Emerson DIXELL XR30T Wiring diagram

Full Touch
XR30T - XR60T – XR70T
(V.1.3)

1592040000 XR30-60-70T EN v1.3 2020.08.26 XR30-60-70T 3/40
INDEX
1. IMPORTANT USER INFORMATION..............................................................................................................................................................................5
2. PRODUCT DISPOSAL (WEEE).......................................................................................................................................................................................6
3. GENERALITIES.............................................................................................................................................................................................................7
3.1 USEFULINFORMATION.....................................................................................................................................................................................7
4. USER INTERFACE.........................................................................................................................................................................................................7
4.1 SCREENS............................................................................................................................................................................................................7
4.2 ICONS................................................................................................................................................................................................................8
4.3 GESTURES.......................................................................................................................................................................................................10
4.4 HOMEBROWSING ..........................................................................................................................................................................................10
4.5 STAND-BY MODE............................................................................................................................................................................................10
4.6 PROGRAMMINGMENU..................................................................................................................................................................................10
4.7 SETPOINT MENU.............................................................................................................................................................................................11
4.8 HOTKEY–UPLOAD..........................................................................................................................................................................................11
4.9 HOTKEY–DOWNLOAD...................................................................................................................................................................................11
4.10 X9....................................................................................................................................................................................................................11
4.11 PARAMETERMENU.........................................................................................................................................................................................12
4.12 PASSWORDMENU..........................................................................................................................................................................................13
5. PARAMETER TABLE...................................................................................................................................................................................................13
5.1 PARAMETERDESCRIPTION.............................................................................................................................................................................13
5.1.1 Main regulation parameters - rEG.............................................................................................................................................................13
5.1.2 Probeconfiguration parameters – Prb......................................................................................................................................................14
5.1.3 Visualization parameters- diS...................................................................................................................................................................14
5.1.4 Defrost configuration parameters - dEF....................................................................................................................................................14
5.1.5 Evaporator and condenser fan configuration parameters - FAn...............................................................................................................15
5.1.6 Auxiliary regulator parameters - AUS........................................................................................................................................................16
5.1.7 Alarmconfiguration parameters...............................................................................................................................................................16
5.1.8 Digital and analogue output configuration parameters - out...................................................................................................................17
5.1.9 Digital input configuration parameters - inP.............................................................................................................................................17
5.1.10 Energy saving configuration parameters - ES.......................................................................................................................................18
5.1.11 Counters, read only values - Cnt...........................................................................................................................................................18
5.1.12 Real Time Clock configuration parameters - rtC...................................................................................................................................18
5.1.13 Memory storage management – E2.....................................................................................................................................................19
5.1.14 Serial Communication port configuration parameters - CoM..............................................................................................................19
5.1.15 User Interface configuration parameters - Ui ......................................................................................................................................19
5.1.16 Information, read only parameters- inF ..............................................................................................................................................19
5.2 PARAMETERCONFIGURATION1....................................................................................................................................................................20
5.3 PARAMETERCONFIGURATION2....................................................................................................................................................................26
6. REGULATION.............................................................................................................................................................................................................31
7. ENERGY SAVING........................................................................................................................................................................................................31
7.1 BASICENERGYSAVINGALGORITHM...............................................................................................................................................................31
7.1.1 PARAMETERS INVOLVED...........................................................................................................................................................................31
8. PULL DOWN FUNCTION............................................................................................................................................................................................32
9. DEFROST OPERATIONS.............................................................................................................................................................................................32
9.1 TIMEDORTEMPERATURECONTROLLEDMODE.............................................................................................................................................32
10. EVAPORATORFAN...............................................................................................................................................................................................32
10.1 EVAPORATORFANANDDIGITALINPUT..........................................................................................................................................................32
11. CONDENSER FAN.................................................................................................................................................................................................33
12. DIGITAL OUTPUTS................................................................................................................................................................................................33
12.1 COMPRESSOROUTPUT (OAX =CP1)................................................................................................................................................................33
12.2 DEFROST OUTPUT(OAX =DEF)........................................................................................................................................................................33
12.3 EVAPORATORFAN OUTPUT(OAX =FAN).........................................................................................................................................................33
12.4 ALARMOUTPUT (OAX =ALR)...........................................................................................................................................................................33
12.5 LIGHTOUTPUT (OAX =LIG)..............................................................................................................................................................................33
12.6 AUXILIARY OUTPUT(OAX =AUS).....................................................................................................................................................................33
12.6.1 AUXILIARY REGULATOR........................................................................................................................................................................33
12.6.2 TIMED ACTIVATION..............................................................................................................................................................................33
12.6.3 GENERAL NOTES...................................................................................................................................................................................34
12.7 DEADBANDREGULATION(OAX =DB)..............................................................................................................................................................34
12.8 ON/OFFOUTPUT(OAX =ONF)..........................................................................................................................................................................34
12.9 ENERGYSAVINGOUTPUT(OAX =HES)............................................................................................................................................................34
12.10 CONDENSERFANOUTPUT(OAX =CND)...........................................................................................................................................................34
12.11 SECONDCOMPRESSOROUTPUT(OAX =CP2).................................................................................................................................................34
12.12 SECONDDEFROSTOUTPUT(OAX =DF2)..........................................................................................................................................................34
12.13 HEATEROUTPUT(OAX =HET)..........................................................................................................................................................................34
12.14 INVERTEROUTPUT(OAX =INV)........................................................................................................................................................................34
13. DIGITAL INPUTS...................................................................................................................................................................................................34
13.1 DOORSWITCH (IXF=DOR).................................................................................................................................................................................34
13.2 STARTDEFROST(IXF=DEF)...............................................................................................................................................................................35
13.3 AUXILIARY OUTPUT(IXF=AUS)........................................................................................................................................................................35
13.4 ENERGYSAVING(IXF=ES) ................................................................................................................................................................................35

