Electrex KILO F RJ45 User manual

INSTALLATION INSTRUCTIONS
KILO F RJ45 and NET D6 READINGS
ELECTREX
KILO D6 ADDR 247
VER X.XX
SN XXXXXX
MAC XXXXXXXXXXXX
MEASURE LIST TABLE
(The parameters available vary according to instrument confi guration)
Short keypress
Long keypress
P P Avg Imp P Avg Exp P MD Imp P MD Exp
Q Q Avg Imp Q Avg Exp Q MD Imp Q MD Exp
S S Avg Imp S Avg Exp S MD Imp S MD Exp
PF
Short keypress
Long keypress
U L-N / f U THD L-N U L-N Min U L-N Max
U L-L / f U THD L-L U L-L Min U L-L Max
Short keypress
In I I THD I Max I AVG I MD
Short keypress
Long keypress
Ea Imp ∑ Ea Imp P Ea Exp ∑ Ea Exp P Ea Imp ∑
Fase
Er Ind Imp ∑ Er Ind Imp P Er Ind Exp ∑ Er Ind Exp P Er Ind Imp ∑
Fase
Er Cap Imp ∑ Er Cap Imp P Er Cap Exp ∑ Er Cap Exp P
Es Imp ∑ Es Imp P Es Exp ∑ Es Exp P
C1 Pulse ∑ C1 Pulse P
LEGEND OF PARAMETERS AND SYMBOLS
L-N Phase Neutral UVoltage
L-L Phase Phase ICurrent
THD Total Harmonic Distortion In Neutral current
Avg Average (rolling) value PActive Power
MD Maximum Demand QReactive Power
Imp Import value SApparent Power
Exp Export value PF Power Factor
Ind Inductive Ea Active Energy
Cap Capacitive Er Reactive Energy
Min Minimum values (10 cycles time base) Es Apparent Energy
Max Maximum values (10 cycles time base) f Frequency
CNT ∑ Pulse count (total)
CNT P Pulse count (partial)
Keep pressed for 2
seconds to display:
- Type of instrument
- Firmware version
- Serial number
- RS485 address
MECHANICAL CHARACTERISTICS
Case Self-extinguishing plastic material class V0
Protection degree IP40 on front panel, IP20 terminals side
Size 105 x 90 x 58 mm (6 DIN modules)
VOLTAGE INPUT
Direct insertion Up to 300 Vrms phase-neutral or 520 Vrms phase to phase
With external VT: Primary: programmable (max. 400 kV)
Secondary: programmable (max. 300 V)
Overload: 900 Vrms phase to phase for 1 sec
Aux. power supply 85/265Vac +/- 10% 50/60Hz
Self consumption: < 2 watt
MODELS
PFNK6-FH719-0M0 KILO F RJ45 D6 H 85÷265V 1DI 2DO ENERGY
ANALYZER & DATA MANAGER
PFNK6-FQ719-0MM KILO F RJ45 D6 PQ 85÷265V 1DI 2DO ENERGY
ANALYZER & DATA MANAGER
PFNK6-FQ519-121 KILO F NET D6 PQ WEB 85÷265V 1DI 2DO ENERGY
ANALYZER & WEB DATA MANAGER
PFNK6-FQ519-F21 KILO F NET D6 PQ FULL 85÷265V 1DI 2DO ENERGY
ANALYZER & WEB DATA MANAGER
PFNK6-1Q519-F21 KILO NET D6 PQ FULL 85÷265V 1DI 2DO ENERGY
ANALYZER & WEB DATA MANAGER
PFNK6-FQ519-A21 KILO F NET D6 PQ WEB CHARTS 85÷265V 1DI 2DO
ENERGY ANALYZER & WEB DATA MANAGER
Further documentation may be downloaded from our web site www.electrex.it.
This document is owned by company AKSE that reserves all rights.
DECLARATION OF CONFORMITY
Akse hereby declares that its range of products complies with the following directives EMC
89/336/EEC 73/23CE 93/68 CE and complies with the following product’s standard
CEI EN 61326 – IEC 61326 CEI EN 61010 – IEC 61010.
