Elkay VRC8FR 1C Series Installation manual

VRC8FR*1C
Page 1 98966C (Rev. B - 2/13)
Uses HFC-134A refrigerant
VRC Series Barrier-Free Water Coolers
INSTALLATION, CARE & USE MANUAL
TM
2, 3, 5
8
23, 61, 62
43
24, 30
42
20
25
21
21
21
50
45
49
See Fig. 4
10
9, 12, 13
1, 4
6, 7, 22, 41
11
See Fig. 3
21
19
38, 39
42
16
45
32
33
37
51
59, 60
54
55
Fig. 1
63
21

VRC8FR*1C
Page 298966C (Rev. B - 2/13)
Fig. 2
REDUCE HEIGHT BY 3” FOR INSTALLATION OF CHILDRENS ADA COOLER
ADAREQUIREMENT
*
LEGEND/LEYENDA/LÉGENDE A = RECOMMENDED WATER SUPPLY LOCATION. SHUT OFF VALVE (NOT FURNISHED) TO ACCEPT 3/8” O.D. UNPLATED
COPPER TUBE.
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4” O.D. DRAIN C = 1-1/4 TRAP NOT FURNISHED** D = ELECTRICAL SUPPLY (3) WIRE RECESSED BOX E = INSURE PROPER VENTILATION BY MAINTAINING 6" (152 mm) (MIN.) CLEARANCE FROM CABINET LOUVERS TO WALL. F = 7/16 BOLT HOLES FOR FASTENING UNIT TO WALL

VRC8FR*1C
Page 3 98966C (Rev. B - 2/13)
Fig. 3
VANDAL RESISTANT BUBBLER DETAIL
DETALLE DEL GRIFO RESISTENTE AL VANDALISMO
DESCRIPTION DU BARBOTEUR RESISTANT AU VANDALISME
Basin
Estanque
Bassin
IMPORTANT
ALL SERVICE TO BE PERFORMED BY
AN AUTHORIZED SERVICE PERSON
HANGER BRACKETS & TRAP
INSTALLATION
1) Remove hanger bracket fastened to back of cooler by removing one (1)
screw.
2) Mount the hanger bracket and trap as shown in Figure 2.
NOTE: Hanger Bracket MUST be supported securely. Add fixture support
carrier if wall will not provide adequate support.
IMPORTANT:
y6 1/4 in. (159mm) dimension from wall to centerline of trap must be
maintained for proper fit.
yAnchor hanger securely to wall using all five (5) 1/4 in. dia. mounting
holes.
3) Install straight valve for 3/8" O.D. tube.
INSTALLATION OF COOLER
4) Hang the cooler on the hanger bracket. Be certain the hanger bracket is
engaged properly in the slots on the cooler back as shown in Figure 2.
5) Loosen the two (2) screws holding the lower front panel at the bottom of
cooler base and two (2) screws at the top (Use torx bits sold separately).
Remove the front panel and set aside.
6) Connect water inlet line--See Note 4 of General Instructions.
7) Remove the slip nut and gasket from the trap and install them on the cooler
waste line making sure that the end of the waste line fits into the trap.
Assemble the slip nut and gasket to the trap and tighten securely. Recom-
mend fastening cooler to wall using 7/16 bolt holes. (see fig.2, "F")
START UP
Also See General Instructions
8) Stream height is factory set at 45-50 PSI. If supply pressure varies
greatly from this, adjust screw using the access hole in the pushbutton
(insert screwdriver). CW adjustment will raise stream and CCW adjust-
ment will lower stream. For best adjustment, stream should hit basin
approximately 6-1/2” (165mm) from bubbler.
Stainless Steel
PANEL COLOR
COLOR TABLE Item No. 37
Part No.
Item No. 32
Part No. Item No. 33
Part No. Item No. 34 Part No. Item No. 35 Part No. Item No. 36 Part No.
28525C 28519C 28516C 28528C 28522C 22955C
15
1
4
1

VRC8FR*1C
Page 498966C (Rev. B - 2/13)
35
Fig. 4
15
23
25
45 (8)
1
4
32
30
24
46
33
46
53 31
48 40 44
14,17,18
34
52
26
47 (4)
27 28
36
46 46
46
46
31
53
45 (6)
29
1
62
61
50
59
60