1592040000 XR30-60-70T EN v1.3 2020.08.26 XR30-60-70T 4/40
13.5 EXTERNALWARNINGALARM(IXF=EAL)..........................................................................................................................................................35
13.6 EXTERNALLOCKALARM(IXF=BAL)..................................................................................................................................................................35
13.7 EXTERNALPRESSUREALARM(IXF=PAL)..........................................................................................................................................................35
13.8 EVAPORATORFAN MODE(IXF=FAN)...............................................................................................................................................................35
13.9 REMOTEHOLIDAY MODE(IXF=HDF)................................................................................................................................................................35
13.10 REMOTEONOFF (IXF=ONF)..............................................................................................................................................................................35
13.11 LIGHTOUTPUT(IXF=LIG)..................................................................................................................................................................................35
13.12 CHANGECONFIGURATION(IXF=CC)................................................................................................................................................................35
13.13 MOTIONSENSORDETECTOR(IXF=EMT)..........................................................................................................................................................35
14. ALARMSIGNALLING.............................................................................................................................................................................................35
14.1 ALARMRECOVERY..........................................................................................................................................................................................36
15. SERIAL COMMUNICATION...................................................................................................................................................................................36
16. INSTALLATION AND MOUNTING.........................................................................................................................................................................36
17. WIRING DIAGRAM...............................................................................................................................................................................................36
17.1 XR70T..............................................................................................................................................................................................................36
17.2 XR60T..............................................................................................................................................................................................................37
17.3 XR30T..............................................................................................................................................................................................................37
18. TECHNICALSPECIFICATIONS................................................................................................................................................................................37
19. APPENDIX.............................................................................................................................................................................................................39
19.1 TOOLS .............................................................................................................................................................................................................39
19.1.1 XH-REP..................................................................................................................................................................................................39
19.1.2 X-MOD..................................................................................................................................................................................................39
19.1.3 WIZMATE..............................................................................................................................................................................................39
19.1.4 HOTKEY.................................................................................................................................................................................................39
19.1.5 USB TO RS485 CONVERTER...................................................................................................................................................................39
19.2 EXAMPLE OFMENUNAVIGATIONANDPARAMETERMODIFICATION...........................................................................................................40

1592040000 XR30-60-70T EN v1.3 2020.08.26 XR30-60-70T 5/40
1. IMPORTANT USER INFORMATION
The symbol is intended to alert the user of a non-insultated voltage source within the
product area that is sufficiently high to constitute a risk of electric shock to persons.
The symbol is intended to alert the user of important operating and maintenance
(servicing) instructions.
Dixell Srl reserves the right to modify this user’s manual at any time without prior notice. The
documentation can be downloaded from the website www.fulltouch.info even prior to purchase.
This manual is an integral part of the product and must always be kept near the device for easy
and quick reference. The product cannot be used as a safety device. Please read this manual
very carefully be sure you understand the information provided before using the device.
Verify that the power supply voltage is correct before connecting the device. Do not expose it to
water orhumidity:use the controller only within the operating limits, avoiding sudden temperature
changes and high atmospheric humidity in order to prevent condensation from forming.
Recommendations: disconnect all the electrical connections before performing any maintenance
task; insert the probe where it cannotbe reached by the End User; the device must not be opened;
consider the maximum current that can be applied to each relay; make sure that the wires of the
probes, of the loads and the electical power supply cables are sufficiently separated from each
other, without crossing or intertwining. In case of applications in industrial environments, it may
be useful to use the main filters as well as the inductive loads.
The customer shall bear full responsibility and risk for product configuration in order to achieve
the the final installation of the equipment/system. Upon the customer's request and following a
specific agreement, Dixell Srl may be present during the start-up of the final machine/application,
as a consultant, however, under no circumstances can the company be held responsible for the
correct operation of the final equipment/system.
Since Dixell products are part of a high-level technology, a qualification and a
configuration/programming/commissioning stage is required to best use them. Otherwise, these
products may malfunction and Dixell cannot be held responsible. The product must not be used
in any way that differs from that stipulated in the documentation.
The device must always be installed inside an electrical panel that can only be accessed by
authorised personnel. For safety purposes, the keyboard must be the only part that can be
reached.
The electrical wiring connections must never be modify while the device is being used.

1592040000 XR30-60-70T EN v1.3 2020.08.26 XR30-60-70T 6/40
It is good practice to bear in mind the following indications for all Dixell products:
oPrevent the electronic circuits from getting wet as contact made with water, humidity or any
other type of liquid can damage them. Comply with the temperature and humidity limits
specified in the manual in order to store the product correctly.
oThe device must not be installed in particularly hot environments as high temperatures can
damage the electronic circuits and/or plastic components forming part of the casing. Comply
with the temperature and humidity limits specified in the manual in order to store the product
correctly.
oUnder no circumstances is the device to be opened - the user does not need any internal
component. Please contact qualified service personnel for any assistance.
oPrevent the device from being dropped, knocked or shaken as either can cause irreparable
damage.
oDo not clean the device with corrosive chemical products, solvents or aggressive detergents.
oThe device must not be used in applications that differ from that specified in the following
document.
Separate the power supply of the device from the rest of the electrical devices connected
inside the electrical panel. The secondary of the transformer must never be connected to
the earth.
Dixell Srl reserves the right to change the components of its products, even without notice,
ensuring the same and unchanged functionality.
2. PRODUCT DISPOSAL (WEEE)
In compliance with the Directive 2002/96/EC of the European Parliament and of the Council of January 27th
2003 and to the relative national legislation, please note that:
There lies the obligation not to dispose of electrical and electronic waste as municipal waste
but to separate the waste.
Public or private collection points must be used to dispose of the goods in accordance with
local laws. Furthermore, at the end of the product's life, it is also possible to return this to the
retailer when a new purchase is made.
This equipment may contain hazardous substances. Improper use or incorrect disposal can
have adverse effects on human health and the environment.
The symbol shown on the product or the package indicates that the product has been placed
on the market after August 13th 2005 and must be disposed of as separated waste.
Should the product be disposed of incorrectly, sanctions may be applied as stipulated in
applicable local regulations regarding waste disposal.
Please consider the environment before printing this manual.

1592040000 XR30-60-70T EN v1.3 2020.08.26 XR30-60-70T 7/40
3. GENERALITIES
The XR-T is a microprocessor-based controller suitable for applications on medium or low temperature
ventilated refrigeration units. It has 4 relay outputs to control compressor, fans, light and defrost or auxiliary
outputs. The device is also provided with up to 4 NTC, PTC or PT1000 probe inputs. There are up to 2
configurable digital inputs. By using the HOT-KEY it is possible to program the device quickly and easily. The
controller implements Full Touch technology.
3.1 USEFUL INFORMATION
Stay tuned on www.fulltouch.info
CONTACT: [e-mail]
4. USER INTERFACE
XR-T has a capacitive user interface with Full
Touch technology. The whole display area is
used to interact with the device. Specific gestures
are used to enable or disable functions, browse
through screens and operational modes and
modify the configuration of the device.
4.1 SCREENS
SCREEN
DESCRIPTION
Home: this screen shows temperature value,
measurement unit and active alarms only. This is the
first screen after power on or after exit from other status
Virtual Keyboard: this screen shows available
functions. Activated function will blink when this screen
is visualized.
Info: This screen shows activated functions and
regulation outputs (compressor, ventilators).
Programming Mode: This screen enables the
modification of the Set point or parameters.

