ekwb EK-Classic GPU Water Block RTX 3080/3090... User manual

INSTALLATION MANUAL
GPU WATER BLOCK
EK-Classic GPU Water Block
GeForce RTX 3080/3090 D-RGB

Before you start using this product, please follow these basic guidelines:
Carefully read the manual before beginning with the
installation process.
Remove your graphics card from the computer for the safest
mounting process to prevent any possible damage to your
GPU or its circuit board (PCB).
EK Fittings require only a small amount of force to screw
them firmly in place since the liquid seal is ensured with the
rubber O-ring gaskets.
The use of quality market-proven corrosion-inhibiting
coolants is always strongly recommended for any liquid
cooling system.
Do not use pure distilled water as a cooling liquid! For best
results, EK recommends the use of EK-CryoFuel Coolants.
Make sure to bleed air out of your water block thoroughly in
order to reach optimal performance.

- 3 -
TABLE OF CONTENTS
BOX CONTENTS 4
WATER BLOCK DIMENSIONS 5
WATER BLOCK SPECIFICATIONS AND MAIN PARTS 6
PREPARING THE GRAPHICS CARD 7
REMOVING THE STOCK COOLER 7
CLEANING THE PCB 7
CUTTING AND PLACING THERMAL PADS 8
APPLYING THERMAL COMPOUND 9
INSTALLING THE WATER BLOCK 9
PLACING THE BLOCK ON THE GRAPHICS CARD 9
ATTACHING THE BLOCK TO THE GRAPHICS CARD 10
CHECKING FOR CONTACT 10
INSERTING THE GRAPHICS CARD INTO THE CHASSIS 11
INSTALLATION OF FITTINGS AND TUBING 11
CONNECTING THE D-RGB LED STRIP 12
TESTING THE LOOP 12
SUPPORT AND SERVICE 13
SOCIAL MEDIA 13

- 4 -
BOX CONTENTS
4 mm
4 mm
6 mm
8 mm
M3x4 DIN7985 Screw (2 pcs) EK-Loop Multi Allen Key (1 pc)
M2.5 Nut (2 pcs)
M2.5x6 AX1 Screw (13 pcs)
Allen Key 2.5 mm (1 pc)
Thermal Pad F 1.0 mm (4 pcs)
Thermal Grease (1 pc)
M2.5x8 AX1 Screw (2 pcs)
M2.5x4 AX1 Screw (16 pcs)
EK-Classic GPU WB GeForce RTX 3080/3090 D-RGB PVC Washer M2.5 (16 pcs)
120 mm
16 mm
EK-Plug G1/4 (2 pcs)
Universal Mounting Mechanism – You may not need every
screw from this package.

- 5 -
WATER BLOCK DIMENSIONS
91.70 mm
120.70 mm
211.60 mm
113.26 mm
124.76 mm
20.60 mm

- 6 -
WATER BLOCK SPECIFICATIONS AND MAIN PARTS
Technical Specification:
- Dimensions: (LxHxW) – 211.6 x 124.8 x 20.6 mm
- D-RGB (Adressable RGB) cable length: 500 mm
- D-RGB LED COUNT: 10
- D-RGB connector standard 3-pin (+5V, Data, Blocked, Ground
EK BADGE
O-RING 125 x 2
JE T PL ATE
TOP PROFILE
(ALU)
COLDPLATE
(COPPER/NICKEL)
TOP PLATE
(PLEXI/ACETAL) LED D-RGB STRIP
M4x8 DIN7984 SCREW
TERMINAL (ACETAL)
M4x27 DIN7984
SCREW
M3,5/M2,5x2,5 STANDOFF-SHORT
O-RING 15x1
COLDPLATE INSERT (PLEXI)
M3.5/M2.5 x 12.6
STANDOFF-LONG

- 7 -
PREPARING THE GRAPHICS CARD
STEP 1
REMOVING THE STOCK COOLER
Place your graphics card on the flat surface and carefully remove the
stock cooler. Do not forget to unplug all the LED and fan connectors.
Pay attention to the following steps in order to install the EK-Classic
GPU WB GeForce RTX 3080/3090 D-RGB water block on the
graphics card.
STEP 2
CLEANING THE PCB
Carefully detach the original stock cooler after removing all screws
that are securing it to the board. Wipe off the remains of the original
thermal compound using a nonabrasive cloth or Q-tip, as shown
in the sample image, until the components and circuit board are
completely clean. EK recommends the use of denatured alcohol for
removing TIM leftovers.
STEP 2

- 8 -
STEP 1
Your GPU water block comes with thermal pads that have to be cut
into smaller pieces to cover all the VRM components, such as COILs,
MOSFETs, and drivers.
You must remove the protective foil from both sides of the
thermal pad before installation.
Replacement thermal pads:
4x Thermal Pad F 1.0 mm – (120 x 16 mm) EAN: 3830046996732
Thermal Pad F – 1.0 mm (120 x 16 mm)
CUTTING AND PLACING THERMAL PADS
120 mm
16 mm
1 mm
STEP 2
Once cut to size, thermal pads should be placed on the PCB, as
illustrated below. EK made sure to provide you with more than an
adequate quantity of thermal pads to complete this Step.
Thermal Pad F 1.0mm
STEP 1
STEP 2
RTX™ 3080/3090

- 9 -
Thermal Grease
STEP 1
Apply the enclosed EK-TIM Ectotherm thermal grease (thermal
compound) on the CPU heat spreader – IHS – as shown in the
image. The layer of the thermal compound must be thin and even
over the entire surface of the IHS.
The excessive or uneven application of thermal grease
may lead to poor performance!
APPLYING THERMAL COMPOUND
For this Step, you will need:
INSTALLING THE WATER BLOCK
STEP 1
PLACING THE BLOCK ON THE GRAPHICS CARD
This procedure is the same for all full-cover water blocks.
Carefully position the water block with preinstalled standoffs on
the graphics card. During this process, make sure you have aligned
mounting holes of the PCB with holes of the water block (the same
applies to other tops).
Pay attention not to use too much force when pressing
the block down to the PCB since chip dies are prone
to cracking.
STEP 1
STEP 1

- 10 -
For this Step, you will need:
M 2.5 PVC Washer
(12 pcs)
M2.5 x 4 AX1
(12 pcs)
Phillips Head
Screwdriver
4 mm
M2.5 x 4 AX1 SCREW
M2.5 PVC WASHER
STEP 2
ATTACHING THE BLOCK TO THE GRAPHICS CARD
Use twelve (12) M2.5 X 4 AX1 screws and M2.5 PVC washers.
Tighten the screws evenly using the Phillips head screwdriver.
EK recommends you start tightening the screws around the GPU
core first and then continuing outward to prevent damage to the
GPU. Always use a plastic washer under each screw!
CHECKING FOR CONTACT
If necessary, temporarily remove the water block to check for uniform
surface contact between the block and components. Pay special
attention to the VRM section of the graphics card. Check whether
the water block makes contact with the intended integrated circuit.
Then repeat Steps from the previous section to re-attach the block.
In case you fail to obtain good contact, please check
again or contact our support service at
https://www.ekwb.com/customer-support/.
STEP 2