ekwb EK-Quantum Velocity 2 User manual

USER GUIDE
EK-Quantum
Velocity² - AM5 Backplate

Please note the installation of the product is intended to be undertaken
by an adequately trained and experienced person. You are installing the
product at your own risk. If you are not properly trained or experienced or
feel unsure about the installation procedure, please refrain from installing
the product yourself and contact our tech support for assistance. We
disclaim our liability for any damages to the product as well as incidental,
consequential, or indirect damages incurred due to improper or
inappropriate installation.
Before you start using this product, please follow these basic guidelines:
Please carefully read the manual before beginning the
installation process.
The EK Fittings require only a small amount of force to screw
them firmly in place since the liquid seal is ensured by the
rubber O-ring gaskets.
The use of corrosion inhibiting coolants is always recommended
for liquid cooling systems, and mandatory for nickel-plated
water blocks.
Do not use pure distilled water! For best results, EK recommends
the use of EK-Cryo Fuel coolants.
Make sure to thoroughly bleed air out of your water block, or
you will not reach optimal performance.

- 3 -
TABLE OF CONTENTS
BOX CONTENTS 4
BACKPLATE DIMENSIONS 5
PREPARING THE AM4 WATER BLOCK FOR UPGRADE 6
PREPARING THE AM5 MOTHERBOARD 7
INSTALLING THE WATER BLOCK 9
CONNECTING THE D-RGB LED STRIP 11
TESTING THE LOOP 11
WARRANTY 12
SUPPORT AND SERVICE 13
SOCIAL MEDIA 13

- 4 -
BOX CONTENTS
AM5 Backplate
Allen Key 2.5 mm (1 pc) TX20 L-Shaped Wrench (1 pc)
Thermal grease (1 pc)

- 5 -
BACKPLATE DIMENSIONS
90 mm 60 mm
43 mm
53 mm
8.9 mm
7.6 mm
6.3 mm

- 6 -
STEP 1
TOP OF THE
MOTHERBOARD
PREPARING THE AM4 WATER BLOCK FOR UPGRADE
Important! Before starting, make sure to have a clean, flat
surface to work on. It is recommended to put foam or soft
material to lay a motherboard on.
STEP 1
If the EK-Quantum Velocity2 AM4 water block is already installed,
remove the backplate from the motherboard’s backside using Allen
Key 2.5 mm (As shown in the picture).
STEP 2
Detach the water block from the motherboard and save it for later
steps. Clean the CPU cold plate using a non-abrasive cloth or Q-tip.
STEP 2

- 7 -
STEP 1
Using a Philips-head screwdriver remove the four screws securing
the original plastic hold-down clamps around the socket as shown in
the illustration. Remove the hold-down clamps and store them away.
PREPARING THE AM5 MOTHERBOARD
UNC 6-32 SCREW
HOLD-DOWN
CLAMPS
STEP 1
STEP 2
After removing the plastic hold-downs, additional four (4) Screws
must be removed using provided TX20 L-shaped wrench. After
removing the screws, detach the factory-provided backplate. Save
the backplate screws for the next step.
STEP 2
BACKPLATE SCREW
FACTORY-PROVIDED
BAC KP L ATE
TX20 L-Shaped Wrench
For this step, you will need:

- 8 -
STEP 3
Attach the AM5 Backplate and secure it with the four (4) saved
backplate screws.
Do not peel off the protective sticker from the AM5 Backplate!
STEP 4
Cleaning the CPU: Wipe the IHS clean using a non-abrasive cloth or
Q-tip as shown in the illustration.
STEP 3
STEP 4
IHS
NON-ABRASIVE CLOTH
AM5 BAC KP L ATE
BAC KP L ATE
SCREW
TX20 L-Shaped
Wrench
AM5 Backplate
Backplate screw
(4 pcs)
For this step, you will need:

- 9 -
STEP 1
Position the AM4 CPU Water Block onto the AM5 Motherboard.
Make sure to align the holes (as shown in the picture).
Make sure to double-check the layer of the Thermal Grease
before placing the water block onto the motherboard.
STEP 1
INSTALLING THE WATER BLOCK
STEP 5
Applying thermal compound: Apply the enclosed thermal grease
(thermal compound) on the CPU heat spreader – IHS – as shown in
the image. The layer of the thermal compound must be thin and even
in thickness over the entire surface of the IHS.
The excessive or uneven application of thermal grease
may lead to poor performance!
STEP 5
Thermal Grease
For this step, you will need:

- 10 -
STEP 3
STEP 3
With EK-Velocity² series water blocks, it is mandatory to use the
bottom port as the INLET.
Mixing the ports may result in poor thermal performance of the
water block.
Tighten the fittings in a clockwise direction until the gasket
underneath is compressed. The installation of the Velocity² water
block is now complete.
OUTLET
INLET
STEP 2
STEP 2
Secure the water block from the backside of the motherboard using
the included Allen Key 2.5mm.
Start fastening the screws in a cross pattern. Do not tighten fully until
all of the screws are partially screwed in.
The Allen Key 2.5mm must be used in a standing position! Otherwise,
the mounting screws may crack during tightening!
Make sure to orientate the backplate as illustrated. Incorrect
installation of the backplate may result in damage to the motherboard.
Allen Key 2.5 mm
For this step, you will need:
MAX TORQUE:
0.6 Nm TOP OF THE
MOTHERBOARD
AM5
BAC KP L ATE