1592040000 XR30-60-70T EN v1.3 2020.08.26 XR30-60-70T 8/40
Setpoint Menu: This screen enables the modification of
the Set Point value.
Parameter Menu: These screens enable the
modification of all parameter values.
Stand-By: in this condition all outputs are deactivated.
HotKey Download: “PRG” blinks during download
operations (copy from HotKey to the internal memory)
HotKey Upload: “PRG” blinks during upload operations
(copy from internal memory to the HotKey)
X9: it is possible to create the label of the parameter to
be visualized or modified.
4.2 ICONS
DESCRIPTION MODE FUNCTION
LIGHT
OFF Function not available
FLASH When in the Virtual Keyboard screen: light output ON
ON When in the Virtual Keyboard screen: light output OFF
COMPRESSOR
OFF When in the Loads Info screen: compressor output OFF
FLASH Anti short cycle delay is running
ON When in the Loads Info screen: compressor output ON
FAN
OFF When in the Loads Info screen: evaporator fan output OFF
FLASH Activation delay is running
ON When in the Loads Info screen: evaporator fan output ON
DEFROST
OFF Function not available
FLASH When in the Virtual Keyboard screen: defrost ON
ON When in the Virtual Keyboard screen: defrost OFF
AUX
OFF Function not available
FLASH When in the Virtual Keyboard screen: AUX output ON
ON When in the Virtual Keyboard screen: AUX output OFF

1592040000 XR30-60-70T EN v1.3 2020.08.26 XR30-60-70T 9/40
ENERGY SAVING
OFF Function not available
FLASH When in the Virtual Keyboard screen: energy saving ON
ON When in the Virtual Keyboard screen: energy saving OFF
PULL DOWN
OFF Function not available
FLASH When in the Virtual Keyboard screen: pull down ON
ON When in the Virtual Keyboard screen: pull down OFF
ALARM
OFF No alarm is active
FLASH
ON Some alarm is active
Celsius Degree
OFF Not used
FLASH Not used
ON Measurement units: Celsius degree
Fahrenheit Degree OFF Not used
FLASH Not used
ON Measurement units: Fahrenheit degree
ONOFF
OFF
FLASH
ON Only and always ON icon when the device is in standby mode
PROG LEVEL 1
OFF
FLASH PROG LEVEL 1 and PROG LEVEL 2 icons toggle when the visualized value is
editable
ON First level (parameter groups) of the parameter menu is visualized
PROG LEVEL 2
OFF
FLASH PROG LEVEL 2 and PROG LEVEL 1 icons toggle when the visualized value is
editable
ON Second level (parameter labels) of the parameter menu is visualized
RADIO ON OFF Not used
FLASH Not used
ON Not used
PROGRAMMING
MODE
OFF Programming mode disabled
FLASH
ON Programming mode enabled
BACK OFF
FLASH
ON Used to go back to previous levels on the menu tree
ENTER OFF Set point menu disabled
FLASH
ON Set point menu enabled
BROWSING
OFF No other (lateral) screens available
FLASH
ON Other (lateral) screens available

1592040000 XR30-60-70T EN v1.3 2020.08.26 XR30-60-70T 10/40
4.3 GESTURES
GESTURE
NAME
HOW
-
TO
DESCRIPTION
ONE TAP Press a specific area
of the screen with a
finger for 1 sec
Switch ON / Switch OFF: when in Virtual
Keyboard, use this to turn on/off a specific
function. When in Programming mode, use this to
select a parameter or a parameter value.
TAP and
HOLD
Press any place of
the screen with a
finger for 3 sec
Enter / Save: use this to enter Programming
mode or Parameter menu and to save
modifications. When in Virtual Keyboard, use this
on the “ONOFF” to switch OFF and ON the
device.
H-SWIPE
Drag a finger across
the screen, from left
to right or from right
to left
Browse: use horizontal swipe (right to left or left
to right) to browse through HOME, Virtual
Keyboard and Info View. When in programming
mode: use horizontal swipe to browse through
parameter menu.
V-SWIPE
Drag a finger across
the screen, from top
to bottom or from
bottom to top
(overlapping only one
of the digits)
Modify: use vertical swipe (from top to bottom or
bottom to top) to change a parameter value.
4.4 HOME BROWSING
Use H-SWIPE to move through the screens. The logic implements a circular browsing: H-SWIPE to left or to
right is possible. A programmable timeout is implemented to return HOME from any lateral screen.
4.5 STAND-BY MODE
When in HOME screen, H-swipe to go to the Virtual Keyboard screen and then touch the OFF icon for 3 sec.
All outputs and alarms are deactivated in Stand-by mode.
4.6 PROGRAMMING MENU
It is possible to unlock the programming menu by touching any area of the display for 3 sec. Both SET and
PRG icons will blink until the programming menu is unlocked.

1592040000 XR30-60-70T EN v1.3 2020.08.26 XR30-60-70T 11/40
4.7 SETPOINT MENU
When in Programming Menu, it is possible to enter the Setpoint Menu by touching the SET icon for 3 sec.
Both SET and PRG icons will blink until the Setpoint Menu is unlocked. Both PROG LEVEL icons start
toggling to indicate that the visualized value is editable. Press the BACK icon to exit (come back to the
Programming Menu) without saving.
4.8 HOTKEY – UPLOAD
When in Programming Menu, it is possible to activate the HotKey Upload Menu function to save the
current device configuration (parameter values) into the external memory. To do this, follow these
instructions:
1. H-swipe to go on the UPL screen
2. Insert the HotKey (on the 5-pin ports on the back of the device)
3. Touch the PRG icon for 3 sec
4. The copying procedure will start and the PRG icon will blink during the copy operations
5. At the end of the copying procedure, a message will notify the user that the operation has been
competed successfully:
a. End: all parameters have been copied
b. Err: some error occours during copying operations
4.9 HOTKEY – DOWNLOAD
When in Power-off or in Stand-by mode, it is possible to activate the HotKey Download Menu function to
copy a new configuration (parameter values) into the current device memory. To do this, follow these
instructions:
1. Insert the HotKey (on the 5-pin ports on the back of the device)
2. Touch the OFF icon for 3 sec
3. After power-on, the copying procedure will start automatically and the PRG icon will blink during the
copy operations
4. At the end of the copying procedure, a message will notify the user that the operation has been
competed successfully:
a. End: all parameters have been copied
b. Err: some error occours during copying operations
4.10 X9
Every parameter is normally identified by a unique label that can have two or three alphanumeric characters.
When in the “X9” Screen, it is possible to create the parameter label by swiping-up every single part of the
label itself (first, second and third char). The system is able to drive the user through the available symbols,
showing only the available ones to speed up the creation of the label.
For example, if a modification of the “interval between defrosts” parameters is required (label “idF”), these
are the steps to follow:
- Enter the X9 screen
- Swipe-up or down the first char position (lower segment on the left) until char “i” (lowercase) appears

