Emerson Fisher FIELDVUE DVC6200 SIS Configuration guide

www.Fisher.com
ATEX Hazardous Area Approvals
Fisher™FIELDVUE™DVC6200 Series
Digital Valve Controllers
Hazardous Area Approvals and Special Instructions
for “Safe Use” and Installations in Hazardous Locations
Certain nameplates may carry more than one approval, and each approval may have unique installation/wiring
requirements and/or conditions of “safe use”. These special instructions for “safe use” are in addition to, and may
override, the standard installation procedures. Special instructions are listed by approval type.
Note
This information supplements the nameplate markings affixed to the product and the DVC6200 Series quick start guide
(D103556X012), available from your Emerson sales office or at Fisher.com.
Always refer to the nameplate itself to identify the appropriate certification.
Approval information is for both aluminum and stainless steel constructions.
WARNING
Failure to follow these conditions of “safe use” could result in personal injury or property damage from fire or explosion
and area re‐classification.
WARNING
To avoid static discharge from the plastic cover when flammable gases or dust are present, do not rub or clean the cover
with solvents. To do so could result in a spark that may cause the flammable gases or dust to explode, resulting in personal
injury or property damage. Clean with a mild detergent and water only.
Instruction Manual Supplement
D104205X012
DVC6200 Digital Valve Controllers
November 2020
SIS

Instruction Manual Supplement
D104205X012
DVC6200 Digital Valve Controllers
November 2020
2
Flameproof II 2 G
WARNING
Do not open while energized.
Potential electrostatic charging hazard. See warning on page 1.
Covered by Standards:
EN 60079-0:2012 + A11:2013
EN 60079-1:2014
DVC6200 and DVC6205 Series (HART HW1 & HW2, SIS, FOUNDATION Fieldbus, PROFIBUS)
Ex d IIC T5 (Ta ≤ 80°C) / T6 (Ta ≤ 75°C) Gb
Operating ambient temperature
Standard construction -40_C to +80_C,
Extreme temperature construction -52_C to +80_C
DVC6215
Ex d IIC T4 (Ta ≤ 125°C) / T5 (Ta ≤ 95°C) / T6 (Ta ≤ 80°C) Gb
Operating ambient temperature
-52_C to +125°C

Instruction Manual Supplement
D104205X012
DVC6200 Digital Valve Controllers
November 2020
3
Type n II 3 G
WARNING
Do not open while energized.
Potential electrostatic charging hazard. See warning on page 1.
Covered by Standards:
EN 60079-0:2012 + A11:2013
EN 60079-15:2010
DVC6200 and DVC6205 Series (HART HW1 & HW2, SIS, FOUNDATION Fieldbus, PROFIBUS)
Ex nC IIC T5 (Ta ≤ 80°C) / T6 (Ta ≤ 75°C) Gc
Operating ambient temperature
Standard construction -40_C to +80_C,
Extreme temperature construction -52_C to +80_C
DVC6215
Ex nA IIC T4 (Ta ≤ 125°C) / T5 (Ta ≤ 95°C) / T6 (Ta ≤ 80°C) Gc
Operating ambient temperature
-52_C to +125°C

Instruction Manual Supplement
D104205X012
DVC6200 Digital Valve Controllers
November 2020
4
Intrinsically Safe
WARNING
Potential electrostatic charging hazard. See warning on page 1.
Covered by Standards:
EN 60079-0:2012 + A11:2013
EN 6007911:2012
DVC6200 and DVC6205 Series (HART HW1 & HW2, SIS, FOUNDATION Fieldbus, PROFIBUS)
II 1 GD
Ex ia IIC or IIB T4/T5/T6 Ga (see figure 1 to 5)
Ex ia IIIC Txxx°C Da (see figure 1 to 5)
Operating ambient temperature
Standard construction -40_C to +80_C,
Extreme temperature construction -52_C to +80_C
DVC6215
II 1 G
Ex ia IIC T4/T5/T6 Ga (see figure 2 and 4)
Operating ambient temperature
- 52_C≤ Ta ≤+ 125_C
Intrinsically safe when connected per control drawing GE60771, as shown in the following figures
DVC6200 HW2, DVC6200 SIS figure 1 and 6...............................
DVC6205, DVC6205 SIS, and DVC6215 Remote Mount figure 2 and 6........
DVC6200f and DVC6200p figure 3 and 6..................................
DVC6205f, DVC6205p, and DVC6215 Remote Mount figure 4 and 6..........
DVC6200 HW1 figure 5 and 6...........................................
Special Conditions for Safe Use; Intrinsically Safe Applications
D This apparatus can only be connected to an intrinsically safe certified equipment and this combination must be
compatible as regards the intrinsically safe rules.
D For the model with aluminum body: the apparatus must not be submitted to frictions or mechanical impacts.

