Emerson Dixell XRi30T Wiring diagram

XRi30T –Full Touch
XRi31T –Full Touch
(V.1.2)

1592040010 XRi30-31T EN v1.2 2020.08.26 XRi30T-XRi31T 3/42
INDEX
1. IMPORTANT USER INFORMATION.....................................................................................................................................................................................5
2. PRODUCT DISPOSAL (WEEE) ..............................................................................................................................................................................................6
3. GENERALITIES......................................................................................................................................................................................................................7
3.1 USEFUL INFORMATION ............................................................................................................................................................................................7
4. USER INTERFACE .................................................................................................................................................................................................................7
4.1 SCREENS ....................................................................................................................................................................................................................7
4.2 ICONS.........................................................................................................................................................................................................................8
4.3 GESTURES..................................................................................................................................................................................................................9
4.4 HOME BROWSING ..................................................................................................................................................................................................10
4.5 STAND-BY MODE ....................................................................................................................................................................................................10
4.6 PROGRAMMING MENU..........................................................................................................................................................................................10
4.7 SETPOINT MENU.....................................................................................................................................................................................................10
4.8 HOTKEY –UPLOAD..................................................................................................................................................................................................11
4.9 HOTKEY –DOWNLOAD...........................................................................................................................................................................................11
4.10 X9.............................................................................................................................................................................................................................11
4.11 PARAMETER MENU ................................................................................................................................................................................................12
4.12 PASSWORD MENU..................................................................................................................................................................................................12
5. PARAMETER TABLE ...........................................................................................................................................................................................................13
5.1 PARAMETER DESCRIPTION.....................................................................................................................................................................................13
5.1.1 Main regulation parameters - rEG ...................................................................................................................................................................13
5.1.2 Probe configuration parameters –Prb ............................................................................................................................................................13
5.1.3 Variable Speed Compressor parameters - VSC................................................................................................................................................14
5.1.4 Visualization parameters –diS .........................................................................................................................................................................14
5.1.5 Defrost configuration parameters –dEF .........................................................................................................................................................14
5.1.6 Evaporator and condenser fan configuration parameters –Fan...................................................................................................................15
5.1.7 Auxiliary regulator parameters –AUS .............................................................................................................................................................16
5.1.8 Alarm configuration parameters......................................................................................................................................................................16
5.1.9 Digital and analogue output configuration parameters - out........................................................................................................................17
5.1.10 Digital input configuration parameters - inP .............................................................................................................................................17
5.1.11 Energy saving configuration parameters - ES ............................................................................................................................................18
5.1.12 Counters, read only values - Cnt..................................................................................................................................................................19
5.1.13 Real Time Clock configuration parameters - rtC ........................................................................................................................................19
5.1.14 Memory storage management –E2 ...........................................................................................................................................................20
5.1.15 Serial Communication port configuration parameters - CoM...................................................................................................................20
5.1.16 User Interface configuration parameters - Ui ............................................................................................................................................20
5.1.17 Information, read only parameters - inF ....................................................................................................................................................20
5.2 PARAMETER CONFIGURATION 1 ...........................................................................................................................................................................20
5.3 PARAMETER CONFIGURATION 2 ...........................................................................................................................................................................27
6. REGULATION .....................................................................................................................................................................................................................33
6.1 ONOFF COMPRESSOR.............................................................................................................................................................................................33
6.2 VARIABLE SPEED COMPRESSOR.............................................................................................................................................................................33
7. ENERGY SAVING ................................................................................................................................................................................................................33
7.1 BASIC ENERGY SAVING ALGORITHM .....................................................................................................................................................................33
7.1.1 PARAMETERS INVOLVED...................................................................................................................................................................................33
8. PULL DOWN FUNCTION....................................................................................................................................................................................................34
9. DEFROST OPERATIONS .....................................................................................................................................................................................................34
9.1 TIMED OR TEMPERATURE CONTROLLED MODE...................................................................................................................................................34
9.2 AUTOMATIC DEFROST............................................................................................................................................................................................34
9.3 OPTIMIZED DEFROST..............................................................................................................................................................................................34
10. EVAPORATOR FAN .......................................................................................................................................................................................................34
10.1 EVAPORATOR FAN AND DIGITAL INPUT................................................................................................................................................................35
11. CONDENSER FAN .........................................................................................................................................................................................................35
12. DIGITAL OUTPUTS........................................................................................................................................................................................................35
12.1 COMPRESSOR OUTPUT (OAX =CP1) ......................................................................................................................................................................35
12.2 DEFROST OUTPUT (OAX =DEF) ...............................................................................................................................................................................35
12.3 EVAPORATOR FAN OUTPUT (OAX =FAN) ...............................................................................................................................................................35
12.4 ALARM OUTPUT (OAX =ALR) ..................................................................................................................................................................................35
12.5 LIGHT OUTPUT (OAX =LIG)......................................................................................................................................................................................35
12.6 AUXILIARY OUTPUT (OAX =AUS) ............................................................................................................................................................................36
12.6.1 AUXILIARY REGULATOR ...............................................................................................................................................................................36
12.6.2 TIMED ACTIVATION......................................................................................................................................................................................36
12.6.3 GENERAL NOTES...........................................................................................................................................................................................36
12.7 DEAD BAND REGULATION (OAX =DB).....................................................................................................................................................................36
12.8 ON/OFF OUTPUT (OAX =ONF).................................................................................................................................................................................36
12.9 ENERGY SAVING OUTPUT (OAX =HES)...................................................................................................................................................................36
12.10 CONDENSER FAN OUTPUT (OAX =CND) .................................................................................................................................................................36
12.11 SECOND COMPRESSOR OUTPUT (OAX =CP2)........................................................................................................................................................36
12.12 SECOND DEFROST OUTPUT (OAX =DF2) ................................................................................................................................................................36
12.13 HEATER OUTPUT (OAX =HET) .................................................................................................................................................................................36
12.14 INVERTER OUTPUT (OAX =INV)...............................................................................................................................................................................36