1592040000 XR30-60-70T EN v1.3 2020.08.26 XR30-60-70T 12/40
- Move to the second char position (segment in the middle) and swipe-up or down until char “d”
appears
- Move on the third char position (segment on the right) and swipe-up or down until char “F” appears
- Enter the par. value by touching the PRG icon for 3 sec.
NOTE: pay attention to the upper or lower case when browsing through the available characters.
For simplicity, here is the complete list of available characters: A, b, C, d, E, F, G, H, i, L, M, n, o, P, q, r, S, t,
u, V, Y, 0, 1, 2, 3, 4, 5, 6, 7, 8 and 9.
4.11 PARAMETER MENU
When in Programmin Menu, it is possible to enter the Parameter Menu touching the PRG icon for 3 sec.
The Prog Level 1 icon will indicate the first level of the programming menu (group labels).
The Browsing icon will indicate that there are other groups of parameters.
…
When in PROG LEVEL 1, it is possible to browse through the available groups of parameters by using the H-
swipe gesture. The circular construction of this menu permits to move left or right through the groups.
Here are the available groups:
Group Label Description
rEG Main regulation parameters
Prb Probe configuration parameters
diS Visualization parameters
dEF Defrost configuration parameters
FAn Evaporator and condenser fan configuration parameters
AUS Auxiliary regulator parameters
ALr Alarm configuration parameters
oUt Digital and analogue output configuration parameters
inP Digital input configuration parameters
ES Energy saving configuration parameters
Cnt Counters, read only values
rtC Real Time Clock configuration parameters
E2 Memory storage management

1592040000 XR30-60-70T EN v1.3 2020.08.26 XR30-60-70T 13/40
CoM Serial Communication port configuration parameters
Ui User Interface configuration parameters
inF Information, read only parameters
PAS Password for entering protected menu parameters
4.12 PASSWORD MENU
When in the PAS group, it is possible to set the password value by touching the PRG icon for 3 sec.
V-swipe on a single digit to modify the value, then confirm the password value by touching the PRG icon for
3 sec.
The new value will blink and after 2 sec the display will show:
Pr2 if the password is correct
Err if the password value is wrong
After 2 sec the display will show the first group label (rEG) with a blinking PRG icon to indicate that protected
parameters now are editable.
5. PARAMETER TABLE
Here are the descriptions of the device parameters.
5.1 PARAMETER DESCRIPTION
5.1.1 Main regulation parameters - rEG
SEt
S
et Point:
range from LS to US
LS
Minimum Set Point:
(
-
100.0°C to SET;
-
148°F to SET)
fix
the minimum value for t
he set point.
US
Maximum Set Point:
(SET to 200.0°C; SET to 392°F) fix the maximum value for the set point.
HY Compressor regulation differential in normal mode: (0.1 to 25.0°C; 1 to 45°F) set point
differential. Compressor Cut
-
IN is
T > SET + HY
. Compre
ssor Cut
-
OUT is
T<=SET
.
HYE
Compressor regulation differential in energy saving mode: (0.1 to 25.0°C; 1 to 45°F) set point
differential. Compressor Cut
-
IN is
T > SET + HES + HYE
. Compressor Cut
-
OUT is
T<= SET + HES
.
odS
Output activation delay at start-up: (0 to 255 min) this function is enabled after the instrument
power
-
on and delays the output activations.
AC Anti-short cycle delay: (0 to 50 min) minimum interval between a compressor stop and the
following restart.
r
tr
Regulation percentage=F(P1; P2)
(100=P1; 0=P2)
:
100=P1 only; 0=P2 only
CCt
Maximum duration for Pull Down: (0.0 to 23h50min, res. 10min) after elapsing this interval of time,
the super cooling function is immediately stopped
CCS
Pull Down phase differential (SET+CCS or SET+HES+CCS): (-12.0 to 12.0°C; -21 to 21°F) during
any super cooling phase the regulation SETPOINT is moved to SET+CCS (in normal mode) or to
SET+HES+CCS
(in energy saving mode)
oHt Threshold for automatic activation of Pull Down in normal mode (SET+HY+oHt): (1.0 to 12.0°C;
1 to 21°F) this is the upper limit used to activate the super cooling function.
oHE
Threshold for automatic activation of Pull Down in energy saving mode
(SET+HES+HYE+oHE): (1.0 to 12.0°C; 1 to 21°F) this is the upper limit used to activate the super
cooling function.