Instruction Manual Supplement
D104205X012
DVC6200 Digital Valve Controllers
November 2020
5
Figure 1. ATEX Loop Schematics—FIELDVUE DVC6200 HW2 and DVC6200 SIS
Ui = 30 VDC
Ii = 130 mA
Pi = 1.0 W
Ci = 15 nF
Li = 0.15 mH
LOOP TERMINALS
AUX TERMINALS
LOOP TERMINALS
Ex ia IIC
LOOP TERMINALS
Ex ia IIB
Ui = 30 VDC
Ii = 101 mA
Pi = 757 mW
Ci = 15 nF
Li = 0.30 mH
Ui = 27.1 VDC
Ii = 130 mA
Pi = 880 mW
Ci = 15 nF
Li = 0.30 mH
Ui = 30 VDC
Ii = 130 mA
Pi = 1.0 W
Ci = 15 nF
Li = 0.30 mH
Uo = 30 VDC
Io = 101 mA
Po = 757 mW
Co = 52.4 nF
Lo = 5.84 mH
Not Used or
Not Provided
AUX TERMINALS
Uo = 27.1 VDC
Io = 130 mA
Po = 880 mW
Co = 75 nF
Lo = 2.73 mH
AUX TERMINALS
Uo = 30 VDC
Io = 130 mA
Po = 1.0 W
Co = 546 nF
Lo = 16.93 mH
HW2 - WITH OR WITHOUT I/O PACKAGE
DVC6200, DVC6200S
AUX TERMINALS
LOOP TERMINALS
Ex ia IIC
Ui = 28 VDC
Ii = 100 mA
Pi = 1.0 W
Ci = 15 nF
Li = 0.20 mH
OUTPUT TERMINALS
Ex ia IIC or Ex ia IIB
ATEX APPROVED
BARRIER
ATEX APPROVED
BARRIER
NOTE 5 1
NOTE 1, 3, 4 1
NOTE 1, 3, 4 1
POWER MAY BE APPLIED TO EITHER THE LOOP
TERMINALS OR OUTPUT TERMINALS OR TO
BOTH SETS OF TERMINALS AT THE SAME TIME
UNITS WITHOUT I/O PACKAGE WILL NOT HAVE
“OUTPUT TERMINALS” OR “AUX TERMINALS”
AVAILABLE FOR CONNECTION
ZONE 0, Ex ia IIC or Ex ia IIB
DVC6200
DVC6200S
ZONE 20, Ex ia IIIC
MAX
SURFACE
TEMP
T91_C
T85_C
T AMB
≤80_C
≤74_C
T AMB
≤80_C
≤74_C
T CODE
T5
T6
TYPE
WITH I/O
PACKAGE
WITH I/O
PACKAGE
WITHOUT I/O
PACKAGE
WITHOUT I/O
PACKAGE
T AMB
≤80_C
≤61_C
T CODE
T5
T6
MAX
SURFACE
TEMP
T104_C
T85_C
T AMB
≤80_C
≤61_C
ZONE 0, Ex ia IIC
ZONE 0, Ex ia IIB
ZONE 20, Ex ia IIIC HAZARDOUS LOCATION NON‐HAZARDOUS LOCATION
1 SEE NOTES IN FIGURE 6
GE60771 Sheet 11, Rev. D
*Li = 0.15 mH WHEN THE AUX
TERMINALS ARE NOT USED OR IF
THEY ARE NOT PROVIDED
*