The product has been tested in the typical wiring confi guration and with peripherals
conforming to the EMC directive and the LV directive.
COPYRIGHT
Electrex is a trademark of Akse S.r.l. All rights reserved.
It is forbidden to duplicate, adapt, transcript this document without Akse written
authorization, except when regulated accordingly by the Copyright Laws.
WARRANTY
This product is covered by a warranty against material and manufacturing defects for a 24
months period from the manufacturing date.
The warranty does not cover the defects that are due to:
• Negligent and improper use
• Failures caused by atmospheric hazards
• Acts of vandalism
• Wear out of materials
• Firmware upgrades
Akse reserves the right, at its discretion, to repair or substitute the faulty products
The warranty is not applicable to the products that will result defective in consequence of
a negligent and improper use or an operating procedure not contemplated in this manual.
RETURN AND REPAIR FORMALITIES
Akse accepts the return of instruments for repair only when authorized in advance. The
transport costs are at customer charge.
RE-SHIPPING OF REPAIRED PRODUCT
The terms for re-shipment of repaired products are ex-works, i.e. the transport costs are
at customer charge.
Products returned as detective but found to be perfectly working by our laboratories, will
be charged a fl at fee to account for checking and testing time irrespective of the warranty
terms.
SAFETY
This instrument was manufactured and tested in compliance with IEC 61010-1 CAT III -
300V class 2 standards for operating voltages up to 300 VAC rms phase to neutral.
In order to maintain this condition and to ensure safe operation, the user must comply with
the indications and markings contained in the following instructions:
• When the instrument is received, before starting its installation, check that it is
intact and no damage occurred during transport.
• Before mounting, ensure that the instrument operating voltages and the mains
voltage are compatible then proceed with the installation.
• The instrument power supply needs no earth connection.
• The instrument is not equipped with a power supply fuse; a suitable external
protection fuse must be foreseen by the contractor.
• Maintenance and/or repair must be carried out only by qualifi ed, authorized
personnel
• If there is ever the suspicion that safe operation is no longer possible, the instrument
must be taken out of service and precautions taken against its accidental use.
• Operation is no longer safe when:
1) There is clearly visible damaged.
2) The instrument no longer functions.
3) After lengthy storage in unfavorable conditions.
4) After serious damage occurred during transport
The instruments must be installed in respect of all the local regulations.
OPERATOR SAFETY
Warning: Failure to observe the following instructions may lead to a serious danger of
death.
• During normal operation dangerous voltages can occur on instrument terminals and
on voltage and current transformers. Energized voltage and current transformers
may generate lethal voltages. Follow carefully the standard safety precautions while
carrying out any installation or service operation.
• The terminals of the instrument must not be accessible by the user after the installation.
The user should only be allowed to access the instrument front panel where the
display is located.
• Do not use the digital outputs for protection functions nor for power limitation functions.
The instrument is suitable only for secondary protection functions.
• The instrument must be protected by a breaking device capable of interrupting both
the power supply and the measurement terminals. It must be easily reachable by the
operator and well identifi ed as instrument cut-off device.
• The instrument and its connections must be carefully protected against short-circuit.
Precautions: Failure to respect the following instructions may irreversibly damage to the
instrument.
• The outputs and the options operate at low voltage level; they cannot be powered by
any unspecifi ed external voltage.
• The application of currents not compatible with the current inputs levels will damage
to the instrument.

