Elkay EDFP19C*A Installation manual

EDFP19C*A
97155C (Rev. B - 9/02)
FIG. 1 FIG. 2
Installation/Care/Use Manual
Semi-Recessed Wall Mount Fountain with FLEXI-GUARD®
To assure you install this model easily and correctly, PLEASE READ THESE SIMPLE
INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK YOUR INSTALLA-
TION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL AND OTHER APPLICABLE
CODES. After installation, leave these instructions inside the fountain for future reference.
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
1
SEE FIG. 3
SEE FIG. 4
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO
WATER LINES IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY
OCCUR AWAY FROM THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK
INTOAFOUNTAIN, CREATING AN ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN
INCREASE IN THE METAL CONTENT OF THE WATER. THIS CONDITION IS AVOIDABLE BY USING
THE PROPER MATERIALS AS INDICATED. ANY DRAIN FITTINGS PROVIDED BY THE INSTALLER
SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE FOUNTAIN FROM THE BUILDING
PLUMBING SYSTEM.
Installer
NOTE: WATER FLOW
DIRECTION
BUILDING WATER INLET
SERVICE STOP
(NOT FURNISHED)
1/4" O.D. TUBE
WATER INLET
TO COOLER
3/8" O.D. UNPLATED
COPPER TUBE CONNECT
COLD WATER SUPPLY

EDFP19C*A
97155C (Rev. B - 9/02)
LEGEND: A = RECOMMENDED WATER SUPPLY LOCATION, 3/8 O.D. UNPLATED COPPER TUBE CONNECT. B = RECOMMENDED LOCATION FOR WASTE OUTLET, 1-1/4 O.D. DRAIN. C = 1-1/4 TRAP NOT FURNISHED. D = MOUNTING HOLES FOR BASIN HANGER STRAP. E = MOUNTING HOLES FOR FOUNTAIN (VANDAL RESISTANT INSTALLATION ONLY). F = MOUNTING HOLES FOR FOUNTAIN (EASY ACCESS INSTALLATION ONLY).
FINISHED FLOOR
PAGE 2

EDFP19C*A
97155C (Rev. B - 9/02)
DRAIN
3
4
15
12
14
16
BUBBLER ASSY
NOTE:
WHEN INSTALLING REPLACEMENT BUBBLER
AND PEDESTAL, TIGHTEN NUT (ITEM 16)
ONLYTO HOLD PARTS SNUG IN POSITION.
DO NOT OVER TIGHTEN.
13
2
FIG. 4FIG. 3
INSTALLATION INSTRUCTIONS
1. Connecting lines to be unplated copper and thoroughly flushed to remove all foreign matter before connec
tion to fountain.
2. Make water supply connections from service stop to the 3/8" O.D. unplated copper tube coming out of the
strainer. Turn on water supply and check for leaks. Newly installed water supply line should be insulated
after leak check is completed. DO NOT SOLDER TUBES INSERTED INTO THE STRAINER AS
DAMAGE TO THE O-RINGS MAY RESULT.
3. These products are designed to operate on 20-105 PSIG supply line pressure. If inlet pressure is above
105 PSIG, a pressure regulator must be installed in the supply line. Any damage caused by reason of
connecting these products to supply line pressures lower than 20 PSIG or higher than 105 PSIG is not
covered by warranty.
4. Check stream height from bubbler. Stream height is factory set at 35 PSI. If supply pressure varies
greatly from this, turn adjustment screw on the regulator (Item 19). Clockwise adjustment will raise stream
height and counter-clockwise will lower stream height. For best adjustment stream should hit basin
approximately 6-1/2" (165mm) from bubbler.
TROUBLE SHOOTING AND MAINTENANCE
1. Orifice Assy: Mineral deposits on orifice can cause water flow to spurt or not regulate. Mineral deposits
may be removed from orifice with a small round file not over 1/8" diameter or a small diameter wire.
CAUTION: Do not file or cut orifice materials.
2. Stream Regulator: If orifice is free of material deposits, regulate flow according to instruction 4 stated
above.
3. Actuation of Quick Connect Water Fittings: Cooler is provided with lead-free connectors which utilize
an o-ring water seal. To remove tubing from the fitting, relieve water pressure, push in on the gray collar
while pulling on the tubing (See Figure 2). To insert tubing, push tube straight into the fitting until it
reaches a positive stop, approximately 3/4".
4. CAUTION: Cleaning of Bronzetone Models requires special care. Outer surfaces must be cleaned with a
mild detergent or a mixture of vinegar and water only, rinsed and wiped dry. Abrasive and acidic cleaners
may eventually damage the Bronzetone finish.
PAGE 3

EDFP19C*A
97155C (Rev. B - 9/02)
DESCRIPTION
21222C
40575C
50074C
40572C
22905C
22907C
22718C
21560C
22611C
21708C
22574C
56073C
40322C
56011C
55997C
75580C
40045C
15005C
61314C
50986C
75555C
50198C
70278C
21710C
20415C
55996C
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
NS
NS
PARTNO.ITEM NO.
PARTS LIST
5
17
9819
23
22
7
10
18
21
24
20
11
6
PAGE 4
Basin
Strainer & Ferrule Assy
Gasket - Tailpipe
Tailpipe
Panel - Left Hand Side
Panel - Right Hand Side
Panel - Front
Panel - Access
Baseplate
Push Bar Assy
Regulator Mounting Bracket
Bubbler Assy
Orifice Assy
Housing Assy
Pedestal
Locknut 3/8-18
Hex Nut 1-5/16
Retaining Nut
Regulator
Regulator - Holder
Clip
Bushing - Nylon
Rod - Support
Angle - Wall Mounting
Basin Hanger Strap
Strainer
www.DrinkingFountainDoctor.com 800-518-5388