EFG SURSS720 User manual

EFG Surround
Assembly instructions
www.efg.info
150310 / Art no. 039112. Produced by: EFG, Market support.
The product contains following material: Wood, metal, plastic, padding foam and fabric.
100kg

EFG Surround - Overview (Way of assembling the pods)
All the standard pods with recommended assembly start (Marked with S). Texts shows the right amount of feets and
their positioning on seperate screen. Right and left is marked after viewing the screens from inside the pod.
SURSS720
SURSS720R
SURSS1050
SURSS1050R
SURSS460
SURSS460R
S
3 Feet
0 Feet
3 Feet
SURLS460
SURLS460R
S
3 Feet
1 Foot (center)
3 Feet
SURMEETL
S
3 Feet
3 Feet
1 Foot (right)
2 Feet
(on widest
part of
screen)
1 Foot (center)
2 Feet
(on widest part of screen)
1 Foot (left)
SURMEETSB1
SURMEETSB1R
S
3 Feet 1 Foot (center)
3 Feet
0 Feet
3 Feet
3 Feet
1 Foot (center)
SURSL720
SURSL1050
SURSR720
SURSR1050
2 Feet
(on widest
part of screen)
3 Feet
0 Feet
S
3 Feet S
3 Feet
0 Feet 3 Feet
2 Feet
(on widest
part of screen)
SURB1000 SURB1200
SURB1400 SURB1600
SURB1800 SURB2000
2 Feet
(on widest
part of screen)
2 Feet
(on widest
part of screen)
2 Feet S
2 Feet
(on widest
part of screen) 2 Feet
(on widest
part of screen)
S
2 Feet
S
3 Feet
1 Foot (center)
3 Feet
S
3 Feet
1 Foot (center)
3 Feet
S
3 Feet
3 Feet
1 Foot (center)
1 Foot (center)
S
3 Feet
1 Foot (right)
1 Foot (right)
2 Feet
(on widest part of screen)

EFG Surround - General assembly
Detailed instructions for the different stages during the assembly and suggestion of order.
Letters marked after each text shows the matched illustration.
Pods with table tops (+roof):
1= Start with assemble the feets (A).
2= Assemble the screens (B).
3= Assemble the brackets (C).
4= Assemble table tops (C).
(5= Assemble the roof) (D).
Pods with sofa and table tops (+roof):
1= Start with assemble the feets (A).
2= Assemble the screens (B).
3= Assemble the brackets and beam (E).
4= Assemble electronics/lamp to the table top (G).
5= Assemble table top to the box (G).
6= Assemble box to the base (G).
7= Place the base inside the pod (H).
(8= Assemble the roof) (D).
For article SURLSOFB2: Replace steps 4-6 with (F & I).
For article SURLSOFB1: Skip steps 4-6.
A = Assemble the feets
Be aware of not tighten feet
too much. Stop when feet
are in contact with fabric.
B = Assemble the screens
C = Assemble the table top brackets D = Assemble the roof
Note:
Use a rubber hammer gently on screens with male hooks if
they are a bit tight.
For easier guidance place your foot under the screens at
the bottom.
Screen
Connector
Roof
x2
x2
Screws:
2x FXTB 4x20 (Table Tops)
2x MF6S M8x35 Countersunk (Screens)
E = Assemble the sofa brackets and beams F = Assemble the cords.
G = Assemble the sofa parts
x2
x2
Table top
(Assemble electronics/
lamp before these steps)
Box
Base
Top illustration:
4x MK6S M8x40 (Box - Base)
Left illustration:
4x MK6S M6x25 (Table Top - Box)
Bracket
Table top
Screen
Foot
Screen Screen
(Male hook)
Screen
Bracket
Beam
Note:
Positioned as illustrated with beam on top.
Both illustrations use 2x MF6S M8x35 countersunk on each
bracket/beam gable.
Beam
Base
Cable clamp
(x2)
Table Top
(ex: A50B34)
Note:
Each cable clamp uses 1x FXTB 4x20.
Before lifting in the base, lay the cord
inside the track. Position the cable clamps
according to the illustration on each side of
where the beam will be positioned.
An extra track is found in the middle at the
back of the base.
Track
Note: Parts illustrated upside down.

H = Placing the base inside the pod
Note:
Use the handle holes for easier lifting. While lifting aim the smaller
slots at the back of the base towards the brackets on the screens.
Bracket
Bracket
Step 2:
Place the base upside down and insert the table top inside
the cut-out with cord outlet upwards, towards base bottom
edge.
Step 3:
Mount M6-screws and screw heads as illustrated to the
brackets. Fixate the table top and make sure it´s in level
with the base.
Cord outlet
Step 4:
Plug in the power cord and lift in the base according to illustration H.
Note:
For easier access to place the cord in the track: perform illustration F
before these steps.
I = Assemble the Table Top-electronics mounting kit (ex: A50B34)
Step 1:
Mount the two brackets according to illustration with the
flange pointed towards the bottom. Replace screws with the
new, longer ones.
Bracket
New screws Bracket
Bracket
Screens
Beam
Base
Box
Table top
Bracket
Power cord
Screw head
Screw
Slot
Handle holes

EFG Surround - Overview (Sizes and names of screens)
All the standard pods with marked sizes of the straight screens and the names of other screens.
Article number are followed by the drawing number (subarticle) of the assembled pods.
To access the individual screens: Search in Vault using the drawing number, for example: 629013.
SURSS720 - 629000
SURSS720R - 629001
SURSS1050 - 629002
SURSS1050R - 629003
SURSS460 - 629004
SURSS460R - 629005
R235 - Left
400
R235 - Right
SURLS460 - 629010
SURLS460R - 629011
SURMEETL - 629012
800
R235 -
Left
1200
800
SURMEETSB1 - 629013
SURMEETSB1R - 629014
1200
600
1200
SURSL720 - 629006
SURSL1050 - 629008
SURSR720 - 629007
SURSR1050 - 629009
120° - Left
120° -
Right
SURB1000 - 629015 SURB1200 - 629016
SURB1400 - 629017 SURB1600 - 629018
SURB1800 - 629019 SURB2000 - 629020
90° - Left
R235 - Right
R235 - Left
R235 - Right
R235 - Left
1200
R235 - Right
R235 - Left
R235 - Right
R235 - Right
R235 - Left
R235 - Left 400
120° -
Right
120° - Left
400 R235 - Right
600
90° - Right
800
90° - Right
90° - Left
90° - Left
1000
90° - Right
90° - Left
1200
90° - Right
700
700
90° - Left
90° - Right
800
800
90° - Left
90° - Right