ekwb EK-FB KIT GA X79 (UD7) Guide

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Released on 9th of February, 2012.
This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability
whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwaterblocks.com for updates.
Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box or our home page.
The barb hose fittings require only a small amount of force to screw them in; otherwise the high flow fittings might break. Th
ese fittings do not need to be tightened with much force because the
liquid seal is made using o-rings. The use of corrosion inhibitors is always recommended for any liquid cooling system.
STEP 1: GENERAL INFORMATION Sample photo of Gigabyte GA-X79-UD7 (rev. 1.0) motherboard
STEP 2: PREPARING YOUR MOTHERBOARD
1. REMOVING STOCK COOLER.
Remove all encircled screws. There are 6 screws
on the back of the motherboard that needs to be removed in order to remove the
factory installed SB/MOSFET heatpipe cooling solution.
2. CLEANING THE PCB.
Carefully detach the original stock cooler after removing all
screws securing it to the board. Wipe off the remains (by using non–abrasiv
e cloth or
qtip , as shown on sample photo) of the original thermal compound until the components
and circuit board are completely clean. EKWB recommends the use of denatured alcohol
for removing TIM leftovers.
3. APPLYING THERMAL COMPOUND. Apply thermal compound: lightly coat the
Intel X79 PCH (SB) with electrically non-conductive thermal grease - for example
Arctic Cooling MX-2 ™ or MX-4 ™. EKWB recommends to apply thermal grease in
cross form for best performance (see sample picture).
4. CUTTING THERMAL PADS. Your block comes with one (1) Thermal Pad A – 0.5mm
(100x16) which may need to be trimmed a bit
in order to fit the voltage regulation area
(VRM/MOSFET) on the motherboard’s circuit board.
WARNING: DIMENSIONS ON PICTURES BELOW ARE SCALED!
5. PLACING THERMAL PADS ON MOTHERBOARD.
Place thermal pads you cut on PCB as shown on picture bellow (PLEASE REMOVE THE PROTECTIVE FOIL FROM BOTH
SIDES OF THE THERMAL PADS PRIOR TO INSTALLATION). EK recommends using small drops of electrically non-conductive (for example: Arctic Cooling MX-2 ™ or MX-4 ™)
thermal grease on each phase regulator (that is being covered with thermal pad; see picture below) in order to even further improve the thermal performance of the EK-FB KIT
GA X79 (UD7) series water block.
X79 PCH (SB)
CPU socket
Installation and mounting manual for EK-FB KIT GA X79 (UD7) water block:
Place 0.5mm thermal pad in large strip
over marked area
and make sure all
mosfet chips are covered.
Mosfets

All disclosures, notices and warranty conditions are being written on EKWB web page. Please check terms of use. Released on 9th of February, 2012.
STEP 3: PREPARING YOUR WATER BLOCK
1. PLACING SB BLOCK ON MOTHERBOARD. Place the SB heat sink with preinstalled 2.1mm
standoffs kit gently to the motherboard or vice versa. Make sure that mounting holes are
aligned. Skip to STEP 4 on how to fasten the heat sink to the motherboard using the enclosed
screws and washers.
2. PLACING MOSFET BLOCK ON MOTHERBOARD. Apply small amount of thermal
grease around mounting holes and place POM standoffs on MOSFET water block
so the holes are concentric. Thermal paste provides enough adhesive force for
standoffs to stay in a place for easier installation. Place the water block and
2.1mm POM standoffs gently to the motherboard or vice versa. Make sure that
mounting holes are aligned.
STEP 4: ATTACHING BLOCK TO MOTHERBOARD
STEP 5: CHECKING FOR CONTACTS
Prior to fastening the screws please make sure the mounting holes on the motherboard’s
circuit board are aligned with water block.
A) SB heat sink: Use four M2.5x4 DIN7985 and washers. Tighten the screws, beginning
near the southbridge, and continue evenly outwards. Do not use excessive force when
tightening the screws!
B) MOSFET block: Use two M3x6 DIN7985 and washers. Do not use excessive force when
tightening the screws! Make sure you use enclosed washer underneath this screw.
Use the enclosed screws and washers as shown in picture below:
Temporarily r emove the water block to check for uniform surface contact
between the block and the components. Note the pattern of contact on a piece
of paper. Then repeat steps 3 and 4 to reattach the block applying more or less
pressure to the areas where you have found it necessary.
6. POSITIONING FITTINGS AND CONNECTING TO WATER CIRCUIT
Attach the liquid cooling tubes and connect the water-block(s) into the cooling circuit. EKWB recommends using EK-PSC compression fittings with the EK-FB KIT GA X79 (UD7)
series water block. You can use any opening as an inlet/outlet port. Plan your tubing routing in advance!
REQUIRED TOOLS AND MOUNTING SCREWS:
scissors philips screwdriver thermal grease Screws: 4x M2.5x4, 2x M3x6 (DIN7985)6x PVC washers
EK-PSC fitting
Tubing
PVC washer
M2.5x4 screw
Chip die thermal grease imprint
Thermal pad imprints
M3x6 screw
PVC washer
MOSFET block
SB heat sink
2.1mm POM
standoff