Emerson Bettis RP3E User manual

Bettis RTS Relay Board (RP3E)
Electric Actuator
Installation, Operation and Maintenance Manual
VCIOM-15746-EN Rev. 1
April 2023

Note
April 2023
Installation, Operation and Maintenance Manual
VCIOM-15746-EN Rev. 1
This page intentionally left blank.

i
Installation, Operation and Maintenance Manual
VCIOM-15746-EN Rev. 1
Table of Contents
April 2023
Table of Contents
Table of Contents
Section 1: Tools
Tools.........................................................................................................................1
Section 2: Material
Material.....................................................................................................................2
Section 3: Installation
Installation................................................................................................................3
Section 4: Programming
Programming............................................................................................................8

Note
April 2023
Installation, Operation and Maintenance Manual
VCIOM-15746-EN Rev. 1
This page intentionally left blank.

Installation, Operation and Maintenance Manual
VCIOM-15746-EN Rev. 1 April 2023
Tools 1
Section 1: Tools
Section 1: Tools
! WARNING
Remove all power supplies before doing the exchange. Always act with caution during
the exchange!
• Needle nose pliers
• Screw driver phillips
• Screw driver at
• Allen key 5
• Socket wrench 5
Figure 1.

April 2023
Installation, Operation and Maintenance Manual
VCIOM-15746-EN Rev. 1
Material
2
Section 2: Material
Section 2: Material
• 1x relay board RP3E6A (ID:13009)
• 1x adapter cable (ID:16504)
• 2x steel screw M3x16 (ID:952)
• 3x plastic distance 8 mm (ID:9896)
• 1x plastic screw M3x15 (ID:9895)
• 1x plastic nut M3 (ID:7084)
• 2x lock plates M3 red (ID:13674)
Figure 2.
Figure 3.

Installation, Operation and Maintenance Manual
VCIOM-15746-EN Rev. 1 April 2023
Installation 3
Section 3: Installation
Section 3: Installation
Unscrew the 4 hexagon socket screws from the cover and remove it carefully. Mind the
connection cable between display and logic board.
Figure 4.
Unscrew the 4 cross recessed screws from the existing logic board and afterwards, tilt it
carefully to you.
Figure 5.

April 2023
Installation, Operation and Maintenance Manual
VCIOM-15746-EN Rev. 1
Installation4
Section 3: Installation
Remove carefully the connected cables: ribbon cable and 6-, 8- and 10-pole plugs
(see Figure 6, left image). Afterwards, you can remove the logic board from the control
unit and disconnect the second ribbon cable on the back (see Figure 6, right image).
Figure 6.
Remove the two steel spacers (marked with the black arrows in Figure 7) in the housing.
Figure 7.

Installation, Operation and Maintenance Manual
VCIOM-15746-EN Rev. 1 April 2023
Installation 5
Section 3: Installation
Place the 8 mm plastic spacers on the relay board as shown in the top image of Figure 8.
Insert the M3x16 steel screws through the holes next to the multi-pin connectors in the
logic board as shown in the bottom image of Figure 8. Then line up the screws with the
plastic spacers in the relay board and secure the screws with the red lock plates. For the
third hole, use the plastic screw M3x15 and secure it in place with the plastic nut.
Figure 8.
Connect the relay board with the multi-pin connector from the logic board.
! WARNING
The four pins on the left side must remain disconnected (see Figure 9).
The orientation of the mounting holes on both the logic and relay boards plus the spacers
must be aligned as shown in Figure 9.
Figure 9.

April 2023
Installation, Operation and Maintenance Manual
VCIOM-15746-EN Rev. 1
Installation6
Section 3: Installation
Connect the 10- and 6-pole connectors to the adapter cables, then connect the blue
connectors of the adapter cables to the corresponding connectors on the relay board.
Figure 10.