contents
hereof without obligation to notify any person of such revision or
changes.
All brand and product names mentioned in this manual are trademarks
and/or registered trademarks of their respective holders.
Linux Open Source Code
Certain Edimax products include software code developed by third
parties, including software code subject to the GNU General Public
License ("GPL") or GNU Lesser General Public License ("LGPL").
Please see the GNU (www.gnu.org) and LPGL (www.gnu.org)
Web sites to view the terms of each license.
The GPL Code and LGPL Code used in Edimax products are
distributed without any warranty and are subject to the copyrights
of their authors. For details, see the GPL Code and LGPL Code
licenses. You can download the firmware-files at
http://www.edimax.com.tw under "Download" page.

3
English Version.
G
Ge et tt ti in ng g S St ta ar rt te ed d
Before deploying the Access Point, please make sure all the PCs
in your wired network are able to obtain an IP address
automatically from the router like the figure below.
After the Access Point is deployed, you can surf the Internet /
Intranet wirelessly as show in the figure below.

4
P
Ph hy ys si ic ca al l D De es sc cr ri ip pt ti io on n
Front Panel
The LED lights located on the Access Point’s front panel provide
information of the Access Point’s current status. EW-7416APn
LED Color Status Description
Lit Power is supplied.
PWR
(Power) Green
Off No Power.
Flash Antenna is transmitting or
receiving data.
WLAN
(Wireless LAN)
Green
Orange
(EW-7209APg) Off Antenna is not transmitting
or receiving data.
On A valid link is established.
Flash It is transmitting or receiving
data.
LAN
(Link / Act) Green
Off No link is established.
Back Panel
EW-7416APn
zAntenna Connector

5
This is where you connect the antenna. It is a round connector
(standard Reverse SMA).
z12 VDC
This is where you connect the power adapter.
zWPS/Reset
Reset the router to factory default settings (clear all settings) or
start WPS function. Press this button and hold for 20 seconds
to clear all settings, and press this button for less than 5
seconds to start WPS function.
z10/100M (EW-7416APn )
This LAN port is where you connect the Access Point to your
Ethernet devices (switch or router).
W
Wi ir re el le es ss s L LA AN N A Ac cc ce es ss s P Po oi in nt t C Co on nf fi ig gu ur ra at ti io on n
To configure the other advanced settings of this Access Point with
advanced setting such as data encryption, please follow the
procedures to login the Access Point’s setup page.
To configure the more advanced settings from this Access Point,
such as data-encryption, please follow the procedure to login the
Access Point’s setup page.
The IP address of the Access Point is 192.168.2.1
First, assign an IP Address to the PC
Before assigning an IP address to the PC, please connect a
network cable from the LAN port of the PC to the LAN port of the
Access Point as show below.

6
1. Click “Start” on the task bar then select the “Control Panel” to
open it.

7
2. Click “Switch to Classic View” on the top left corner to see
more setting icons…
3. Find the “Network Connection” icon then Double-Click to
open the network connection settings.

8
4. You will see the “Local Area Connection” icon, click the icon
to highlight it, then Right-Click the mouse to open the sub-menu
and select the “Properties” to setup the IP address.
zClick and highlight the “Internet Protocol (TCP/IP)”, then click
the “Properties”

9
zSelect “Use the following IP address”. Enter a fixed IP
address, for example “192.168.2.10”, with a subnet mask of
“255.255.255.0” and leave “Default gateway”, “Preferred
DNS server” and “Alternate DNS server” blank then press
“OK” to close.
Second, login to the Access Point with a Web Browser
1. Open up web browser and type in 192.168.2.1 (Access Point
default IP address) to access the Access Point’s setup page.
2. A screen requesting user name and password, shown on next
page, will appear. The default user name and password are:
User Name: admin / Password: 1234
Note: It’s highly recommended to change the login settings and
keep it for future reference.