Emerson Enardo ES-665-HF User manual

Figure 1. Model ES-665-HF Spring-loaded Hatch
Model ES-665-HF High Flow
Spring-Loaded Hatch
WARNING
!
Failure to follow these instructions or to
properly install and maintain this equipment
could result in an explosion, re and/or
chemical contamination causing property
damage and personal injury or death.
Enardo™ spring-loaded hatch
must be installed, operated and
maintained in accordance with federal,
state and local codes, rules and
regulations and Emerson Process
Management Regulator Technologies
Tulsa, LLC instructions.
Failure to correct trouble could result in a
hazardous condition. Call a qualied service
person to service the unit. Installation,
operation and maintenance procedures
performed by unqualied person may
result in improper adjustment and unsafe
operation. Either condition may result in
equipment damage or personal injury. Only
a qualied person shall install or service the
spring-loaded hatch.
Introduction
Scope of the Manual
This Instruction Manual provides instructions for installation,
startup, maintenance and parts ordering information for the
Model ES-665-HF spring-loaded hatch.
Table of Contents
Introduction............................................................................1
Specifications ........................................................................2
Principle of Operation............................................................2
Tagging Information...............................................................2
Installation and Disassembly.................................................2
Maintenance..........................................................................5
Parts Ordering .......................................................................7
Parts List................................................................................7
MODEL ES-665-HF WITH CLOSED HATCH
MODEL ES-665-HF WITH OPEN HATCH
P1806
P1807
Product Description
The Model ES-665-HF high ow gauge hatch is designed
to provide much higher ow rates than standard gauge
hatches, while maintaining the industry leading, tight sealing
performance of the ES-665 Series. It also provides trouble
free operation with maintenance. The primary function of the
Model ES-665-HF high ow hatch is to prevent the loss of
vapors in a closed storage system and provide pressure and
vacuum relief.
Instruction Manual
D104266X012
March 2019
Model ES-665-HF
North America Only

Installation and Disassembly
!
WARNING
Ensure the tank is at atmospheric pressure
before opening. A pressure build-up inside
the tank can cause a spray to be emitted
from the hatch if opened under pressure.
Installing the High Flow
Model ES-665-HF Hatch
1. The Model ES-665-HF hatch can be installed on a
mating ange or roof deck with a standard 8 in. API bolt
pattern (16 – 9/16 in. holes on a 10 – 3/8 in. bolt circle).
For installation of the hatch directly to the tank roof,
place the base gasket on the bottom of the hatch ange
and place on tank roof with bolt holes aligned.
2. Insert the 16 bolts from the bottom up by reaching
inside the tank, through the hatch opening and attach
each nut to the bolt from the outside. Tighten all nuts
in a star pattern (refer to Figure 3) and ensure the
hatch is fastened securely. Refer to Tables 2 and 3 for
torque instructions.
3. For installation of the Model ES-665-HF hatch to a
anged pipe with an 8 in. API ange pattern, simply
place the base gasket on the anged pipe, line up bolt
holes and place hatch on top of base gasket. Install nuts
and bolts and tighten in a star pattern (refer to Figure 3).
Ensure hatch is fastened securely. Refer to Tables 2 and
3 for torque instructions.
The Model ES-665-HF is a spring-loaded hatch with a
round base and cover. It can replace any standard 8 in. API
thief hatch. It has a higher volume of pressure venting than
offered by standard thief hatches and is intended for use
in applications where ultra-tight sealing is required such
as sour crude/gas tanks or where strict environmental
emissions standards are enforced.
Principle of Operation
Enardo gauge hatches are designed to control evaporation
losses and protect tanks against excessive pressure or vacuum.
When the tank pressure is above the setpoint of the hatch, the
cover opens to relieve excess pressure. When the overpressure
has dissipated, the cover reseats onto the base to provide
tight seal.