DESCRIPTION OF KEYS
Short keypress Long keypress
Confi rm parameter Confi rm setup
Modify parameter
Modify parameter
Go to previous value Go to previous page
Go to next value Go to next page
Exit without saving the confi guration
RESET
MEAS
HARM
PAGE
STAT
ELECTREX
KILO D6 ADDR 247
VER X.XX
SN XXXXXX
MAC XXXXXXXXXXXX
SET
RESET
MEAS
HARM
PAGE
ELECTREX
KILO D6 ADDR 247
VER X.XX
SN XXXXXX
MAC XXXXXXXXXXXX
MEAS
HARM
PAGE
STAT
SET
ELECTREX
KILO D6 ADDR 247
VER X.XX
SN XXXXXX
MAC XXXXXXXXXXXX
ELECTREX
KILO D6 ADDR 247
VER X.XX
SN XXXXXX
MAC XXXXXXXXXXXX
PAGE
STAT
SET
RESET
MEAS
HARM
PAGE
STAT
SET
RESET
ELECTREX
KILO D6 ADDR 247
VER X.XX
SN XXXXXX
MAC XXXXXXXXXXXX
ETH
ETH
WIFI
192.168.027.001
192.168.026.001
U
1N
H
20.0 %
DEVICE SETUP
RESET
STAT
SET
RESET
MEAS
HARM
ELECTREX
KILO D6 ADDR 247
VER X.XX
SN XXXXXX
MAC XXXXXXXXXXXX
RICHIESTA PASSWORD 0000 ... 9999 0000
COUNTERS
TOT N, Y
PAR N, Y
MAX N, Y
MD N, Y
COUNTERS
TOT
PAR
MAX
MD
N
N
N
N
CHANGE PWD
PWD 0000...9999 0000
RESET
MEASURES
HARMONICS
PAGE
STAT
Select measure (U1N, U2N, U3N, I1, I2, I3)
Select harmonic (from H2 to H32 - value in %)
Exit without saving the confi guration
In development
The “STAT” page shows the assigned IP address of the LAN and WI-FI port (if present)
On “MEAS” page are displayed the main measures of the device (voltage, current, power,
energy, etc.).
On “HARM” page are displayed the harmonics (from 2nd to the 32nd) for voltage and current.
The “RESET” page allows to reset the total (TOT) and partial (PAR) energy counters, the
minimum and maximum values (MAX) and the historical maximum values (MD).
SETUP SEQUENCE
PAGE PARAMETERS VALUES AVAILABLE DEFAULT
PASSWORD REQUEST 0000 ... 9999 0000
MEAS-A Note n.1
NET 3PH-4W, 2PH-2W, 1PH-2W, 3PH-3W-2C 3P-4W
IMP / EXP EXP
IMAX 500, 2000, 8000 8000
VT 1...400000 / 1...300 1/1
MEAS-A
NET
IMAX
VT
3P-4W / EXP
8000
000001 / 001
MEAS-B Note n.2
I AVG 1...60 (MINUTES) 8
P AVG 1...60 (MINUTES) 15
MEAS-B
AVG
AVG
8
15
I
P
RS485-A Note n.3
MODE SLAVE, MASTER SLAVE
TOUT 100...10000 (ms) 3000
RETR 0...9 3
RS485-A
MODE
TOUT
RETR
SLAVE
03000
3
RS485-B Note n.4
ADDR 1 ... 247 247
COM1 2400, 4800, 9600, 19200, 38400 38400
Bit Dati 5...8 8
Parità N = none, E = even, O = odd N
Bit di stop 1 o 2 2
ST (Silent Time) 0...5000 (ms) 100
RS485-B
ADDR
COM1
COM2
ST
247
38400 / 8
N / 2
0150
ETH Note n.5
DHCP N, Y N
IP xxx.xxx.xxx.xxx 192.168.027.001
NETM xxx.xxx.xxx.xxx 255.255.255.000
GWAY xxx.xxx.xxx.xxx 127.000.000.001
ETH
DHCP
IP
NETM
GWAY
N
192.168.027.001
255.255.255.000
127.000.000.001
WIFI Note n.5
DHCP N, Y N
IP xxx.xxx.xxx.xxx 192.168.026.001
NETM xxx.xxx.xxx.xxx 255.255.255.000
GWAY xxx.xxx.xxx.xxx 127.000.000.001
WIFI
DHCP
IP
NETM
GWAY
N
192.168.026.001
255.255.255.000
127.000.000.001
NET Note n.6
DEF ETH, WIFI ETH
ETH N, Y Y
WIFI N, Y Y
NET
DEF
ETH
WIFI
ETH
Y
Y
NET
DEF
ETH
WIFI
ETH
Y
Y
LCD Note n.7
DIM DISABLE, ENABLE DISABLE
TIME 1...90 (sec) 3
LIGHT 300...1000 500
PULSE DISABLE, ENABLE ENABLE
LCD
DIM
TIME
LIGHT
PULSE
DISABLE
3
0500
ENABLE
CHANGE PWD
PWD 0000...9999 0000

INPUT & OUTPUT CONNECTION EXAMPLE
Digital Inputs
Supply voltage (external): from 10 to 30
Vdc
Current consumption: from 2 to 10mA
Max. count frequency 10 or 100Hz
N.B. For gas meters a galvanic separation is
needed per ATEX standards
Digital outputs (optocoupled NPN
transistor type for DIN 43864)
Maximum applicable voltage: 27 Vdc
Maximum switchable current: 27 mA
C
19
1
20
2
21
AUX
IN/OUT
!