Instruction Manual Supplement
D104205X012
DVC6200 Digital Valve Controllers
November 2020
6
Figure 2. ATEX Loop Schematics—FIELDVUE DVC6205, DVC6205 SIS, and DVC6215
1 SEE NOTES IN FIGURE 6
GE60771 Sheet 12 Rev. D
AUX TERMINALS
Not Used or
Not Provided
Uo = 30 VDC
Io = 21.2 mA
Po = 160 mW
Co = 55 nF
Lo = 78 mH
Ui = 30 VDC
Ii = 226 mA
Pi = 1.4 W
Ci = 50 nF
Li= 0.55 mH
AUX TERMINALS
ZONE 0, Ex ia IIC ZONE 0, Ex ia IIB ZONE 20, Ex ia IIIC
Ui = 30 VDC
Ii = 130 mA
Pi = 1.0 W
Ci = 15 nF
Li = 0.15 mH
NOTE 1, 3 1
DVC6215
ZONE 0, Ex ia IIC
REMOTE FIELD WIRING
TERMINAL BOX
Uo = 30 VDC
Io = 101 mA
Po = 757 mW
Co = 52.4 nF
Lo = 5.84 mH
Ui = 30 VDC
Ii = 101 mA
Pi = 757 mW
Ci = 15 nF
Li = 0.30 mH
T CODE
T4
T5
T6
T AMB
≤125_C
≤95_C
≤80_C
ZONE 0, Ex ia IIC
DVC6215
Ex ia IIC or Ex ia IIB
TERMINALS
Ex ia IIC
LOOP TERMINALS
Ex ia IIC
LOOP TERMINALS
*Li = 0.15 mH WHEN THE AUX
TERMINALS ARE NOT USED OR IF
THEY ARE NOT PROVIDED
*
ZONE 0, Ex ia IIC or Ex ia IIB
DVC6205
ZONE 20, Ex ia IIIC
MAX
SURFACE
TEMP
T91_C
T85_C
T AMB
≤80_C
≤74_C
T AMB
≤80_C
≤74_C
T CODE
T5
T6
TYPE
WITH I/O
PACKAGE
WITH I/O
PACKAGE
WITHOUT I/O
PACKAGE
WITHOUT I/O
PACKAGE
T AMB
≤80_C
≤61_C
T CODE
T5
T6
T AMB
≤80_C
≤61_C
MAX
SURFACE
TEMP
T104_C
T85_C
HW2 - WITH OR WITHOUT I/O PACKAGE
DVC6205
FIELD WIRING
TERMINAL BOX

Instruction Manual Supplement
D104205X012
DVC6200 Digital Valve Controllers
November 2020
7
Ui = 27.1 VDC
Ii = 130 mA
Pi = 880 mW
Ci = 15 nF
Li = 0.30 mH
AUX TERMINALS AUX TERMINALS
Uo = 27.1 VDC
Io = 130 mA
Po = 880 mW
Co = 75 nF
Lo = 2.73 mH
ATEX APPROVED BARRIER
HAZARDOUS LOCATION NON‐HAZARDOUS LOCATION
NOTE 5
1
NOTE 1, 3, 4 1
Ex ia IIC
LOOP TERMINALS
Ex ia IIB
LOOP TERMINALS
Ui = 30 VDC
Ii = 130 mA
Pi = 1.0 W
Ci = 15 nF
Li = 0.30 mH
Uo = 30 VDC
Io = 130 mA
Po = 1.0 W
Co = 546 nF
Lo = 16.93 mH
Ex ia IIC or Ex ia IIB
OUPUT TERMINALS
Ui = 28 VDC
Ii = 100 mA
Pi = 1.0 W
Ci = 15 nF
Li = 0.20 mH
ATEX APPROVED BARRIER
NOTE 1, 3, 4 1
POWER MAY BE APPLIED TO EITHER THE LOOP
TERMINALS OR OUTPUT TERMINALS OR TO
BOTH SETS OF TERMINALS AT THE SAME TIME
UNITS WITHOUT I/O PACKAGE WILL NOT HAVE
“OUTPUT TERMINALS” OR “AUX TERMINALS”
AVAILABLE FOR CONNECTION

