ekwb EK-XTOP Revo Dual D5 Serial Manual

Released on 1st of April, 2016.
Installation and mounting manual for EK-XTOP Revo Dual D5
Serial
This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment. EK Water Blocks assumes no liability
whatsoever, expressed or implied, for the use of these products, nor their installation. The following instructions are subject to change without notice. Please visit our web site at www.ekwb.com for updates. Before installation
of this product please read important notice, disclosure and warranty conditions printed on the back of the box.
Before you start using this product please follow these basic guidelines:
1. Please carefully read the manual before through before beginning with the installation process!
2. The EK-HFB and EK-ACF type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber o-ring gaskets.
3. The use of corrosion inhibiting coolants is always recommended for any liquid cooling system.
STEP 1: PREPARING THE PUMP
STEP 2: PREPARING MOUNTING HOLES (if not installed on fan)
Unscrew the ribbed threaded ring that attaches the Laing pump’s
original factory top and the main pump core housing with motor.
Store the original top, the original o-ring gasket and the attaching ring
in a safe place.
First you have to prepare place where the pump will be installed.
Take enclosed stickers (2 identical) which each has 4 designated holes. Be careful that between outer
holes is 142mm as shown on picture bellow.
Stick it to the PC case where you want to place the pump. Be careful of correct pump position. (Step 5)
Take a drill (5mm) and drill 8 holes on designated points.
STEP 3: INSTALLING THE Dual XTOP AND HOLDER
Dual XTOP comes in four (4) port version. Pump Top has side inlet ports and side OUTLET ports (see the picture below).
1. Take the sealing gaskets [2] and place it on each pump [3].
2. When the sealing gasket is in place take the pumps and place them onto the XTOP [1]. You can rotate the XTOP to alternate the position of the OUTLETs PORT to meet your
requirements.
3. Fix the pumps [3] on the XTOP [1] using nuts [4].
4. Take the rubber dumpers [5] and place it into the Holders [6] as shown on the picture below.
5. When the Dumpers [5] are installed in to the Holders [6] push the assembled part onto the Pumps [3]. You can rotate the pump to alternate position of the outlet ports to
meet your requirements.
6. Take the Screws M3x12 [8] and tighten them to secure the pumps to the holders. You should use Allen Key 2mm along with the M3 threaded mounting plate [7] which is
preinstalled by EK.
7. Now you have successfully assembled the unit. Position the bottom Holder [6] holes on to the pre-drilled holes and secure the assembled unit using eight enclosed M4x10
screws and the PVC washers [9].
1
.
2
.
3
3
.
4
.
5
6
5
6
4
.
2
.
7
7
8
8
9
9
OUTLET to radiator or water block
INLET
Factory original
pump top
D5 pump body with
motor
Twist LEFT to unscrew!
Mounting holes
Scale not accurate

Released on 1st of April, 2016.
STEP 4: PREPARING for mounting on fan
EK-XTOP Revo Dual D5 Come with mounting plates for
placing the unit on fan. You could place pump on 120mm
or 140 mm fan.
1. Secure Mounting plates on Holders with M4x12 and
plastic washers.
2. Secure pumps on fan with PT4.6x10 screws
2.1 If you place pumps on radiator use screws which came
with radiator.
STEP 5: ATTACHING FITTINGS
Screw in the fittings in the G1/4 threaded openings on plastic top. EKWB recommends using EK-ACF fittings with the EK-XTOP Revo Dual D5 series pump tops. To ensure that
the tubes are securely attached to the barb/fittings, please use hose clamps or an appropriate substitute.
It is mandatory to use the correct INLET and OUTLET ports:
1. The OUTLET (pressure port) is the G1/4 threaded opening on the side of the pump top housing.
2. The INLET (suction port) is the side of G1/4 threaded opening on the EK-XTOP Revo Dual D5 side face plane. Please refer to the picture on the right!
3. Port with preinstalled plug can’t be used. It is technical hole.
Use reservoir to feed the pump in order to prime it:
Connect reservoir outlet port with EK-XTOP Revo Dual D5 inlet port!
This water pump & EK-XTOP Revo Dual D5 can be used in any mounting configuration (position) apart from being
mounted upside down! Mounting the pump upside down may result in pump running dry and eventually lead to
premature failure of the pump!
IMPORTANT DISCLOSURES:
VERY IMPORTANT NOTICE: Once the installation is completed, it is a recommended practice to test the cooling circuit for leaks prior to powering up the computer. We
recommend a 24 hour leak test prior to powering up the computer. Do not test the water block using tap water pressure. This will rupture the top of the housing and render
the block unusable (and will void your warranty).While all efforts have been made to provide the most comprehensive tutorial possible, EK Water Blocks assumes no liability
expressed or implied for any consequential damage(s) occurring to your equipment as a result of using EK Water Blocks cooling products, either due to errors or omissions on
our part in the above instructions, or due to failure or defect in the EK Water Blocks cooling products.
WARRANTY:Our products are warranted against defects in materials or workmanship for a period of 24 months beginning from the date of delivery to the final user. During this
period, products will be repaired or have parts replaced at our discretion provided that: (I) the product is returned to the agent from whom it was purchased; (II) the product
has been purchased by an end user and has not used for commercial purposes; (III) the product has not been misused, handled carelessly, or used in a manner other than in
accordance with the instructions provided describing its installation and proper use. This warranty does not confer rights other than those expressly set out above and does
not cover any claims for consequential loss or damage. This warranty is offered as an extra benefit and does not affect your statutory rights as a consumer. This warranty is
voided if the product comes in contact with aggressive UV additives or other improper liquids.
Any other RMA issues can be reported to www.ekwb.com/support for further analysis.
REQUIRED TOOLS: Allen key 2.5mm and allen key 2mm ( Both are enclosed)
OK
OK
Mounted upside down? NOT OK!
INLET
Plastic washer M4
Screw M4x10,
Screw PT 4.6x10
OUTLETs to radiator or water block