EFG EFG IZI Pro User manual

EFG IZI Pro
Assembly Instruction 039167
For more information,
please visit www.efg.info
170308 / Produced by: EFG Marketing Support

Step 1 - Assembly beams and legs.
Recommended beam length for following table top length (2-column):
1600 = Beam length 1314 mm (Top extension on table according to page 5)
1800 = Beam length 1514 mm (Top extension on table according to page 5)
M8x25
Leave one of these screws
unmounted in the crossbar
for connection third column.
For 3-Columns go to page 3.
Wiggle the leg when
mounting the crossbars.
It makes it easier to
mount the screws.
M8x25 (x7)
(8pcs for single stand)
x22 (optional)
(12pcs for single stand)
Setscrew at this side
M8x16 (x4) - Side Bars.
M8x16 (x6) - Feet (4pcs for single stand)
Ø16 (x36) - Covers For Screw/Sidebars (Black/Gray/White)
EFG IZI Pro - 2
Step 2 - Assembly Feet and Side Bars.

Step 3 - Assembly 3-column 90°.
Step 4 - Mount frame to table top - 2-column.
Recommended beam length for following table top length (2-column):
1600 = Beam length 1314 mm (Top extension on table according to page 5)
1800 = Beam length 1514 mm (Top extension on table according to page 5)
M8x35 (x1) - Use for connection 3-Legs 90°
M8x16 (x6) - Feet & crossbar corner
M8x25 (x6) - Cross bar and
. connection 90°
Ø5,0x60 (x8) - Screw Beams
. (4pcs Single stand)
Ø4,5x20 (x8) - Screw Sidebars
Loosen setscrews in crossbars and
adjust stand width symmetric to wished position. EFG IZI Pro - 3
OBSERVE
M8x16 (x2)
Round socket
M8x16 (x2) - Side bars
Cover for screw M8 (x16) - Side bars
OBSERVE
Use M8x35 to mount the
connection in crossbar.
M8x16 Countersunk
M8x25 Countersunk

Step 5 - Mount frame to table top - 3-column.
Step 6 - Cable fastening.
Loosen setscrews in crossbars and adjust stand width symmetric to wished position.
Ø5,0x60 (x8) - Screw beams
Ø4,5x20 (x8) - Screw Sidebars
Structure excess cabling under the table top, use a cableclip to fasten powersupply.
EFG IZI Pro - 4
Ø3,5x16 (x2) - Handset
2-COLUMN
Ø3,5x16 (x2) - Handset
3-COLUMN

Step 7 - Observe.
INFO - Accessories (Gables) + Reset.
ACCESSORIES (GABLES):
Below you can see recommended distance to
table top edge on gables for enabling other
acessories to be added.
EFG IZI Pro - 5
Observe: Make sure every screw is tightened
before use. Be careful not to tighten them too
hard, this will damage the chipboard and the
legs will not be fastened in a proper way.
Turn the table around to standing position and
plug the cable.
Ready to use!
120 mm
SUITED ACESSORIES:
- TAB Screens (Ex: A29F01)
- ADD Stack (Ex: ADDSTACKK)
- Butler (Ex: ADDBUTLK)
- ScreenIT Standard (Ex: A30B81)
RESET:
Below you will nd the guide for reseting the
desk if necessary.

The product contains one or more of following materials:
Metal, plastic, wood, fabric, foam.
100kg
For more information,
please visit www.efg.info 170308/ Produced by: EFG Marketing Support
Försäkran om överensstämmelse för maskiner/ Declaration of conformity
SE - EFG IZI Pro överensstämmer med Maskindirektivet AFS 2008:3 och AFS 2009:5,
European directive 2006/42/EG, EMC-direktiv 2004/108/EG och LVD 2014/35/EU.
UK - EFG IZI Pro complies with the European directive 2006/42/EG, EMC-directive
2004/108/EG and LVD 2014/35/EU.
DK - EFG IZI Pro er i overensstemmelse med European directive 2006/42/EG,
EMC-directive 2004/108/EG og LVD 2014/35/EU.