ekwb EK-FC 6970 Manual

All disclosures, notices and warranty conditions are being written on the back of the box. Released on 10th of May, 2011. Revision 1.1
Installation and mounting manual for EK-FC 6970 water block
This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability
whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwaterblocks.com for updates.
Before installation of this product please read important notice, disclosure and warranty conditions printed on the back of the box.
The barb hose fittings require only a small amount of force to screw them in; otherwise the high flow fittings might break. These fittings do not need to be tightened with much force because the
liquid seal is made using o-rings.
STEP 1: GENERAL INFORMATION. Sample picture of RADEON HD 6970 graphics card
STEP 2: PREPARING YOUR GRAPHIC CARD.
1. REMOVING STOCK COOLER: Remove encircled
screws:
STEP 2 cont.: PREPARING YOUR GRAPHIC CARD.
1 cont.. REMOVING STOCK COOLER. Remove all encircled screws. All heat sink
assembly screws and backplate should be removed. There are 15 screws on the back of
the graphic card.
2. CLEANING THE PCB. Carefully detach the original heat sink after removing all
fasteners securing it to the board and bracket. Wipe off the remains (by using non–
abrasive cloth or Q-tip, as shown on sample photo) of the original thermal compound
until the components and circuit board are completely clean. EKWB does not
recommend using any liquids for removing paste.
3. APPLYING THERMAL COMPOUND. Apply thermal compound: lightly coat both GPUs
and bridge chip with electrically non-conductive thermal interface material (TIM) - for
example: Arctic Cooling MX-2™ or MX-4™ thermal grease. EKWB recommends to apply
thermal grease in cross form for best performance (see sample picture).
4. CUTTING THERMAL PADS. Your block comes with thermal pads, which have to be
placed on chips (PLEASE REMOVE FOIL ON BOTH SIDES OF THERMAL PADS PRIOR
TO INSTALLATION. WARNING: DIMENSION BELLOW ARE SCALED.)
5. PLACING THERMAL PADS ON PCB. Place thermal pads on chips so that numbers on
chips match size of thermal pads. Thermal pad number 2 and 3 will have to be cut by
user to match all small power regulation chips (EKWB made sure users have more than
enough pads to cover all surfaces that need to be covered to make block fully function).
You can also use small drop of thermal grease on chips to make thermal pads more
adhesive.
6. PLACING STANDOFFS ON BLOCK. Brass standoffs are obligatory in order to attach
this water block to the printed circuit board of the graphics card. Please use the
encased key to screw them to the copper base of the water block.
1
1
1
1
1
1
1
1
3
1
2
1
Thickness 1mm
Thickness 0.5mm
1
1
1
Thickness 1.5mm
Thickness 1mm
3
1
1
2
We highly recommend
using small droplets of non-
conductive thermal grease
over each phase regulator!
Tightening the standoff:

All disclosures, notices and warranty conditions are being written on the back of the box. Released on 10th of May, 2011. Revision 1.1
7. PLACING BLOCK TO GRAPHIC CARD. During this process please make sure you align
mounting openings on PCB with threaded openings on block. Also pay attention not to
use too much force by pressing block down to PCB. Chips are prone to cracking.
8. ATTACHING BLOCK TO GRAPHIC CARD. Please place back stock backplate without
retention backplate of the GPU. By using Philips screwdriver screw in the enclosed
M3x6 screws through the backplate into the block and M3x4 screws around GPU.
EKWB recommends start screwing the screws around the GPU core and continue
outwards.
Alternative mounting method without backplate: Use nine encased M3x4
screws and nine 0.5mm PVC washers only!
STEP 3: CHECKING FOR CONTACTS
Temporarily r emove the water blocks to check for uniform surface contact between the block and the components. Note the pattern of contact on a piece of paper. Then repeat
steps 5 and 8 to reattach the block applying more or less pressure to the areas where you have found it necessary.
STEP 4: POSITIONING FITTINGS
Please use spacer on copper base (see sample picture). Screw in the fittings and plugs (please use spacers only on copper base), attach the liquid cooling tubes and connect the
water-block(s) into the cooling circuit. EKWB recommends using high flow fittings with the EK-FC 6970 series water blocks. To ensure that the tubes are securely attached to the
barb/fittings, please use hose clamps or an appropriate substitute. The use of an algaecide is always recommended for any liquid cooling system.
You can use any opening as an inlet/outlet hole.
STEP 5: INSERTING CARD IN YOUR PC CASE
Carefully lift your card with installed block and insert it in your PC case. Bear in mind that your card suddenly withstands extra weight thus again be very careful not to bend it or
cause any other unneeded moves that might damage your card or block during installation.
REQUIRED TOOLS AND MOUNTING SCREWS:
scissors philips screwdriver 5 x screws M3x6 DIN965 4x (9x alternatively) screws M3x4 DIN7985
4x (9x alternatively) M3 PVC washers
Fittings
Gasket/O-ring
Spacer
Plug
Use 4 screws M3x4 with four
0.5mm PVC washers around
GPU core only!