1592040010 XRi30-31T EN v1.2 2020.08.26 XRi30T-XRi31T 4/42
13. DIGITAL INPUTS............................................................................................................................................................................................................37
13.1 DOOR SWITCH (IXF=DOR).........................................................................................................................................................................................37
13.2 START DEFROST (IXF=DEF) ......................................................................................................................................................................................37
13.3 AUXILIARY OUTPUT (IXF=AUS) ...............................................................................................................................................................................37
13.4 ENERGY SAVING (IXF=ES)........................................................................................................................................................................................37
13.5 EXTERNAL WARNING ALARM (IXF=EAL) ................................................................................................................................................................37
13.6 EXTERNAL LOCK ALARM (IXF=BAL) .........................................................................................................................................................................37
13.7 EXTERNAL PRESSURE ALARM (IXF=PAL) ................................................................................................................................................................37
13.8 EVAPORATOR FAN MODE (IXF=FAN)......................................................................................................................................................................37
13.9 REMOTE HOLIDAY MODE (IXF=HDF) ......................................................................................................................................................................37
13.10 REMOTE ONOFF (IXF=ONF) .....................................................................................................................................................................................37
13.11 LIGHT OUTPUT (IXF=LIG).........................................................................................................................................................................................37
13.12 CHANGE CONFIGURATION (IXF=CC) ......................................................................................................................................................................37
13.13 MOTION SENSOR DETECTOR (IXF=EMT) ................................................................................................................................................................37
14. ANALOGUE OUTPUTS ..................................................................................................................................................................................................38
14.1 2AO ANALOGUE OUTPUT CONFIGURATION –ONLY FOR XRI31T ........................................................................................................................38
15. ALARM SIGNALLING.....................................................................................................................................................................................................38
15.1 ALARM RECOVERY ..................................................................................................................................................................................................38
16. SERIAL COMMUNICATION ..........................................................................................................................................................................................38
17. INSTALLATION AND MOUNTING ................................................................................................................................................................................39
18. WIRING DIAGRAM .......................................................................................................................................................................................................39
18.1 XRI30T......................................................................................................................................................................................................................39
18.2 XRI31T......................................................................................................................................................................................................................39
19. TECHNICAL SPECIFICATIONS .......................................................................................................................................................................................40
20. APPENDIX .....................................................................................................................................................................................................................41
20.1 TOOLS......................................................................................................................................................................................................................41
20.1.1 XH-REP ..........................................................................................................................................................................................................41
20.1.2 X-MOD...........................................................................................................................................................................................................41
20.1.3 WIZMATE ......................................................................................................................................................................................................41
20.1.4 HOTKEY .........................................................................................................................................................................................................41
20.1.5 USB TO RS485 CONVERTER .........................................................................................................................................................................41
20.1.6 CABLES FOR VARIABLE SPEED COMPRESSORS AND VENTILATORS ..........................................................................................................41
20.2 EXAMPLE OF MENU NAVIGATION AND PARAMETER MODIFICATION................................................................................................................42