1592040000 XR30-60-70T EN v1.3 2020.08.26 XR30-60-70T 14/40
Con
Compressor ON time with faulty probe: (0 to 255 min) time during which the compressor is active
in case of faulty thermostat probe.
With
CY=0
compressor is always OFF.
CoF
Compressor OFF time with faulty probe: (0 to 255 min) time during which the compressor is OFF
in case of faulty thermostat probe.
With
Cn=0
compressor is always active.
5.1.2 Probe configuration parameters – Prb
P1C
Probe P1 selection:
(ntC; PtC; Pt1)
ntC
=NTC type;
PtC
=PTC type;
Pt1
=PT1000 type
P2C
Probe P2 selection
:
(ntC; PtC; Pt1)
ntC
=NTC type;
PtC
=PTC type;
Pt1
=PT1000 type
P3C
Probe P3 selection:
(ntC; PtC; Pt1)
ntC
=NTC type;
PtC
=PTC type;
Pt1
=PT1000 type
P4C
Probe P4 selection:
(ntC; PtC; Pt1)
ntC
=NTC type;
PtC
=PTC type;
Pt1
=PT1000
type
ot Probe P1 calibration: (-12.0 to 12.0°C; -21 to 21°F) allows to adjust any possible offset of the first
probe.
P2
P
Probe P2 presence
:
n
= not present;
Y
=
present
.
oE Probe P2 calibration: -12.0 to 12.0°C; -21 to 21°F) allows to adjust any possible offset of the
second
probe
.
P3P
Probe P
3
presence
:
n
= not present;
Y
= the defrost
present
.
o3 Probe P3 calibration: (-12.0 to 12.0°C; -21 to 21°F) allows to adjust any possible offset of the third
probe.
P
4P
Probe P
4
presence
:
n
= not present;
Y
=
present
.
o4 Probe P4 calibration: (-12.0 to 12.0°C; -21 to 21°F) allows to adjust any possible offset of the forth
probe.
5.1.3 Visualization parameters - diS
CF
Temperature measurement unit:
(°C; °F)
°C
= Celsius;
°F
= Fahrenheit.
rE
S
Temperature resolution
:
(dE; in)
dE
= decimal;
in
=
integer.
Lod Probe default displayed: (P1; P2; P3; P4; SEt; dtr; USr) Px=probe “x”; SEt=set point; dtr=do not
use it
.
rEd Remote probe displayed (for XH-REP): (P1; P2; P3; P4; SEt; dtr; USr) Px=probe “x”; SEt=set
point;
dtr
=do not use it
.
dLY
Temperature display delay: (0.0 to 20min00sec, res. 10 sec) when the temperature increases, the
display is updated of 1°C or 1°F after this time.
dtr Probe visualization percentage, F(P1; P2): (0 to 100) with dtr=1 the display will show this value
VALUE=0.01*P1+0.9
9*P2
5.1.4 Defrost configuration parameters - dEF
EdF
Defrost mode:
in
=fixed intervals;
rtC
=following real time clock
tdF
Defrost type: EL
=electrical heaters;
in
=hot gas;
dFP Probe selection for defrost control: (nP; P1; P2; P3; P4) nP=no probe; Px=probe “x”. Note:
P4
=Probe on Hot Key plug.
dtE End defrost temperature: (-55 to 50°C; -67 to 122°F) sets the temperature measured by the
evaporator probe (
dFP
), which causes the end of defrost cycle.
idF Interval between two successive defrost cycles: (0 to 255 hours) determines the time interval
between the beginning of two defrosting cycles.
MdF Maximum length of defrost cycle: (0 to 255 min; 0 means no defrost) when P2P=n (no evaporator probe presence) it sets the defrost duration, when P2P=Y (defrost end based on
evaporator temperature) it sets the maximum length for the defrost cycle.
dSd
Start defrost delay:
(0 to 255 min) delay in defrost activation.
StC Compressor stop before starting any defrost: (0 to 900 sec) interval with compressor OFF
before activating hot gas cycle
dFd Display during defrost: (rt; it; SP; dF) rt = real temperature; it = start defrost temperature;
SP
= SET
-
POINT;
dF
= label “
dF
”.
dAd Temperature display delay after any defrost cycle: (0 to 255 min) delay before updating the
tempe
rature on the display after the end of any defrost.
Fdt
Draining time:
(0 to 255 min)
regulation
d
elay after finishing a defrost phase
Hon Drain heater enabled after draining time (par. Fdt): (0 to 255 min) the relative output will stay on
after draining
time.
dPo
Defrost cycle enebled at stat
-
up
:
(n; Y) enable
s
defrost at power on.
HYP
Differential temperature during any pre
-
defrost phase:
(
-
12.0 to 12.0°C;
-
21 to 21°F)

1592040000 XR30-60-70T EN v1.3 2020.08.26 XR30-60-70T 15/40
Pd2
Defrost output deactivation delay:
(0 to 255 sec)
dAF
Pre
-
defrost time:
(0 to
255 min)
od1 Automatic defrost (at the beginning of any energy saving mode): (n; Y) n=function disabled;
Y
=function enabled
od2 Optimized defrost: (n;Y) n= function disabled; Y= the controller needs a temperature probe
placed on the evaporator surface
to monitor the presence of ice during any defrost phase.
dSt Temperature sampling time during an optimized defrost (valid only if od2=yes): (1 to 255
sec) interval used to analyz
e the evaporator temperature and define the defrost phase
SYd Type of synchronized defrost: (n; SYn; nSY) n = function disabled; SYn = synchronized, all devices connected will start a defrost phase at the same time. nSY = de-synchronized, all devices
connected will delay the beginning of the same defrost phase.
dt1 Differential temperature for latent heating control (0.1 to 1.0 °C) to catch the latent heating
phase during any defrost
ErS
Restart regulation after dripping time, when defrost Syd = nSY: n
= disabled;
Y
= enabled
ndE Number of devices connected to the virtual network for random defrost (valid if Syd=rnd): (1
to 20) numb
er of devices connected to the same network for syncro or desyncro defrost.
5.1.5 Evaporator and condenser fan configuration parameters - FAn
FAP Probe selection for evaporator fan: (nP; P1; P2; P3; P4) nP=no probe; Px=probe “x”. Note:
P4
=Probe on Hot Key
plug.
FSt Evaporator fan stop temperature: (-55 to 50°C; -67 to 122°F) setting of temperature, detected by evaporator probe. Above this temperature value fans are always OFF. NOTE: it works only for
the
evaporator fan, NOT for the condenser fan.
HYF Evaporator fan regulator differential: (0.1 to 25.5°C; 1 to 45°F) evaporator fan will stop when the
measured temperature (from FAP) is T<FSt
-
HYF.
FnC
Evaporator fan operating mode: (Cn; on; CY; oY)
Cn = runs with the compressor, duty-cycle when compressor is OFF (see FoF,Fon, FF1 and
Fo1 parameters) and OFF during defrost
on = continuous mode, OFF during defrost
CY = runs with the compressor, duty-cycle when compressor is OFF (see FoF,Fon, FF1 and
Fo1 parameters) and ON during defrost

oY
=
continuous mode, ON during defrost
Fnd Evaporator fan delay after defrost cycle: (0 to 255 min) delay before fan activation after any
defrosts.
FCt
Differential for cyclic activation of evaporator fans
:
(0 to 50°C)
FSU Evaporator fan operating mode: (Std; Fon; FoF) Std = standard mode, evaporator fan uses par
FnC
;
Fon
= evaporator Fan always on;
FoF
= evaporator fan always off.
Ft Evaporator fan controlled during defrost: (n; Y) n= evaporator fan uses par. FnC during any
defrost;
Y
= evaporator fan regulator is active during any defrost.
Fon Evaporator fan ON time in normal mode (with compressor OFF): (0 to 255 min) used when
energy saving status is not active.
FoF Evaporator fan OFF time in normal mode (with compressor OFF): (0 to 255 min) used when
energy saving status is not active.
Fo1 Evaporator fan ON time in energy saving mode (with compressor OFF) (0 to 255 min) used
when energy saving status is active.
FF1 Evaporator fan OFF time in energy saving mode (with compressor OFF): (0 to 255 min) used
when energy saving status is active.
Fd1
Evaporator fan delay:
(0 to 255 sec) delay before activating evaporator fan
Fd2 Evaporator fan delay after closing door: (0 to 255 sec) delay before activating evaporator fan
and after closing the door
FAC Probe selection for condenser fan: (nP; P1; P2; P3; P4) nP=no probe; Px=probe “x”. Note:
P4
=Probe on Hot Key plug.
St2 Set Point 2 regulation (for condenser fan): (-55 to 50°C; -67 to 122°F) setting of temperature
detecte
d by evaporator probe.
Above this
value of temperature fans are always OFF.
HY2 Set Point 2 differential (for condenser fan): (0.1 to 25.5°C; 1 to 45°F) differential for evaporator
ventilator regulator
FCC
Condenser fan operating mode: (Cn; on; CY; oY)
Cn = runs with the compressor and OFF during defrost
on = continuous mode, OFF during defrost
CY = runs with the compressor and ON during defrost