Tagging Information
The Model ES-665-HF high ow hatch has tagging
information on the spring capsule assembly and on the lid.
Figure 2 shows the typical locations of the tagging
information found on the Model ES-665-HF high ow hatch.
Location 1, on the spring capsule assembly, details the
pressure spring setting and the ow rate for that spring
setting when the tank pressure is at 24 oz./sq. in. Table 1
shows the ow rates at 24 oz./sq. in. for each pressure
spring setting.
Location 2, on the lid, details the vacuum setting and the
date of manufacture.
PRESSURE SETTING, OZ./SQ. IN. FLOW RATE SCFH (AIR) AT 24 OZ./SQ. IN. TANK PRESSURE
6 210,000
8 200,000
12 150,000
16 100,000
Table 1. Pressure Tagging Information
Viton® is a mark owned by E. I. du Pont de Nemours and Company.
Specications
The Specications table lists the specications for the Model ES-665-HF spring-loaded hatch.
Bolt Pattern
8 in. API
Pressure Setting Range(1)
6, 8, 12 and 16 oz./sq. in.
Vacuum Setting Range(1)
0.4, 0.9 and 3.5 oz./sq. in.
Optional Equipment
Base Gasket, Bolt Set and Non-Corrosive Coating
Construction Material
Casting: Aluminum (non-sparking)
Pressure Gasket: HNBR (standard), Viton®
and Fluorosilicone
Vacuum Gasket: Fluorosilicone (standard)
and Viton®
Approximate Shipping Weight
29 lbs / 13.2 kg
1. The pressure/temperature limits in this Instruction Manual and any applicable standard or code limitation should not be exceeded.
2
Model ES-665-HF
North America Only

Figure 2. Tagging Locations
1
5
9
3
8
12
14
2
6
10
15
4
7
11
13
16
NOMINAL PIPE DIAMETER NUMBER OF BOLTS BOLT DIAMETER TORQUE
In. mm Ft-lbs N•m
140.50 12.70 14 18.98
1-1/4 4 0.50 12.70 16 21.69
1-1/2 40.50 12.70 18 24.41
240.63 16.00 32 43.39
2-1/2 40.63 16.00 43 58.30
340.63 16.00 47 63.72
3-1/2 8 0.63 16.00 26 35.25
48 0.63 16.00 32 43.39
6 8 0.75 19.05 49 66.44
8 8 0.75 19.05 68 92.20
10 12 0.88 22.4 69 93.55
12 12 0.88 22.4 98 132.9
14 12 1.00 25.0 138 187.1
16 16 1.00 25.0 125 169.5
18 16 1.13 28.7 142 192.5
2 20 1.13 28.7 135 183.0
24 24 1.25 31.8 156 211.5
8 API 16 0.50 12.70 20 27.12
20 API 16 0.63 16.00 75 101.7
24 API 20 0.63 16.00 75 101.7
Assumptions: Use of SAE grade 5 bolts or studs or stronger
No lubricant
Elastomer <70 Durometer Shore A
Notes: Flat faced anges should never be mated to a raised face ange for installation.
If lubricant is used on bolts, apply torque reduction factor listed in Lubricant Table.
For best results hardened steel washers should be used on all cast ange bolted connections.
Figure 3 High Flow Hatch Torque Sequence
Table 2. Torque Values for Flat Face Flange (Steel or Aluminum)
DESCRIPTION COEFFICIENT OF FRICTION MULTIPLY TORQUE VALUE IN TABLE 2 BY
Machine Oil f = 0.15 0.75
API SA2 Grease f = 0.12 0.60
Nickel-based Lubricant f = 0.11 0.55
Copper-based Lubricant f = 0.10 0.50
Heavy-duty Lubricating Paste f = 0.06 0.30
Table 3. Torque Correction Factors for Common Lubricants Applied on Flanges
3
Model ES-665-HF
North America Only

Figure 4. Side View of Model ES-665-HF
Figure 5. View of Spring Capsule Assembly Screws
2. With the screws loosened enough to remove the spring
capsule assembly, press the spring capsule assembly
down against the spring pressure and rotate. Remove
the spring capsule assembly when the large slot on the
spring capsule assembly is properly aligned with the
bolt head.