Instruction Manual Supplement
D104205X012
DVC6200 Digital Valve Controllers
November 2020
8
1 SEE NOTES IN FIGURE 6
FISCO LOOP
ENTITY FIELDBUS LOOP
GE60771 Sheet 5, Rev D.
1 NOTE 5
NON‐HAZARDOUS LOCATION
ZONE 0, Ex ia IIC
ZONE 20, Ex ia IIIC
LOOP TERMINALS
Ui = 24 VDC
Ii = 380 mA
Ci = 5 nF
Li = 0 mH
Pi = 1.4 W
HAZARDOUS LOCATION
ATEX APPROVED
BARRIER
HAZARDOUS LOCATION NON‐HAZARDOUS LOCATION
ATEX APPROVED
FISCO BARRIER
ATEX APPROVED
FISCO TERMINATOR
ATEX
APPROVED
FISCO DEVICE
LOOP TERMINALS
Ui = 17.5 VDC
Ii = 380 mA
Ci = 5 nF
Li = 0 mH
Pi = 5.32 W
ATEX
APPROVED
ENTITY DEVICE
NOTE 1, 3 1
1 NOTE 1, 3, 4
1 NOTE 2, 3, 4
NOTE 2, 3 1
Figure 3. ATEX Loop Schematics—FIELDVUE DVC6200f and DVC6200p
ZONE 0
Ex ia IIC
ZONE 20
Ex ia IIIC
ZONE 0, Ex ia IIC
ZONE 20, Ex ia IIIC
GE60771 Sheet 4, Rev. D
DVC6200F, DVC6200FS
DVC6200P, DVC6200PS
DVC6200F, DVC6200FS
DVC6200P, DVC6200PS
T CODE
T4
T5
T6
T AMB
≤80_C
≤77_C
≤62_C
MAX
SURFACE
TEMP
T103_C
T100_C
T85_C
T AMB
≤80_C
≤77_C
≤62_C
ZONE 0
Ex ia IIC
ZONE 20
Ex ia IIIC
T CODE
T4
T5
T6
T AMB
≤80_C
≤77_C
≤62_C
MAX
SURFACE
TEMP
T103_C
T100_C
T85_C
T AMB
≤80_C
≤77_C
≤62_C
1 SEE NOTES IN FIGURE 6