Common
21
20
19
DO2
DO1
C
10
2
11
1
12
AUX
IN/OUT
!
INPUT & OUTPUT CONNECTION
S1 S2 S1 S2 S1 S2
19 2017 18V1 V2 V3
AUX
IN/OUT
VOLTAGE INPUTS POWER
SUPPLY
CURRENT INPUTS
N21
T
B A 10 11 12
RS-485
AUX
IN/OUT
I1 I2 I3
NO
C
NC
NO
C
NC
FROM:
- TRASDUCER WITH FREE POTENTIAL CONTACT
- UTILITY METER
- SWITCH STATUS
- ALARM STATUS
R
e
l
a
y
R
e
l
a
y
230 V~
24V =
N L
- +
DI (+)
11
10
DI (-)
12
ETHERNETEXPBUS
DIP FUNCTION SLAVE MASTER *
1 Line termination resistance (120 Ohm) OFF ON
2 Fail safe resistance B (-) OFF ON
3 Fail safe resistance A (+) OFF ON
4 Not used OFF OFF
* with RS-485 Master PUK activated
1
ON
234
1
ON
234
LAN 10/100 ETHERNET PORT
The instrument is equipped with a Ethernet Lan 10/100 Auto-MDI/MDIX port.
For the connection can be used a data cable straight or crossover.
Note: the port is not a PoE (Power over Ethernet = device power supply via the Lan port)
type. The connection of the device to a PoE port is anyway accepted. The power supply
anyway must be always provided by an external power supplier.
DIP-SWITCH CONFIGURATION
EXPBUS PORT
The ExpBus port, confi gurable via Ethernet port on web pages:
- uses a multicast communication rated at 250kb/sec with collision management
- max cable length : 10 meters
- manages up to 16 modules (but technically can manage up to 126)
- uses the UTP cable, 4 wires used:
2 for the power supply at 9 Vdc
2 for the bidirectional communication
The modules will also power supply the ExpBus port
The cable must be connected in in-out modality (multidrop) as per the RS485 Bus.
MESSAGE “CFG ERROR”
During the set up operation a “CFG ERROR” message could appear. This means that
some wrong parameters are inserted.
CFG ERROR
Vcc
L H
Gnd
NOTE n.1
NET 3PH-3W-2CT 2 phases 3 wires, triangle
3PH-4W 3 phases 4 wires, Star
2PH-2W 2 phases 2 wires, biphase
1PH-2W 1 phase 2 wires, monophase
IMP/EXP IMP = Only import, EXP = Import/Export
CT Primary / Secondary of the current transformer (CT)
VT Primary / Secondary of the voltage transformer (VT)
NOTE n.2
P AVG Integration time of the average value (AVG) and peak value (MD) for
power (from 1 to 60 minutes)
I AVG Integration time of the average value (AVG) and peak value (MD) for
current (from 1 to 60 minutes)
NOTE n.3
MODE SLAVE RS485 port set as Slave for the network.
MASTER RS485 port set as Master for the network.
TOUT Predetermined time in which a given operation must be
terminated
RETR Number of communication attempts on the RS485 port
NOTE n.4
NOTE n.5
DHCP Enable / Disable the search for a DHCP server in the network
IP IP address of the network interface
NETM Subnet mask: defi nes the belonging range of a host within an IP
subnetwork
GWAY IP address of the gateway
NOTE n.6
DEF Select the network interface to be used as default for communication.