1592040010 XRi30-31T EN v1.2 2020.08.26 XRi30T-XRi31T 5/42
1. IMPORTANT USER INFORMATION
•The symbol is intended to alert the user of a non-insultated voltage source within the
product area that is sufficiently high to constitute a risk of electric shock to persons.
•The symbol is intended to alert the user of important operating and maintenance
(servicing) instructions.
•Dixell Srl reserves the right to modify this user’s manual at any time without prior notice. The
documentation can bedownloaded fromthe website www.fulltouch.info, evenpriorto purchase.
•This manual is an integral part of the product and must always be kept near the device for easy
and quick reference. The product cannot be used as a safety device. Please read this manual
very carfully be sure you understand the information provided before using the device.
•Verify that the power supply voltage is correct before connecting the device. Do not expose it to
water orhumidity: use the controlleronly within the operating limits, avoiding sudden temperature
changes and high atmospheric humidity in order to prevent condensation from forming.
Recommendations: disconnect all the electrical connections before performing any maintenance
task; insertthe probe where itcannotbe reachedby the End User; the device mustnotbe opened;
consider the maximum current that can be applied to each relay; make sure that the wires of the
probes, of the loads and the electical power supply cables are sufficiently separated from each
other, without crossing or intertwining. In case of applications in industrial environments, it may
be useful to use the main filters as well as the inductive loads.
•The customer shall bear full responsibility and risk for product configuration in order to achieve
the the final installation of the equipment/system. Upon the customer’s request and following a
specific agreement, Dixell Srlmaybe present during the start-up of the final machine/application,
as a consultant, however, under no circumstances can the company be held responsible for the
correct operation of the final equipment/system.
•Since Dixell products are part of a high-level technology, a qualification and a
configuration/programming/commissioning stage is required to best use them. Otherwise, these
products may malfunction and Dixell cannot be held responsible. The product must not be used
in any way that differs from that stipulated in the documentation.
•The device must always be installed inside an electrical panel that can only be accessed by
authorised personnel. For safety purposes, the keyboard must be the only part that can be
reached.
•The electrical wiring connections must never be modify while the device is being used.

1592040010 XRi30-31T EN v1.2 2020.08.26 XRi30T-XRi31T 6/42
•It is good practice to bear in mind the following indications for all Dixell products:
oPrevent the electronic circuits from getting wet as contact made with water, humidity or any
other type of liquid can damage them. Comply with the temperature and humidity limits
specified in the manual in order to store the product correctly.
oThe device must not be installed in particularly hot environments as high temperatures can
damage the electronic circuits and/or plastic components forming part of the casing. Comply
with the temperature and humidity limits specified in the manual in order to store the product
correctly.
oUnder no circumstances is the device to be opened –the user does not need any internal
component. Please contact qualified service personnel for any assistance.
oPrevent the device from being dropped, knocked or shaken as either can cause irreparable
damage.
oDo not clean the device with corrosive chemical products, solvents or aggressive detergents.
oThe device must not be used in applications that differ from that specified in the following
document.
•Separate the power supply of the device from the rest of the electrical devices connected
inside the electrical panel. The secondary of the transformer must never be connected to
the earth.
•Dixell Srl reserves the right to change the components of its products, even without notice,
ensuring the same and unchanged functionality.
2. PRODUCT DISPOSAL (WEEE)
In compliance with the Directive 2002/96/EC of the European Parliament and of the Council of January 27th
2003 and to the relative national legislation, please note that:
•There lies the obligation not to dispose of electrical and electronic waste as municipal waste
but to separate the waste.
•Public or private collection points must be used to dispose of the goods in accordance with
local laws. Furthermore, at the end of the product’s life, it is also possible to return this to the
retailer when a new purchase is made.
•This equipment may contain hazardous substances. Improper use or incorrect disposal can
have adverse effects on human health and the environment.
•The symbol shown on the product or the package indicates that the product has been placed
on the market after August 13th 2005 and must be disposed of as separated waste.
•Should the product be disposed of incorrectly, sanctions may be applied as stipulated in
applicable local regulations regarding waste disposal.
Please consider the environment before printing this manual.