Instruction Manual Supplement
D104205X012
DVC6200 Digital Valve Controllers
November 2020
9
T CODE
T4
T5
T6
1 SEE NOTES IN FIGURE 6
ATEX
APPROVED
ENTITY
DEVICE
HAZARDOUS LOCATION
NON‐HAZARDOUS LOCATION
ZONE 0, Ex ia IIC
Ui = 30 VDC
Ii = 226 mA
Ci = 50 nF
Li = 0.55 mH
Pi = 1.4 W
ATEX APPROVED
BARRIER
NON‐HAZARDOUS LOCATION
HAZARDOUS LOCATION
ENTITY FIELDBUS LOOP
ATEX
APPROVED
FISCO BARRIER
ATEX APPROVED
FISCO
TERMINATOR
ATEX
APPROVED
FISCO DEVICE
FISCO LOOP
1 NOTE 1, 3, 4
NOTE 1, 3 1
NOTE 5 1
1 NOTE 2, 3, 4
NOTE 2, 3 1
GE42818 Sheet 10, Rev. D
Figure 4. ATEX Loop Schematics—FIELDVUE DVC6205f, DVC6205p, and DVC6215
NOTE 1, 3 1
Uo = 24 VDC
Io = 44 mA
Co = 121 nF
Lo = 30 mH
Po = 0.33 W
Ui = 24 VDC
Ii = 380 mA
Ci = 5 nF
Li = 0 mH
Pi = 1.4 W
DVC6215
NOTE 2 1
ZONE 0, Ex ia IIC
ZONE 20, Ex ia IIIC
ZONE 0, Ex ia IIC ZONE 20, Ex ia IIIC
ZONE 0, Ex ia IIC
DVC6205f
DVC6205p
TYPE
DVC6215
ZONE 0, Ex ia IIC ZONE 20, Ex ia IIIC
ZONE 0, Ex ia IIC
DVC6205f
DVC6205p
TYPE
DVC6215
DVC6215
GE42818 Sheet 9, Rev. D
T AMB
----
≤125_C
≤95_C
≤80_C
T CODE
----
T4
T5
T6
T AMB
≤80_C
≤77_C
≤62_C
MAX
SURFACE
TEMP
T103_C
T100_C
T85_C
T AMB
≤80_C
≤77_C
≤62_C
T AMB
----
≤125_C
≤95_C
≤80_C
T CODE
----
T4
T5
T6
T AMB
≤80_C
≤77_C
≤62_C
MAX
SURFACE
TEMP
T103_C
T100_C
T85_C
T AMB
≤80_C
≤77_C
≤62_C
T CODE
T4
T5
T6
LOOP
TERMINALS
DVC6205f, DVC6205p
TERMINALS
REMOTE FIELD
WIRING TERMINAL
BOX
FIELD WIRING
TERMINAL BOX
REMOTE FIELD WIRING
TERMINAL BOX
FIELD WIRING
TERMINAL BOX
LOOP
TERMINALS
TERMINALS
ZONE 0, Ex ia IIC
Uo = 17.5 VDC
Io = 44 mA
Co = 121 nF
Lo = 30 mH
Po = 0.33 W
Ui = 17.5 VDC
Ii = 380 mA
Ci = 5 nF
Li = 0 mH
Pi = 5.32 W
ZONE 0, Ex ia IIC
ZONE 20, Ex ia IIIC
DVC6205f, DVC6205p
Ui = 30 VDC
Ii = 226 mA
Ci = 50 nF
Li = 0.55 mH
Pi = 1.4 W
1 SEE NOTES IN FIGURE 6

Instruction Manual Supplement
D104205X012
DVC6200 Digital Valve Controllers
November 2020
10
Ui = 30 VDC
Ii = 226 mA
Pi = 1.4 W
Ci = 5 nF
Li = 0.55 mH
ZONE 0, Ex ia IIC
ZONE 0, Ex ia IIB
ZONE 20, Ex ia IIIC
LOOP TERMINALS
AUX TERMINALS
Ex ia IIC
LOOP TERMINALS
Ex ia IIC
LOOP TERMINALS
Ex ia IIC
LOOP TERMINALS
Ex ia IIB
Ui = 30 VDC
Ii = 101 mA
Pi = 757 mW
Ci = 5 nF
Li = 0.55 mH
Ui = 24.3 VDC
Ii = 169 mA
Pi = 1.026 W
Ci = 5 nF
Li = 0.55 mH
Ui = 30 VDC
Ii = 226 mA
Pi = 1.4 W
Ci = 5 nF
Li = 0.55 mH
Uo = 30 VDC
Io = 101 mA
Po = 757 mW
Co = 64 nF
Lo = 5.34 mH
Not Used
AUX TERMINALS
Uo = 24.3 VDC
Io = 169 mA
Po = 1.026 W
Co = 118 nF
Lo = 0.30 mH
AUX TERMINALS
Uo = 30 VDC
Io = 226 mA
Po = 1.4 W
Co = 558 nF
Lo = 3.76 mH
DVC6200, DVC6200S
ATEX APPROVED BARRIER
NOTE 1, 3, 4 1
NOTE 5 1
AUX TERMINALS
HAZARDOUS LOCATION NON‐HAZARDOUS LOCATION
Figure 5. ATEX Loop Schematic—FIELDVUE DVC6200 HW1
ZONE 0
Ex ia IIC or Ex ia IIB
DVC6200
DVC6200S
ZONE 20
Ex ia IIIC
MAX
SURFACE
TEMP
T89_C
T85_C
T AMB
≤80_C
≤76_C
T AMB
≤80_C
≤75_C
T CODE
T5
T6
TYPE
1 SEE NOTES IN FIGURE 6
GE60771 Sheet 3, Rev. D