ekwb EK-FC980 GTX TF5 Manual

All disclosures, notices and warranty conditions are being written on the back of the box. Revision 1.0. Released on 26th of November, 2014.
Installation and mounting manual for EK-FC980 GTX TF5 Backplate
This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability
whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates. Before installation
of this product please read important notice, disclosure and warranty conditions printed on the back of the box.
STEP 1: GENERAL INFORMATION. Sample picture of GeForce 980 GTX TF5 graphics card.
STEP 2: PREPARING YOUR GRAPHICS CARD
EK-FC980 GTX TF5 Backplate is very easy to install. First install EK-FC980 GTX TF5 series water block according to its installation manual. If you
have it already installed, please check the picture below to see which mounting screws are to be left in their position and which are to be
removed. Please remove the five (5) M3x4 DIN7985 screws(marked with arrow). Do not remove the washers!
STEP 3: APPLYING THE THERMAL PADS
EK-FC980 GTX WF5 Backplate features passive cooling of the printed circuit board and it’s components therefore it is mandatory to install the
enclosed thermal pad. Please install enclosed 1mm thick thermal pad (Thermal Pad A –1mm (100x16)) as shown on the picture below. You may
need to trim the excess thermal pad.
EK-FC980 GTX TF5
Backplate
Thermal PAD A 1mm

All disclosures, notices and warranty conditions are being written on the back of the box. Revision 1.0. Released on 26th of November, 2014.
STEP 4: ATTACHING EK-FC980 GTX WF3 BACKPLATE TO THE GRAPHICS CARD
Take enclosed mounting screws and install them as shown on picture below. Depending on the variant please use the following combination of
screws:
a) Acetal top type water block: Use five (5) M3x8 DIN7991 on the back side.
b) Plexi short top type water block: Use three (3) M3x8 DIN 7991 and two (2) M3x10 DIN7991 screws with M3 nuts and washers.
HINT: Do not tighten screws until they are all positioned in their mounting holes. The backplate has milled in standoffs, so there is no fear of over
tightening of the screws. Nevertheless do not exaggerate with screwing force as there is no need for it.
By all means users must also consider that this product is intended to be used only with EK-FC980 GTX TF5 series water blocks. No other 3rd party heat
sinks or coolers are supported!
Plexi short top type water block:
Acetal top type water block:
IMPORTANT DISCLOSURES
VERY IMPORTANT NOTICE: Once the installation is completed, it is a recommended practice to test the cooling circuit for leaks prior to powering up the computer.
We recommend a 24 hour leak test prior to powering up the computer. Do not test the water block using city water pressure. This will rupture the top of the housing
and render the block unusable (and will void your warranty).While all efforts have been made to provide the most comprehensive tutorial possible, EK Water Blocks
assumes no liability expressed or implied for any consequential damage(s) occurring to your equipment as a result of using EK Water Blocks cooling products, either
due to errors or omissions on our part in the above instructions, or due to failure or defect in the EK Water Blocks cooling products.
WARRANTY:
Our products are warranted against defects in materials or workmanship for a period of 24 months beginning from the date of delivery to the final user. During this
period, products will be repaired or have parts replaced at our discretion provided that: (I) the product is returned to the agent from whom it was purchased; (II)
the product has been purchased by an end user and has not used for commercial purposes; (III) the product has not been misused, handled carelessly, or used in a
manner other than in accordance with the instructions provided describing its installation and proper use. This warranty does not confer rights other than those
expressly set out above and does not cover any claims for consequential loss or damage. This warranty is offered as an extra benefit and does not affect your
statutory rights as a consumer. This warranty is voided if the product comes in contact with aggressive chemical, chemical agents or other improper liquids or solids.
EK blocks are sealed with warranty void circular label, which proves that the block has withstood a pressure leak test. Removing it will void leak-free guarantee and
not the guarantee on the product itself. Any other RMA issues can be reported to EK Support at http://www.ekwb.com/support for further analysis.
REQUIRED TOOLS:
Philips head screwdriver scissors
M3X8 DIN7991 screw (5x)
M3X8 DIN7991
screw
M3X10 DIN7991
screw
M3 NUT
PVC washer
M3X10 DIN7991
screw
Plastic washer M3
screw
M3 nut
M3 nut