VRC8FR*1C
Page 5 98966C (Rev. B - 2/13)
Fig. 5
Thermostat Installation Detail
Fig. 6
Heater Strip Detail
WARNING!
This unit is frost resistant down to 0° F with no wind.
Prevailing winds can reduce the ability of the heater
element to prevent light freezing. If the ambient air
temperature will drop below 0° F, the cooler needs to
be drained of all water by blowing out all water lines,
evaporator (item 20), and the drain trap. A heater
strip is used to heat the unit and will begin to cycle
at 40° +/- 5° F. A check at this temperature will
ensure the heater is working and the unit is resis-
tant to light freezing.
ALSO, MAKE SURE THERE ARE NO PLASTIC OR
FLAMMABLE COMPONENTS DIRECTLY ABOVE
THE HEATER STRIP. Wiring Diagram
56
21
21
57
54
55
58
45
58

VRC8FR*1C
Page 698966C (Rev. B - 2/13)
PRINTED IN U.S.A.
IMPRESO EN LOS E.E.U.U.
IMPRIMÉ AUX É.-U.
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484
REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640
56305C
100806740570
101474551730
15009C
19037000
30664C
31490C
35839C
35768C
35870C
36322C
36173C
36167C
50986C
45866C
56092C
15005C
61313C
66703C
66810C
70002C
70009C
600985451640
56121C
28963C
22897C
45662C
45737C
75672C
100147140560
28596C
See Color Table
See Color Table
See Color Table
See Color Table
See Color Table
See Color Table
66743C
56237C
40045C
70018C
75524C
55996C
45736C
75570C
75661C
70864C
56033C
66576C
45930C
27124C
55931C
28617C
35906C
35907C
35909C
70432C
75506C
75588C
75589C
110868642550
160270508640
75583C
75520C
75523C
28551C
Gasket - Bubbler
Grommet - Compressor Mtg.
Stud - Compressor Mtg.
Nipple - Bubbler
Clip - Compressor Mtg.
Fan Blade
Fan Motor
Cold Control
Cover - Relay
Power Cord
Compressor Serv. Pak EMI 70
Overload
Relay
Holder - Regulator
Bubbler Assy.
Tubing - Poly (Cut To length)
Retaining Nut
Regulator
Drier
Evaporator Assembly
Screw - #10 x 1/2” Lg. HHSM
Screw - Fan Motor
Drain Plug 1-1/2
Elbow - Drain
Basin - Stainless Steel
Panel - Bottom Dispenser
Button - Push
Sleeve - Push Button
Cap Screw
Gasket - Drain
Panel - Screen
Panel - RH Rear
Panel - LH Rear
Panel - RH Dispenser Side
Panel - LH Dispenser Side
Panel - Dispenser Front
Panel - Front Lower
Condenser
Shroud Fan
Hex Nut
Hex Nut - Fan Blade
Clip (Front & Rear Panels)
Strainer (See “General Instructions”)
Half Nut - Regulator
Screw - #10 x .50 Pinned Torx
Screw - #8 x .50 Pinned Torx
Screw - #8 x .62 Torx/Slot
Washer
Heat Exchanger
Tube - Drain
Cover - Cold Control
Cover - Dispenser Bottom
Screen - VR
Heater Strip
Switch - Rocker
FR Thermostat Assy.
Screw - 8-32 x .38 THTC
Screw - #10 x .75 HHSM
Nut - 1-1/4” Slip Joint
Gasket
Screw - #10-24 x .75 Socket Hd.
Strainer - Bright
Elbow - 5/16” x 1/4”
Torx Tool - T25
Torx Tool - T20
Hanger Bracket
PART NO. DESCRIPTION
*REPLACE WITH SAME COMPRESSOR USED
IN ORIGINAL ASSEMBLY.
NOTE: All correspondence pertaining to any of the
above water coolers or orders for repair parts MUST
include Model No. and Serial No. of cooler, name and
part number of replacement part.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Sold Separate
Sold Separate
NS
ITEM NO.
115V PARTS LIST
*