ETH Enable / Disable the Ethernet port (LAN)
WIFI Enable / Disable the Wi-Fi port
NOTE n.7
DIM Enable / Disable dimming of the display
TIME Time in seconds after which the display luminosity is reduced. (With DIM
enabled)
LIGHT Luminosity level of the display
PULSE Enable / Disable the fl ashing of the sine wave symbol light near the
Electrex logo.

akse srl Via Aldo Moro, 39 42124 Reggio Emilia Italy
Tel. [phone] Fax [phone] [email protected] www.akse.it
P.I. 01544980350 R.E.A. 194296 Cap. Soc. Euro 85.800,00 i.v.
Subject to modifi cation without notice.
Edition 2015 04 24 ENG0083
STAR 4W (4 WIRES) 3PH-4W BT
The instrument is equipped with a separate power supply. The power supply terminals are
numbered (17 e 18). Use cables with max cross-section of 2,5 mm2 if stranded, 4 mm2 if
rigid.
POWER SUPPLY
Voltage connection: Use cables with max cross-section of 2,5 mm2 if stranded 4 mm2 if rigid and connect them to the clamps marked VOLTAGE INPUT on the instrument according to
the applicable diagrams that follow.
Current transformers connection:
Connect the the amperometric signal coming from the fl exible CT output(s) to the terminals marked I1, I2, I3 (CURRENT INPUT) of the instrument according to the applicable diagrams
that follow. Respect scrupulously the phase pairing between the voltage and current signals (RST) and the direction of insertion of the CT (S1-S2). Failure to comply with such
correspondence and connection diagrams will result in measurement errors.
ATTENTION: Use exclusively Electrex fl exible split current transformers of the series FCTS. Do not use standard current transformers (/ 1 / 5A), their use will damage the
instrument.
VOLTAGE AND CURRENT CONNECTION
STAR 4W (4 WIRES) 3PH-4W MT SINGLE PHASE (2 WIRES) 1PH-2W
TRIANGLE 3W (3 FILI) 3PH-3W BI-PHASE (2 FILI) 2PH-2W
Made in Italy
Pensato, progettato e prodotto in Italia
Engineered and manufactured in Italy
S1 S2 S1 S2 S1 S2
19 2017 18V1 V2 V3
AUX
IN/OUT
VOLTAGE INPUTS POWER
SUPPLY
CURRENT INPUTS
N21
T
B A 10 11 12
RS-485
AUX
IN/OUT
I1 I2 I3
L3
L2
L1
N
S1 S2 S1 S2 S1 S2
19 2017 18V1 V2 V3
AUX
IN/OUT
VOLTAGE INPUTS POWER
SUPPLY
CURRENT INPUTS
N21
T
B A 10 11 12
RS-485
AUX
IN/OUT
I1 I2 I3
L3
L2
L1
S1 S2 S1 S2 S1 S2
19 2017 18V1 V2 V3
AUX
IN/OUT
VOLTAGE INPUTS POWER
SUPPLY
CURRENT INPUTS
N21
T
B A 10 11 12
RS-485
AUX
IN/OUT
I1 I2 I3
L1
N
S1 S2 S1 S2 S1 S2
19 2017 18V1 V2 V3
AUX
IN/OUT
VOLTAGE INPUTS POWER
SUPPLY
CURRENT INPUTS
N21
T
B A 10 11 12
RS-485
AUX
IN/OUT
I1 I2 I3
L2
L1
S1 S2 S1 S2 S1 S2
19 2017 18V1 V2 V3
AUX
IN/OUT
VOLTAGE INPUTS POWER
SUPPLY
CURRENT INPUTS
N21
T
B A 10 11 12
RS-485
AUX
IN/OUT
I1 I2 I3
85-265VAC 100-375VDC FUSE
T 500mA
S1 S2 S1 S2 S1 S2
19 2017 18V1 V2 V3
AUX
IN/OUT
VOLTAGE INPUTS POWER
SUPPLY
CURRENT INPUTS
N21
T
BA101112
RS-485
AUX
IN/OUT
I1 I2 I3
L3
L2
L1