1592040010 XRi30-31T EN v1.2 2020.08.26 XRi30T-XRi31T 7/42
3. GENERALITIES
The XRi3xT (x=0, 1) is a microprocessor-based controller suitable for applications on medium or low
temperature ventilated refrigeration units where variable speed compressor or ventilators are used. It has 2
relay outputs to control fans, light, defrost or auxiliary outputs. The device is also provided with up to 4 NTC,
PTC or PT1000 probe inputs. There are up to 2 configurable digital inputs. By usingthe HOT-KEY it is possible
to program the device quickly and easily. The controller implements Full Touch technology.
A special cable must be usedto connect variable speedcompressors driven by aninverter (only thefrequency-
based inverters are supported) and/or variable speed ventilators (only 0-10Vdc controlled ventilators are
supported).
3.1 USEFUL INFORMATION
Stay tuned on www.fulltouch.info
CONTACT: [e-mail]
4. USER INTERFACE
XRi3xT has a capacitive user interface with Full
Touch technology. The whole display area is
used to interact with the device. Specific gestures
are used to enable or disable functions, browse
through screens and operational modes and
modify the configuration of the device.
4.1 SCREENS
SCREEN
DESCRIPTION
Home: this screen shows temperature value,
measurement unit and active alarms only. This is the
first screen after power on or after exit from other status.
Virtual Keyboard: this screen shows available
functions. Activated function will blink when this screen
is visualized.
Info: This screen shows activated functions and
regulation outputs (compressor, ventilators).
Programming Mode: This screen enables the
modification of the Set Point or parameters.

1592040010 XRi30-31T EN v1.2 2020.08.26 XRi30T-XRi31T 8/42
Setpoint Menu: This screen enables the modification of
the Set Point value.
Parameter Menu: These screens enable the
modification of all parameter values.
Stand-By: in this condition all outputs are deactivated.
HotKey Download: “PRG” blinks during download
operations (copy from HotKey to the internal memory).
HotKey Upload: “PRG” blinks during upload operations
(copy from internal memory to the HotKey).
X9: it is possible to create the label of the parameter to
be visualized or modified.
4.2 ICONS
DESCRIPTION
MODE
FUNCTION
LIGHT
OFF
Function not available
FLASH
When in the Virtual Keyboard screen: light output ON
ON
When in the Virtual Keyboard screen: light output OFF
COMPRESSOR
OFF
When in the Loads Info screen: compressor output OFF
FLASH
Anti short cycle delay is running
ON
When in the Loads Info screen: compressor output ON
FAN
OFF
When in the Loads Info screen: evaporator fan output OFF
FLASH
Activation delay is running
ON
When in the Loads Info screen: evaporator fan output ON
DEFROST
OFF
Function not available
FLASH
When in the Virtual Keyboard screen: defrost ON
ON
When in the Virtual Keyboard screen: defrost OFF
AUX
OFF
Function not available
FLASH
When in the Virtual Keyboard screen: AUX output ON
ON
When in the Virtual Keyboard screen: AUX output OFF

1592040010 XRi30-31T EN v1.2 2020.08.26 XRi30T-XRi31T 9/42
4.3 GESTURES
GESTURE
NAME
HOW-TO
DESCRIPTION
ONE TAP
Press a specific area
of the screen with a
finger for 1 sec
Switch ON / Switch OFF: when in Virtual
Keyboard, use this to turn on/off a specific
function. When in Programming mode, use this to
select a parameter or a parameter value.
ENERGY SAVING
OFF
Function not available
FLASH
When in the Virtual Keyboard screen: energy saving ON
ON
When in the Virtual Keyboard screen: energy saving OFF
PULL DOWN
OFF
Function not available
FLASH
When in the Virtual Keyboard screen: pull down ON
ON
When in the Virtual Keyboard screen: pull down OFF
ALARM
OFF
No alarm is active
FLASH
ON
Some alarm is active
Celsius Degree
OFF
Not used
FLASH
Not used
ON
Measurement units: Celsius degree
Fahrenheit Degree
OFF
Not used
FLASH
Not used
ON
Measurement units: Fahrenheit degree
ONOFF
OFF
FLASH
ON
Only and always ON icon when the device is in standby mode
PROG LEVEL 1
OFF
FLASH
PROG LEVEL 1 and PROG LEVEL 2 icons toggle when the visualized value is
editable
ON
First level (parameter groups) of the parameter menu is visualized
PROG LEVEL 2
OFF
FLASH
PROG LEVEL 2 and PROG LEVEL 1 icons toggle when the visualized value is
editable
ON
Second level (parameter labels) of the parameter menu is visualized
RADIO ON
OFF
Not used
FLASH
Not used
ON
Not used
PROGRAMMING
MODE
OFF
Programming mode disabled
FLASH
ON
Programming mode enabled
BACK
OFF
FLASH
ON
Used to go back to previous levels on the menu tree
ENTER
OFF
Set point menu disabled
FLASH
ON
Set point menu enabled
BROWSING
OFF
No other (lateral) screens available
FLASH
ON
Other (lateral) screens available

