Emerson CASH A-401 Manual

Before installation, these instructions must be read carefully and understood.
CASH TYPE A-401 CRYOGENIC PRESSURE REGULATOR
INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
Emerson.com/FinalControl © 2018 Emerson. All rights reserved. VCIOM-10805-EN 20/08
DESCRIPTION
The Type A-401 regulator is a fully automatic
pressure regulating valve designed for
cryogenic service in the pressure build-up
circuit. Because it may be used for either
cryogenic liquids or gases, it may be installed
either before or after the pressure build-up
coil.
SPECIFICATION DATA
Service: Cryogenic liquids and gases
(pressure reducing or pressure build-up
service)
Sizes: ½"
Connections: Threaded internal inlet
and outlet.
Body Material: Bronze
Temperature Rating:
-320°F (-195.5°C) to +150°F (65.5°C)
Maximum Initial Pressure: 600 psig (41.4 bar)
INSTALLATION INSTRUCTIONS
The Type A-401 regulator should be installed in
the horizontal position with the spring chamber
upright or down. Install a Y-Type or equivalent
strainer upstream of the Type A-401. For
other installation requirements, consult the
factory. For easy operation and maintenance,
it is suggested that manual shut-off valves be
installed upstream and downstream from the
valve. Before installing the valve, the piping
and valve should be thoroughly flushed out
to remove any foreign material. In order to
prevent contamination from entering the valve,
an in-line screen is recommended. Install
the valve with the inlet pipe fitted to the inlet
connection identified on the valve body. Use a
compatible sealant on the male pipe threads
and do not over-tighten the valve connections.
CONSTRUCTION
See component description for materials of
construction.
All parts are commercially cleaned for oxygen
service.
OPERATING INSTRUCTIONS
Adjusting the Delivery Pressure
The regulator’s delivery pressure setting is
adjusted by turning the adjusting screw (1)
at the top of the spring chamber (3) after
loosening the adjusting screw lock nut (2).
To increase the delivery pressure, turn the
adjusting screw clockwise (into the spring
chamber). To decrease the delivery pressure,
turn the adjusting screw counter-clockwise (out
of the spring chamber). Tighten the adjusting
screw lock nut after the adjustment has been
made (and reinstall optional cap).
MAINTENANCE INSTRUCTIONS
CAUTION
Before attempting to replace any spare parts,
be sure to shut off all pressure connections to
the valve. With the valve closed however, system
pressure could still be locked between the shut
off valve and the inlet and/or outlet sides of the
regulator. Before proceeding with any valve
service, be certain to relieve the pressure from
both sides of the regulator.
After reassembly and before pressurizing the
valve, tighten the adjusting screw to ensure there
is force on the pressure plate. This will help avoid
damage to parts that will cause the valve to leak
and not function correctly.
Refer to section view on the following page for
parts identification. Repair parts can easily be
installed without removing the regulator from the
line.

2
CASH TYPE A-401 CRYOGENIC PRESSURE REGULATOR
INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
Item Quantity Description Material
1 1 Adjusting Screw SST
2 1 Lock Nut SST
3 1 Spring Chamber Bronze
4 1 Spring Button Brass
5 1 Name Plate Aluminum
6 2 Drive Screw SST
7 1 Pressure Spring SST
8 1 Diaphragm Stop Brass
9 1 Gasket Teflon
10 1Diaphragm Sub - - - -
10a 1Nut SST
10b 1Washer SST
10c 1Pressure Plate Brass
10d 4Diaphragm Bronze
10e 1Gasket Teflon
10f 1P-Post Button SST
11 1Piston Sub - - - -
11a 1Piston Brass
11b 1Seat Disc Teflon
12 1Spring SST
13 1Gasket Gylon
14 1Bottom Plug Brass
15 4Screw SST
16 1Body Bronze
BILL OF MATERIALS
INLET OUTLET
FIGURE 1
VCIOM-10805 © 2018, 2020 Emerson Electric Co. All rights reserved 08/20. Cash Valve is a mark owned by one of the companies in the Emerson Automation
Solutions business unit of Emerson Electric Co. The Emerson logo is a trademark and service mark of Emerson Electric Co. All other marks are the property of their
prospective owners.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be
construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. All sales are governed
by our terms and conditions, which are available upon request. We reserve the right to modify or improve the designs or specifications of such products at any time
without notice.
Emerson Electric Co. does not assume responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use and maintenance
of any Emerson Electric Co. product remains solely with the purchaser.
Emerson.com/FinalControl