oY
= continuous mode, ON during defrost

1592040000 XR30-60-70T EN v1.3 2020.08.26 XR30-60-70T 16/40
Fd3
Condenser
fan
activation
delay:
(0 to 255 sec) delay before acti
vating
condenser
fan
Fd4
Condenser fan deactivation delay:
(0 to 255 sec) delay before deactivating
condenser
fan
5.1.6 Auxiliary regulator parameters - AUS
ACH
Type of control for auxiliary regulator
:
(Ht; CL)
Ht
= heating;
CL
= cooling.
SAA Set Point for auxiliary regulator: (-55.0 to 150.0°C; -67 to 302°F) it defines the room temperature
set point to switch auxiliary relay.
SHY Auxiliary regulator differential: (0.1 to 25.5°C; 1 to 45°F) differential for auxiliary output set point. ACH=CL, AUX Cut in is [SAA+SHY]; AUX Cut out is SAA.

ACH=Ht
, AUX Cut in is [
SAA
–
SHY]
; AUX Cut out is
SAA
.
ArP Probe selection for auxiliary regulator: (nP; P1; P2; P3; P4) nP = no probe, the auxiliary relay is
switched only by the digital input;
P
x
=
probe “x”.
Note:
P4
=Probe on H
ot Key plug
.
Sdd Auxiliary regulator disabled during any defrost cycle: (n; Y) n= the auxiliary relay operates
during defrost.
Y
= the auxiliary relay is switched off during defrost.
btA Base time for parameters Ato and AtF: (SEC; Min) SEC = base time is in second; Min = base
time is in minutes.
Ato
Interval of time with auxiliary output ON
:
0 to 255 (base time defined in par.
btA
)
AtF
Interval of time with auxiliary output OFF
:
0 to 255 (base time defined in par.
btA
)
5.1.7 Alarm configuration parameters
ALP Probe selection for temperature alarms: (nP; P1; P2; P3; P4) nP=no probe; Px=probe “x”. Note:
P4
=Probe on Hot Key plug.
ALC
Temperature alarms configuration:
(
Ab, rE
)
Ab
= absolute;
rE
= relative.
ALU
High temperature alarm: when this temperature is reached, the alarm is enabled after the Ad
delay time.
If ALC=Ab ALL to 150.0°C or ALL to 302°F.

If
ALC=rE

0.0 to 50.0°C or 0 to 90°F.
ALL
Low temperature alarm: when this temperature is reached, the alarm is enabled after the Ad
delay time.
If ALC=Ab -55.0°C to ALU or -67°F to ALU.

If
ALC=rE

0.0 to 50.0°C or 0 to 90°F.
AFH
Temperature alarm differential:
(0.1 to 25.0°C; 1 to 45°F) alarm differential.
ALd Temperature alarm delay: (0 to 255 min) delay time between the detection of an alarm condition
and the relative alarm signalling.
dot Temperature alarm delay with open door: (0.0 to 24h00min, res. 10 min) delay time between the detection of a temperature alarm condition and the relative alarm signalling, after starting up the
instrument.
dAo Temperature alarm delay at start-up: (0.0 to 24h00min, res. 10 min) delay time between the detection of a temperature alarm condition and the relative alarm signalling, after starting up the
instrument.
AP2 Probe selection for second temperature alarm: (nP; P1; P2; P3; P4) nP=no probe; Px=probe
“x”.
Note:
P4
=Probe on Hot Key plug.
AU1 Pre-alarm threshold for second temperature alarm (absolute value): (-55.0 to 150.0°C; -67 to
302°F)
AH1
Second high temperature pre
-
alarm differential
:
(0.1 to 25.0°C; 1 to 45
°F)
Ad1 Second high temperature pre-alarm delay: (0 to 255 min; 255 = not used) delay time between
the detection of a condenser pre-alarm condition and the relative alarm signalling.
AL2
Second low temperature alarm
:
(
-
55.0 to 150.0°C;
-
67 to 302°F)
AU2
Second high temperature alarm
:
(
-
55.0 to 150.0°C;
-
67 to 302°F)
AH2
Second temperature alarm differential
:
(0.1 to 25.0°C; 1 to 45°F)
Ad2 Second temperature alarm delay: (0 to 255 min; 255 = not used) delay time between the
detection of a condenser alar
m condition and the relative alarm
signalling
.
dA2
Second temperature alarm delay at start
-
up:
(0.0 to 24h00min, res. 10 min)
bLL Compressor off due to second low temperature alarm: (n; Y) n = no, the compressor continues to work; Y = yes, the compressor is switched off while the alarm is ON; in any case, the regulation
restarts after AC time at minimum.
AC2 Compressor off due to second high temperature alarm: (n; Y) n = no, the compressor continues to work; Y = yes, the compressor is switched off while the alarm is ON; in any case, the
regulation restarts after AC time at minimum.