Figure 6. Removal of Spring Capsule Assembly
1. Loosen the four (4) bolts that hold the spring capsule
assembly to the lid. The bolts can be loosened
approximately 1/8 in. or enough to allow rotation of the
spring capsule assembly in the machined slots. It is
not necessary to remove the bolts completely, as the
spring capsule assembly is designed with slots to allow
removal without having to remove the bolts.
Note
There will be slight spring pressure that
forces the spring capsule assembly upwards
as the bolts are loosened. This spring
pressure is not great enough to cause
the spring capsule assembly to have a
safety risk.
Accessing Spring Capsule Assembly or
Center Assembly
Note
The Spring Capsule Assembly must
be removed before removing the
Center Assembly.
The Model ES-665-HF Series Center
Assembly can also be installed as a retrot
into an existing Model ES-660-HF by
following the steps outlined in this section.
!
WARNING
Springs are energy storage devices and are
dangerous if handled improperly. Always
use appropriate safety equipment including
safety glasses or shields anytime you are
working with a spring-loaded hatch.
There are times when the spring capsule assembly may
need to be removed (e.g. to change the pressure setting
of the hatch) or to remove the center assembly (e.g. to
change the vacuum setting or to replace the gaskets) from
the Model ES-665-HF hatch. Remove the spring capsule
assembly and the center assembly by following a few
simple steps.
The arrow is pointing to the spring capsule assembly that
houses the pressure spring. The center assembly is not
shown in this view, but is located under the hood.
4
Model ES-665-HF
North America Only

Figure 8. View of Center Assembly
Figure 9. View of Lid Guide Slots
Figure 10. Removal of Center Assembly (Step 1)
Figure 7. Opening High Flow Hatch Lid
Figure 11. Removal of Center Assembly (Step 2)
3. To access the center assembly, press down slightly on
the lid and open the latch.
View of Model ES-665-HF high ow hatch with lid opened.
The arrow is pointing to the center assembly.
The center assembly is guided by slots in the lid.
4. To remove the center assembly, press the center
assembly inward until the center assembly bottoms
out against the inside of the lid, then turn the center
assembly one quarter rotation to the right or left to the
next set of guide slots (see Figure 10). Remove the
center assembly as shown in Figure 11. Be careful not
to drop the pivot pad that rests on top of the center
assembly and provides guidance for the spring capsule
assembly stem.
Maintenance
Perform a scheduled maintenance every three (3) months
and more frequently in corrosive or dusty atmospheres.
Inspect the pressure gaskets and vacuum gaskets for
normal maintenance. To ensure efcient operation of all
hatches, carefully wipe off the pressure and vacuum seats
and gaskets with a clean, non-abrasive, lint-free cloth or
paper towel every time the hatch is opened. This prevents
accumulation of residue that can deteriorate the performance
of the hatches.
Under average operating conditions, replace the pressure
and vacuum gaskets once a year. Replace the base gasket
when a leak is noticed at the bolting area or if the hatch
is removed, breaking the seal. If the hatch is continually
relieving, this is a sign that there is a problem. At that time, a
close inspection should be made to determine the cause.
Note
For parts information refer to the catalog
data sheet on each model. For ease of
part identication, see Figure 16 near the
end of the manual for an exploded view of
Model ES-665-HF high ow hatch.
5
Model ES-665-HF
North America Only

2. The pressure gasket can then be removed and
replaced. The envelope pressure gasket (See Table 4
for pressure gasket options) is enveloped around the
edge of the center assembly. Stretch the old gasket off
and t the new gasket around the circular lip. Ensure
that the bottom side of the pressure gasket is tted
properly in the groove on the bottom of the center
casting. Also ensure that the envelope pressure gasket
is installed squarely and at around the circumference
of the center. See Figure 14 for detailed view of the
pressure gasket and the center.
