Elite Screens Cinema235 Series User manual

Rev.051811‐
A
www.elitesc
r













A
S
r
eens.com

F
Ci
n

F
ixed
F
n
e
m
 
info
@
F
rame
P
m
a2
3
User’s
@
elitescreens.com
P
rojecti
o
3
5
S
Guide

o
n Scre
e
S
er
i

e
n
i
es

1

2
Rev.051811‐AS
www.elitescreens.com[email protected]
Pleasemakesureallpartslistedbelowareincludedbeforeproceedingwiththeinstallation.


1.FramePartsx6pcs(4Top&Bottomframepcs+2Sideframepcs)
2.TensionRodsx6pcs(4Top&Bottomframerods+2Siderods)
3.ScreenMaterialx1pc
4.CenterJointsx2pcs
5.ElbowJointsx4pcs
6.WallBracketsx2‐3pcs(dependingonsize)
7.Screwsx16pcs
8.UserGuidex1pc
9.CenterSupportBarx1‐2pcs(dependingonsize)
10.SupportJoinerx2‐4pcs(dependingonsize)
11.FixPlatesx30‐90pcs(dependingonsize)
12.BlackClothBackingx1pc(AcousticPro1080modelsonly)


AssembletheFrame
1.InserttheCenterJointConnectortothehorizontalframepieceandsecurewithscrews.







Parts List for the Cinema235 Series
Installation Instructions

3
Rev.051811‐AS
www.elitescreens.com[email protected]
2.InserttheotherhorizontalframepiecetotheCenterJointconnectorandsecurewithscrews.







Note:Tomakesuretheframepieceslineupcorrectly,donottightenthescrewsuntilassemblyiscomplete.
3.InsertbothElbowJointconnectorsintothelonghorizontalframe(seefig.1).


Push Push
Joint
Long frame
( fig.1)
Push Push
Short frame
Short frame
1/2Longframe
Push

4
Rev.051811‐AS
www.elitescreens.com[email protected]
Push Push
( fig.2)
Insert the exposed ends of the joint connectors
into the short (vertical) frame and align the four
corners so that they meet at perfect right angles
4.Joinallfourframepartstogetherfollowingthestepsshowedbelow(seefig.2)
















5.Makesureallfourcornersjoincorrectlytoformaperfectrectangle,thenfastenthefourangles
togetherbyusingtheincludedjointscrews.(seefig.3)

Screw
( fig.3)

5
Rev.051811‐AS
www.elitescreens.com[email protected]
TensionRod(Horizontal)x4
TensionRod(Vertical)x2
AttachtheScreenMaterialtotheFrame
1.LayoutthematerialandTensionRodsonaclean&drysurface.InserttheTensionRodsthroughthe
sleevesaccordingtotheircorrespondinglengthsoneachedgeofthescreen(seefig.4).
















2.Placethescreenmaterialonthebackoftheframeandinsertthetensionrodsintothegrooves
runningofeachcorneroftheframe.InserttheFixPlatestothebackoftheframetosecuretherods
intoplacecreatingtensionforaflatsurface(seefig.5&6).


Push
( fig.5)
Viewing surface
(Front of screen) Steel rod
fix plate
Steel rod
Push
( fig.4)
Steel rod
Screen
Push