1592040000 XR30-60-70T EN v1.3 2020.08.26 XR30-60-70T 17/40
SAF Differential for anti-freezing control: (-12.0 to 12.0°C; -21.0 to 21.0°F) the regulation stops if
T<SET+SAF
tbA Alarm relay deactivation: (n; Y) n = no, it is not possible to deactivate neither the buzzer nor any digital output set as an alarm; Y = yes, it is possible to deactivate both the buzzer and the digital
output set as an alarm.
5.1.8 Digital and analogue output configuration parameters - out
oAx
(x=2, 3, 4)
Relay output oAx configuration: (nu; CP1; dEF; FAn; ALr; LiG; AUS; db; onF; HES; Cnd)
nu=not used; CP1=compressor; dEF=defrost; FAn=ventilators; ALr=alarm; LiG=light;
AUS=auxiliary relay; onF=always ON with instrument ON; db=neutral zone; HES=night
blinds; Cnd=condenser fan; CP2=second compressor; dF2=second defrost; HEt=heater
control;
inV
=do not use it.
AoP Alarm relay polarity: (oP; CL) oP = alarm activated by closing the contact; CL = alarm
activated by opening the contact
5.1.9 Digital input configuration parameters - inP
ibt Base time for digital inputs: (SEC; Min) SEC = seconds; Min = minutes. Delay in activating the
function linked to the digital inputs.
i1P Digital input 1 polarity: (oP; CL) oP = activated by closing the contact; CL = activated by opening
the co
ntact.
i1F
Digital input 1 configuration: (nu; dor; dEF; AUS; ES; EAL; bAL; PAL; FAn; HdF; onF; LiG; CC;
EMt)
nu=not used
dor = door switch function
dEF = defrost activation
AUS = auxiliary output
ES = energy saving mode activation
EAL = external warning alarm
bAL = external lock alarm
PAL = external pressure alarm
FAn = evaporator fan control
HdF = holiday defrost
onF = ON/OFF status change
LiG = light output control
CC = change configuration (between C1 and C2)

EMt
=
Motion sensor X
-
MOD
did Digital inputs 1 alarm delay (base time depends on par. ibt): (0 to 255) delay between the
detection of an external event and the activation of the relative function.
i2P Digital input 2 polarity: (oP; CL) oP = activated by closing the contact; CL = activated by opening
the contact.
i2F
Digital input 2 configuration: (nu; dor; dEF; AUS; ES; EAL; bAL; PAL; FAn; HdF; onF; LiG; CC;
EMt)
nu = not used
dor = door switch function
dEF = defrost activation
AUS = auxiliary output
ES = energy saving mode activation
EAL = external warning alarm
bAL = external lock alarm
PAL = external pressure alarm
FAn = evaporator fan control
HdF = holiday defrost
onF = ON/OFF status change
LiG = light output control
CC = change configuration (between C1 and C2)

EMt
=
Motion sensor X
-
MOD
d2d Digital inputs 2 alarm delay (base time depends on par. ibt): (0 to 255) delay between the
detection of an external event and the activation of the
relative function.
nPS Number of external pressure switch alarms before stopping the regulation: (0 to 15) after reaching nPS events in the digital input alarm delay (par. dxd), the regulation will be stopped and a
manual restart (ON/OFF, power OFF and po
wer ON) will be required

1592040000 XR30-60-70T EN v1.3 2020.08.26 XR30-60-70T 18/40
odC Compressor and fan status after door opening: (no; FAn; CPr; F-C): no = normal;
FAn = Fans OFF; CPr = Compressor OFF; F
-
C = Compressor and fans OFF.
rrd Regulation restart after door alarm: (n; Y) n = no regulation if the door is open; Y = when the rrd
timer elapses, the regulation restarts even if a open door alarm is ON.
CLi Light output activation from door input: (n; Y) the activation of a digital input set as ixF=dor
forces the light output ON.
LCi Time with light output forced ON (0=function disabled): (0 to 255 min) interval with light output
forced ON.
n01 Number of motion detections before activating light output (valid if ixF=EMt): (0 to 10)
number of motion sensor detections before forcing the light output ON.
t01 Time with light output forced ON after motion detection: (0 to 255 min) interval with light output
forced ON from motion sensor.
5.1.10 Energy saving configuration parameters - ES
ErA Energy saving algorithm: (nu; bAS) nu=disabled, the energy saving mode activation is by button, real time clock or digital input; bAS=basic algorithm, the energy saving mode activation depends
on the the digital input.
HES Energy saving mode temperature differential: (-30.0 to 30.0°C; -54 to 54°F) sets the increasing
value of the set point during the Energy Saving cycle.
LdE
Energy saving controls the lights (lights OFF when energy saving is active): (n; Y) lights off
when energy saving
mode is active
StE Period to switch from normal mode to energy saving mode: (0.0 to 24h00min, res. 10 min) if the door stay closed for StE time, the energy saving mode will be activated. NOTE: this will require
a door switch
to work.
EtS Period to switch from energy saving mode to normal mode: (0.0 to 24h00min, res. 10 min)
maximum time for energy saving mode. NOTE: this will require a door switch to work.
dS Door opening time to switch from EtS to StE: (0 to 999 sec) the energy saving mode will be immediately deactivated as soon as the door stays open more than the dS time. NOTE: this will
require a door switch to work.
nES Number of motion detections before disabling energy saving mode (valid if ixF=EMt): (0 to
255) number of motion sensor detections before disabling the energy saving mode.
5.1.11 Counters, read only values - Cnt
n1H
Number of activations for relay output oA1 (tho
usands of)
n1L
Number of activations for relay output oA1 (units of)
n
2H
Number of activations for relay output oA
2
(thousands of)
n2L
Number of activations for relay output oA
2
(units of)
n3H
Number of activations for relay output oA
3
(thousands of)
n3L
Number of activations for relay output oA
3
(units of)
n4H
Number of
activations for relay output oA
4
(thousands of)
n4L
Number of activations for relay output oA
4
(units of)
n5H
Number of total activation
of digital input 1 (thousand of)
n5L
Number of total activation of digital input 1 (units of)
n6H
Number of total
activation of digital input 2 (thousand of)
n6L
Number of total activation of digital input 2 (units of)
F1H
Number of working hours
for relay output oA1 (thousands of)
F1L
Number of working hours for relay output oA1 (units of)
F2H
Number of working h
ours for relay output oA2 (thousands of)
F2L
Number of working hours for relay output oA2 (units of)
F3H
Number of working hours for
relay output oA3 (thousands of)
F3L
Number of working hours for relay output oA3 (units of)
F4H
Number of working hours
for relay output oA4 (thousands of)
F4L
Number of working hours for relay output oA4 (units of)
5.1.12 Real Time Clock configuration parameters - rtC
Hur
Hour
s
:
0 to 23
h
ours