Vacuum Assembly
1. The vacuum gasket is located between the vacuum
pallet and the seal support on the vacuum assembly. The
vacuum assembly seals against the underside of the center
assembly. To remove the center assembly, rst remove the
spring capsule per Accessing Spring Capsule Assembly
or Center Assembly, steps 1 and 2. Remove the center
assembly under the same section with steps 3 and 4.
2. Once the center assembly is removed, remove the
cotter pin and the conical shaped vacuum spring from
the vacuum stem. Pull the vacuum assembly out from
the bottom side of the center assembly.
3. Remove and replace the vacuum gasket (See Table 5
for vacuum gasket options) from between the vacuum
pallet and the seal support.
4. Reassemble the vacuum assembly, spring and cotter
key in the reverse order of removal. Replace center
assembly into lid (See Section Accessing Spring
Capsule Assembly or Center Assembly and follow
steps 1 through 4 in reverse order). Ensure the pivot
pad is installed at on top of the center assembly before
the spring capsule assembly is attached. See Figure 15
for detailed view of the vacuum assembly.
High Flow (Model ES-665-HF) Hatch
Replacement Parts
Spring Capsule Assembly
!
WARNING
Under no circumstances should the user
attempt to disassemble the spring capsule
assembly. The spring capsule assembly
contains a pre-loaded spring and improper
handling could result in injury.
The spring capsule assembly comes as a pre-assembled
unit. If there is a need to change the pressure setting of the
Model ES-665-HF hatch or to replace an existing spring
capsule assembly, the appropriate spring capsule assembly
can be ordered. Simply follow the instruction in Accessing
Spring Capsule Assembly or Center Assembly steps 2 and 3
in reverse order to install the spring capsule assembly.
Center Assembly
See Figure 13. The center assembly consists of the pressure
gasket, the center casting and the vacuum assembly.
Although not part of the center assembly, the pivot pad is
shown for additional clarity of its relationship to the center
assembly. The pivot pad is not attached to the center
assembly, but rests on top of it to transfer the spring force
from the spring capsule assembly to the center assembly.
Pressure Gasket and Center
1. To remove the center assembly, rst, remove the spring
capsule per Accessing Spring Capsule Assembly or
Center Assembly, steps 1 and 2. Then remove the
center assembly from the same section steps 3 and 4.
Figure 13. Center Assembly Figure 14. Center and Pressure Gasket
Figure 12. Spring Capsule Assembly
6
Model ES-665-HF
North America Only

Parts Ordering
When corresponding with your local Sales Ofce about this
equipment, always reference the equipment serial number
stamped on the nameplate.
When ordering replacement parts, specify the complete
7-character part number of each required part as found in
the following parts list.