1592040010 XRi30-31T EN v1.2 2020.08.26 XRi30T-XRi31T 10/42
TAP and
HOLD
Press any place of
the screen with a
finger for 3 sec
Enter / Save: use this to enter Programming
mode or Parameter menu and to save
modifications. When in Virtual Keyboard, use this
on the “ONOFF” to switch OFF and ON the
device.
H-SWIPE
Drag a finger across
the screen, from left
to right or from right
to left
Browse: use horizontal swipe (right to left or left
to right) to browse through HOME, Virtual
Keyboard and Info View. When in programming
mode: use horizontal swipe to browse through
parameter menu.
V-SWIPE
Drag a finger across
the screen, from top
to bottom or from
bottom to top
(overlapping only one
of the digits)
Modify: use vertical swipe (from top to bottom or
bottom to top) to change a parameter value.
4.4 HOME BROWSING
Use H-SWIPE to move through the screens. The logic implements a circular browsing: H-SWIPE to left or to
right is possible. A programmable timeout is implemented to return HOME from any lateral screen.
4.5 STAND-BY MODE
When in HOME screen, H-swipe to go to the Virtual Keyboard screen and then touch the OFF icon for 3 sec.
All outputs and alarms are deactivated in Stand-by mode.
4.6 PROGRAMMING MENU
It is possible to unlock the programming menu by touching any area of the display for 3 sec. Both SET and
PRG icons will blink until the programming menu is unlocked.
4.7 SETPOINT MENU
When in Programming Menu, it is possible to enter the Setpoint Menu by touching the SET icon for 3 sec.
Both SET and PRG icons will blink until the Setpoint Menu is unlocked. Both PROG LEVEL icons start
toggling to indicate that the visualized value is editable. Press the BACK icon to exit (come back to the
Programming Menu) without saving.

1592040010 XRi30-31T EN v1.2 2020.08.26 XRi30T-XRi31T 11/42
4.8 HOTKEY –UPLOAD
When in Programming Menu, it is possible to activate the HotKey Upload Menu function to save the current
device configuration (parameter values) into the external memory. To do this, follow these instructions:
1. H-swipe to go on the UPL screen
2. Insert the HotKey (on the 5-pin ports on the back of the device)
3. Touch the PRG icon for 3 sec
4. The copying procedure will start and the PRG icon will blink during the copy operations
5. At the end of the copying procedure, a message will notify the user that the operation has been
competed successfully:
a. End: all parameters have been copied
b. Err: some error occours during copying operations
4.9 HOTKEY –DOWNLOAD
When in Power-off or in Stand-by mode, it is possible to activate the HotKey Download Menu function to
copy a new configuration (parameter values) into the current device memory. To do this, follow these
instructions:
1. Insert the HotKey (on the 5-pin ports on the back of the device)
2. Touch the OFF icon for 3 sec
3. After power-on, the copying procedure will start automatically and the PRG icon will blink during the
copy operations
4. At the end of the copying procedure, a message will notify the user that the operation has been
competed successfully:
a. End: all parameters have been copied
b. Err: some error occours during copying operations
4.10 X9
Every parameter is normally identified by a unique label that can have two or three alphanumeric characters.
When in “X9” Screen, it is possible to create the parameter label by swiping-up every single part of the label
(first, second and third char). The system is able to drive the user through the symbols, showing only the
available ones to speed up the creation of the label.
For example, if a modification of the “interval between defrosts” parameters is required (label “idF”), these are
the steps to follow:
- Enter the X9 Screen
- Swipe-up or down the first char position (lower segment on the left) until char “i” (lower case) appears
- Move tothe second char position (segment inthe middle) and swipe-up or down until char “d” appears
- Move to the third char position (segment on the right) and swipe-up or down until char “F” appears
- Enter the par. value by touching the PRG icon for 3 sec.

1592040010 XRi30-31T EN v1.2 2020.08.26 XRi30T-XRi31T 12/42
NOTE: pay attention to the upper or lower case when browsing through the available characters.
For simplicity, here is the complete list of available characters: A, b, C, d, E, F, G, H, i, L, M, n, o, P, q, r, S, t,
u, V, Y, 0, 1, 2, 3, 4, 5, 6, 7, 8 and 9.
4.11 PARAMETER MENU
When in Programmin Menu, it is possible to enter the Parameter Menu by touching the PRG icon for 3 sec.
The Prog Level 1 icon will indicate the first level of the programming menu (group labels).
The Browsing icon will indicate that there are other groups of parameters.
…
When in PROG LEVEL 1, it is possible to browse through the available groups of parameters by using the H-
swipe gesture. The circular construction of this menu allows to move left or right through the groups.
Here are the available groups:
Group Label
Description
rEG
Main regulation parameters
Prb
Probe configuration parameters
VSC
Variable Speed Compressor parameters
diS
Visualization parameters
dEF
Defrost configuration parameters
FAn
Evaporator and condenser fan configuration parameters
AUS
Auxiliary regulator parameters
ALr
Alarm configuration parameters
oUt
Digital and analogue output configuration parameters
inP
Digital input configuration parameters
ES
Energy saving configuration parameters
Cnt
Counters, read only values
rtC
Real Time Clock configuration parameters
E2
Memory storage management
CoM
Serial Communication port configuration parameters
Ui
User Interface configuration parameters
inF
Information, read only parameters
PAS
Password for entering protected menu parameters
4.12 PASSWORD MENU