1592040000 XR30-60-70T EN v1.3 2020.08.26 XR30-60-70T 19/40
Min
Minute
s
:
0 to 59
min
utes
dAY
D
ay
of the week
:
Sun to Sat
dYM
Day of the month:
1 to 31
Mon
Month:
1 to 12
YAr
Year:
00 to 99
Hd1
First day of weekend:
(Sun to S
A
t; nu)
setting for the first day of the weekend.
Hd2
Second day of weekend:
(Sun to S
A
t; nu) setting for the second day of the weekend.
iLE Energy saving cycle start time on working days: (00h00min to 23h50min) during the Energy Saving cycle, the set point is increased by the value in HES so that the operation set point is
SET+HES
.
dLE Energy saving cycle duration on working days: (00h00min to 24h00min) sets the duration of
the Energy Saving cycle on working days.
iSE
Energy saving cycle
start time on
weekends
:
0
0h00min
to 23h50min
dSE
Energy saving cycle duration on weekends
:
0
0h00min
to 24h00min
ddx
Daily defrost enabled: (n; Y) to enable the Ld1 to Ld6 defrost operations for any day of the
week.
dd1 = Sunday defrost
dd2 = Monday defrost
dd3 = Tuesday defrost
dd4 = Wednesday defrost
dd5 = Thursday defrost
dd6 = Friday defrost

dd7
= Saturday defrost
Ldx Defrost start time: (00h00min to 23h50min) these parameters set the beginning of the programmable defrost cycles during any ddx day. Example: when Ld2=12.4, the second defrost
starts at 12:40 am during working days.
5.1.13 Memory storage management – E2
MAP
Current configuration
:
(
C
-
1; C
-
2
)
to change configuration used.
LdM Restore default factory settings: (n;Y) select Y and confirm to reload factory default values for
the configuration currently used.
rHA Reset HACCP values: (n; Y) select Y and confirm to reset the memorized min and MAX
temperature values (HACCP function
must be enabled)
.
5.1.14 Serial Communication port configuration parameters - CoM
Adr
Serial address:
(1 to 247) device address for Modbus communication
bAU
Baudrate:
(9.6; 19.2; 38.4; 57.6) select the correct baudrate for serial communication
PAr Parity control: (no; odd; EvE) no=no parity control; odd=odd parity control; EvE=even parity
control
5.1.15 User Interface configuration parameters - Ui
SCS User interface timeout: (1 to 255 sec) timeout before coming back to Home Screen or to
Programming M
e
nu
bS
Sound
Le
vel
:
(
0 to 5) select the sound level of the gestures
PSU Password for protected level Pr2: (000 to 999) insert a value to protect all the parameters set
on the level Pr2 from modification
5.1.16 Information, read only parameters - inF
d
P
1
Probe P1 value visu
al
ization
d
P
2
Probe P2 value visualization
d
P
3
Probe P3 value visualization
d
P
4
Probe P4 value visualization
rSE
Real regulation
Set Point
FdY
Firmware release date: day
FMt
Firmware release date: month
FYr
Firmware release date: year
rEL
Firmware r
elease: progressive number
S
U
b
Firmware sub release: progressive number
Ptb
Parameter map version

1592040000 XR30-60-70T EN v1.3 2020.08.26 XR30-60-70T 20/40
NOTE: some parameters are not present in models XR30T and XR60T due to lack of the relevant I/O’s.
5.2 PARAMETER CONFIGURATION 1
Group Par. Description Value Protected U.O.M. Range
rEG SEt Set Point 3.0 Pr1 °C LS to US
rEG LS Minimum Set point -100.0 Pr1 °C [-100.0°C to SET]
[-148.0°F to SET]
rEG US Maximum Set point 150.0 Pr1 °C [SET to 150.0°C]
[SET to 302.0°F]
rEG HY Compressor regulation differential in
normal mode 3.0 Pr1 °C [0.1°C to 25.0°C] [0.1°F to 45.0°F]
rEG HYE Compressor regulation differential in
energy saving mode 3.0 Pr1 °C [0.1°C to 25.0°C] [0.1°F to 45.0°F]
rEG odS Output activation delay at start-up 0 Pr1 min 0 to 255 min
rEG AC Anti-short cycle delay 0 Pr1 min 0 to 50 min
rEG rtr Regulation percentage=F(P1; P2)
(100=P1; 0=P2) 100 Pr2 0 to 100
rEG CCt Maximum duration for Pull Down 00:00 Pr2 hh:mm 0 to 23h50min
rEG CCS Pull Down phase differential (SET+CCS or
SET+HES+CCS) 0.0 Pr2 °C [-12.0°C to 12.0°C] [-21.6°F to 21.6°F]
rEG oHt Threshold for automatic activation of Pull
Down in normal mode (SET+HY+oHt) 10.0 Pr2 °C [0.0°C to 25.0°C] [0.0°F to 45.0°F]
rEG oHE Threshold for automatic activation of Pull Down in energy saving mode
(SET+HES+HYE+oHE) 10.0 Pr2 °C [0.0°C to 25.0°C]
[0.0°F to 45.0°F]
rEG Con Compressor ON time with faulty probe 10 Pr1 min 0 to 255 min
rEG CoF Compressor OFF time with faulty probe 15 Pr1 min 0 to 255 min
Prb P1C Probe P1 selection ntC Pr2 ntC; PtC; Pt1
Prb P2C Probe P2 selection ntC Pr2 ntC; PtC; Pt1
Prb P3C Probe P3 selection ntC Pr2 ntC; PtC; Pt1
Prb P4C Probe P4 selection ntC Pr2 ntC; PtC; Pt1
Prb ot Probe P1 calibration 0.0 Pr1 °C [-12.0°C to 12.0°C]
[-21.6°F to 21.6°F]
Prb P2P Probe P2 presence Y Pr1 n(0); Y(1)
Prb oE Probe P2 calibration 0.0 Pr1 °C [-12.0°C to 12.0°C]
[-21.6°F to 21.6°F]
Prb P3P Probe P3 presence no Pr1 n(0); Y(1)
Prb o3 Probe P3 calibration 0.0 Pr1 °C [-12.0°C to 12.0°C]
[-21.6°F to 21.6°F]
Prb P4P Probe P4 presence no Pr1 n(0); Y(1)
Prb o4 Probe P4 calibration 0.0 Pr1 °C [-12.0°C to 12.0°C]
[-21.6°F to 21.6°F]
diS CF Temperature measurement unit: Celsius;
Fahrenheit °C Pr1 °C(0); °F(1)
diS rES Temperature resolution: decimal, integer dE Pr1 dE(0); in(1)
diS Lod Probe default displayed P1 Pr1 P1(0); P2(1); P3(2);
P4(3); SEt(4); dtr(5)
diS dLy Temperature display delay (resolution 10
sec) 00:00 Pr1 mm:ss 0.0 to 20min00sec
diS dtr Probe visualization percentage=F(P1;P2) (ex: dtr=1 means
VALUE=0.01*P1+0.99*P2) 99 Pr1 1 to 99
dEF EdF Defrost mode rtC Pr2 rtC(0); in(1)
dEF tdF Defrost type: electric heating, hot gas EL Pr2 EL(0); in(1)
dEF dFP Probe selection for defrost control P2 Pr2 nP(0); P1(1); P2(2); P3(3); P4(4)