Parts List
Vacuum Assembly
Key Description Part Number
1 Vacuum Stem, Aluminum 8568825
2 Flat Washer, 3/8 in., 316 Stainless steel 2012504
3 010 O-ring, Viton®2012710
4 Seal Support, Aluminum 8554636
5 Vacuum Gasket Per order
6 Vacuum Pallet Disk, Aluminum 8559029
7 Hex Nylock Nut, 3/8 in. - 16, 316 Stainless steel 2059201
Model ES-665-HF Hatch
Key Description Part Number
1 Spring Capsule Per order
2 Hex Bolt, 1/4 in. - 20 x 5/8 in.,
316 Stainless steel (4 required) 2035901
3 Center Pad, Aluminum 4557001
4 Latch, Aluminum 4524100
5 #5-C Latch Pin, Zinc-plated Carbon steel 4504103
6 #HPC - 148 Hinge Pin Clip,
Zinc-plated Carbon steel (2 required) 2027100
7 Lid, Aluminum 4522001
8 #70 Envelope Gasket Per order
9 Cotter Pin, 1/8 x 1 in., 304 Stainless steel 2022101
10 Vacuum Stem, Aluminum 8568825
11 Vacuum Spring Per order
12 Center, Aluminum 4556002
13 Flat Washer, 3/8 in., 316 Stainless steel 2012504
14 010 O-ring, Viton®2012710
15 Seal Support, Aluminum 8554636
16 Vacuum Gasket Per order
17 Vacuum Pallet Disk, Aluminum 8559029
18 Hinge Spring, 302 Stainless steel 4504005
19 Clevis Pin, 5/6 x 2 1/2 in., Zinc-plated Carbon steel 4505110
20 Hex Nylock Nut, 3/8 in. - 16, 316 Stainless steel 2059201
21 Base, Aluminum 4507303
22 Cotter Pin, 1/8 x 1/2 in.,
304 Stainless steel (2 required) 2000703
23 Clevis Pin, 5/16 x 3 1/2 in., Zinc-plated Carbon steel 4505112
Viton® is a mark owned by E. I. du Pont de Nemours and Company.
Inconel® is a mark owned by Special Metals Corporation.
SETTING, OZ./SQ. IN. MATERIAL COLOR 1 COLOR 2 PART NUMBER
0.4 H.D. Steel (Galvanized) Light Blue Light Blue 4503700
0.9 Drawn CS Wire (Galvanized) Gray Gray 4504100
3.5 H.D. Steel (Galvanized) Yellow Yellow 4503900
0.4 Inconel®Light Blue White 4503800
0.9 Inconel®Gray White 4504200
Table 7. Vacuum Spring Options
SETTING, OZ./SQ. IN. PART NUMBER
64556201
84556202
12 4556203
16 4556204
Table 6. Spring Capsule Options
MATERIAL PART NUMBER
HNBR (Standard) 4504601
Viton®4504603
Fluorosilicone 4504605
MATERIAL PART NUMBER
Fluorosilicone (Standard) 4504705
Viton®4504708
Table 4. Pressure (Envelope) Gasket Options
Table 5. Vacuum Gasket Options
7
Model ES-665-HF
North America Only

Figure 15. Vacuum Assembly Figure 16. Model ES-665-HF High Flow Hatch
Exploded View
1
3
5
6
7
4
2
PALLET DISK GROOVE SIDE UP
Model ES-665-HF
Facebook.com/EmersonAutomationSolutions
LinkedIn.com/company/emerson-automation-solutions
Twitter.com/emr_automation
[email protected]
Enardo.com
D104266X012 © 2019 Emerson Process Management Regulator
Technologies, Inc. All rights reserved. 03/19.
The Emerson logo is a trademark and service mark of Emerson
Electric Co. All other marks are the property of their prospective owners.
Enardo™ is a mark owned by Regulator Technologies Tulsa, LLC, a
business of Emerson Automation Solutions.
The contents of this publication are presented for informational purposes
only, and while every effort has been made to ensure their accuracy,
they are not to be construed as warranties or guarantees, express or
implied, regarding the products or services described herein or their use
or applicability. We reserve the right to modify or improve the designs or
specications of such products at any time without notice.
Emerson Process Management Regulator Technologies
Tulsa, LLC does not assume responsibility for the selection, use or
maintenance of any product. Responsibility for proper selection, use
and maintenance of any Emerson Process Management Regulator
Technologies Tulsa, LLC product remains solely with the purchaser.
North America Only
Emerson Automation Solutions
Americas
McKinney, Texas 75070 USA
T [phone]
[phone]
Tulsa, OK 74146 USA
T [phone]
Europe
Bologna 40013, Italy
T [phone]
Asia Pacic
Singapore 128461, Singapore
T [phone]
Middle East and Africa
Dubai, United Arab Emirates
T [phone]