1592040010 XRi30-31T EN v1.2 2020.08.26 XRi30T-XRi31T 13/42
When in the PAS group, it is possible to set the password value by touching the PRG icon for 3 sec.
V-swipe on a single digit to modify the value, then confirm the password value by touching the PRG icon for
3 sec.
The new value will blink and after 2 sec the display will show:
•Pr2 if the password is correct
•Err if the password value is wrong
After 2 sec the display will show the first group label (rEG) with a blinking PRG icon to indicate that protected
parameters now are editable.
5. PARAMETER TABLE
Here are the descriptions of the device parameters.
5.1 PARAMETER DESCRIPTION
5.1.1 Main regulation parameters - rEG
SEt
Set Point: range from LS to US
LS
Minimum Set Point: (-100.0°C to SET; -148°F to SET) fix the minimum value for the set point.
US
Maximum Set Point: (SET to 200.0°C; SET to 392°F) fix the maximum value for the set point.
HY
Compressor regulation differential in normal mode: (0.1 to 25.0°C; 1 to 45°F) set point
differential. Compressor Cut-IN is T > SET + HY. Compressor Cut-OUT is T<=SET.
HYE
Compressor regulation differential in energy saving mode: (0.1 to 25.0°C; 1 to 45°F) set point
differential. Compressor Cut-IN is T > SET + HES + HYE. Compressor Cut-OUT is T<= SET + HES.
odS
Output activation delay at start-up: (0 to 255 min) this function is enabled after the instrument
power-on and delays the output activations.
AC
Anti-short cycle delay: (0 to 50 min) minimum interval between a compressor stop and the
following restart.
rtr
Regulation percentage=F(P1; P2) (100=P1; 0=P2): 100=P1 only; 0=P2 only
CCt
Maximum duration for Pull Down: (0.0 to 23h50min, res. 10min) after elapsing this time interval,
the super cooling function is immediately stopped.
CCS
Pull Down phase differential (SET+CCS or SET+HES+CCS): (-12.0 to 12.0°C; -21 to 21°F) during
any super cooling phase the regulation SETPOINT is moved to SET+CCS (in normal mode) or to
SET+HES+CCS (in energy saving mode)
oHt
Threshold for automatic activation of Pull Down in normal mode (SET+HY+oHt): (1.0 to 12.0°C;
1 to 21°F) this is the upper limit used to activate the super cooling function.
oHE
Threshold for automatic activation of Pull Down in energy saving mode
(SET+HES+HYE+oHE): (1.0 to 12.0°C; 1 to 21°F) this is the upper limit used to activate the super
cooling function.
Con
Compressor ON time with faulty probe: (0 to 255 min) time during which the compressor is active
in case of faulty thermostat probe. With CY=0 compressor is always OFF.
CoF
Compressor OFF time with faulty probe: (0 to 255 min) time during which the compressor is OFF
in case of faulty thermostat probe. With Cn=0 compressor is always active.
5.1.2 Probe configuration parameters –Prb
P1C
Probe P1 selection: (ntC; PtC; Pt1) ntC=NTC type; PtC=PTC type; Pt1=PT1000 type
P2C
Probe P2 selection: (ntC; PtC; Pt1) ntC=NTC type; PtC=PTC type; Pt1=PT1000 type
P3C
Probe P3 selection: (ntC; PtC; Pt1) ntC=NTC type; PtC=PTC type; Pt1=PT1000 type
P4C
Probe P4 selection: (ntC; PtC; Pt1) ntC=NTC type; PtC=PTC type; Pt1=PT1000 type
ot
Probe P1 calibration: (-12.0 to 12.0°C; -21 to 21°F) allows to adjust any possible offset of the first
probe.

1592040010 XRi30-31T EN v1.2 2020.08.26 XRi30T-XRi31T 14/42
P2P
Probe P2 presence: n= not present; Y= present.
oE
Probe P2 calibration: -12.0 to 12.0°C; -21 to 21°F) allows to adjust any possible offset of the
second probe.
P3P
Probe P3 presence: n= not present; Y= the defrost is present.
o3
Probe P3 calibration: (-12.0 to 12.0°C; -21 to 21°F) allows to adjust any possible offset of the third
probe.
P4P
Probe P4 presence: n= not present; Y= present.
o4
Probe P4 calibration: (-12.0 to 12.0°C; -21 to 21°F) allows to adjust any possible offset of the forth
probe.
5.1.3 Variable Speed Compressor parameters - VSC
HY1
Variable Speed Compressor Differential in normal mode: 0.1 to 25.5°C; 1 to 45°F
HYS
Variable Speed Compressor Differential in energy saving mode: 0.1 to 25.5°C; 1 to 45°F
FMi
Minimum value for Variable Speed Compressor (RPM * 10): (0 to FMA) select according to the
VSC in use
FMA
Maximum value for Variable Speed Compressor (RPM * 10): (FMi to 500) select according to
the VSC in use
Fr0
Value when Variable Speed Compresso is shut-down (RPM * 10): (0 to 200) select according
to the VSC in use
tSt
PI regulator, temperature sampling time: (00:00 to 42min:30sec)
iSt
PI regulator, integral sampling time: (00:00 to 42min:30sec)
vdC
Type of Variable Speed Drive: (nu; FrE) nu = no VSC in use; FrE = VSC with frequency control
mode is used
voS
Signal output variation for Variable Speed Compressor: (1 to 255 Hz) VSC variation when
SET-HY ≤ T ≤ SET+HY
vo2
Signal output variation for Variable Speed Compressor: (1 to 255 Hz) VSC variation when
SET-HY-HY1≤T<SET-HY and SET+HY<T≤SET+HY+HY1
vo3
Signal output variation for Variable Speed Compressor: (1 to 255 Hz) VSC variation when
SET-HY-HY1<T and T>SET+HY+HY1
PdP
Variable Speed Compressor (in %) during any Pull Down: (0 to 100%)
SPi
Compressor speed (in %) in case of any probe error during Con interval: (0 to 100%)
Aod
Compressor speed (in %) during any defrost cycle (valid if tdf=in): (0 to 100%)
AoF
Compressor speed (in%) during a pre-defrost phase (valid if tdf=in): (0 to 100%)
CMn
Continuous control ON in normal mode: (n;Y) Y= VSC is never stopped during regulation
CME
Continuous control ON in energy saving mode: (n;Y) Y= VSC is never stopped during
regulation
MnP
Compressor speed threshold to activate lubrication (valid for variable speed compressors
only, 0=disabled): (nu; 1 to 100%; OFF) nu = not used; 1 to 100% = select the percentage to
activate function; OFF = compressor is stopped when the condition is reached
tMi
Time range with compressor speed below MnP to activate lubrication cycle: (00:00 to
24h00min) time before activating the lubrication function
tMA
Time range with compressor speed at 100% to activate lubrication cycle: (0 to 255 min) VSC
will be forced to 100%, for tMA, after activating the lubrication function. NOTE: if MnP=OFF, VSC
will be stopped for tMA
5.1.4 Visualization parameters –diS
CF
Temperature measurement unit: (°C; °F) °C = Celsius; °F = Fahrenheit.
rES
Temperature resolution: (dE; in) dE = decimal; in = integer.
Lod
Probe default displayed: (P1; P2; P3; P4; Set; dtr; Usr) Px=probe “x”; Set=set point; dtr=do not
use it.
rEd
Remote probe displayed (for XH-REP): (P1; P2; P3; P4; Set; dtr; Usr) Px=probe “x”; Set=set
point; dtr=do not use it.
dLY
Temperature display delay: (0.0 to 20min00sec, res. 10 sec) when the temperature increases, the
display is updated of 1°C or 1°F after this time.
dtr
Probe visualization percentage, F(P1; P2): (0 to 100) with dtr=1 the display will show this value
VALUE=0.01*P1+0.99*P2
5.1.5 Defrost configuration parameters –dEF
EdF
Defrost mode: in=fixed intervals; rtC=following real time clock
tdF
Defrost type: EL=electrical heaters; in=hot gas

1592040010 XRi30-31T EN v1.2 2020.08.26 XRi30T-XRi31T 15/42
dFP
Probe selection for defrost control: (nP; P1; P2; P3; P4) nP=no probe; Px=probe “x”. Note:
P4=Probe on Hot Key plug.
dtE
End defrost temperature: (-55 to 50°C; -67 to 122°F) sets the temperature measured by the
evaporator probe (dFP), which causes the end of defrost cycle.
idF
Interval between two consecutive defrost cycles: (0 to 255 hours) determines the time interval
between the beginning of two defrosting cycles.
MdF
Maximum length of defrost cycle: (0 to 255 min; 0 means no defrost) when P2P=n (no
evaporator probe presence) it sets the defrost duration, when P2P=Y (defrost end based on
evaporator temperature) it sets the maximum length for the defrost cycle.
dSd
Start defrost delay: (0 to 255 min) delay in defrost activation.
StC
Compressor stop before starting any defrost: (0 to 900 sec) interval with compressor OFF
before activating hot gas cycle
dFd
Display during defrost: (rt; it; SP; dF) rt = real temperature; it = start defrost temperature;
SP = SET-POINT; dF = label “dF”.
dAd
Temperature display delay after any defrost cycle: (0 to 255 min) delay before updating the
temperature on the display after the end of any defrost.
Fdt
Draining time: (0 to 255 min) regulation delay after finishing a defrost phase
Hon
Drain heater enabled after draining time (par. Fdt): (0 to 255 min) the relative output will stay on
after draining time.
dPo
Defrost cycle enebled at stat-up: (n; Y) enables defrost at power on.
HYP
Differential temperature during any pre-defrost phase: (-12.0 to 12.0°C; -21 to 21°F)
Pd2
Defrost output deactivation delay: (0 to 255 sec)
dAF
Pre-defrost time: (0 to 255 min)
od1
Automatic defrost (at the beginning of any energy saving mode): (n; Y) n=function disabled;
Y=function enabled
od2
Optimized defrost: (n;Y) n= function disabled; Y= the controller needs a temperature probe
placed on the evaporator surface to monitor the presence of ice during any defrost phase.
dSt
Temperature sampling time during an optimized defrost (valid only if od2=yes): (1 to 255
sec) interval used to analyze the evaporator temperature and define the defrost phase
SYd
Type of synchronized defrost: (n; SYn; nSY) n = function disabled; SYn = synchronized, all
devices connected will start a defrost phase at the same time. nSY = de-synchronized, all devices
connected will delay the beginning of the same defrost phase.
dt1
Differential temperature for latent heating control (0.1 to 1.0 °C) to catch the latent heating
phase during any defrost
ErS
Restart regulation after dripping time, when defrost Syd = nSY: n = disabled; Y= enabled
5.1.6 Evaporator and condenser fan configuration parameters –Fan
FAP
Probe selection for evaporator fan: (nP; P1; P2; P3; P4) nP=no probe; Px=probe “x”. Note:
P4=Probe on Hot Key plug.
FSt
Evaporator fan stop temperature: (-55 to 50°C; -67 to 122°F) setting of temperature, detected by
evaporator probe. Above this temperature value fans are always OFF. NOTE: it works only for
the evaporator fan, NOT for the condenser fan.
HYF
Evaporator fan regulator differential: (0.1 to 25.5°C; 1 to 45°F) evaporator fan will stop when the
measured temperature (from FAP) is T<FSt-HYF.
FnC
Evaporator fan operating mode: (Cn; on; CY; oY)
•Cn = runs with the compressor, duty-cycle when compressor is OFF (see FoF,Fon, FF1 and
Fo1 parameters) and OFF during defrost
•on = continuous mode, OFF during defrost
•CY = runs with the compressor, duty-cycle when compressor is OFF (see FoF,Fon, FF1 and
Fo1 parameters) and ON during defrost
•oY = continuous mode, ON during defrost
Fnd
Evaporator fan delay after defrost cycle: (0 to 255 min) delay before fan activation after any
defrosts.
FCt
Differential for cyclic activation of evaporator fans: (0 to 50°C)
FSU
Evaporator fan operating mode: (Std; Fon; FoF) Std = standard mode, evaporator fan uses par
FnC; Fon = evaporator Fan always on; FoF = evaporator fan always off.
Ft
Evaporator fan controlled during defrost: (n; Y) n= evaporator fan uses par. FnC during any
defrost; Y= evaporator fan regulator is active during any defrost.
Fon
Evaporator fan ON time in normal mode (with compressor OFF): (0 to 255 min) used when
energy saving status is not active.

1592040010 XRi30-31T EN v1.2 2020.08.26 XRi30T-XRi31T 16/42
FoF
Evaporator fan OFF time in normal mode (with compressor OFF): (0 to 255 min) used when
energy saving status is not active.
Fo1
Evaporator fan ON time in energy saving mode (with compressor OFF) (0 to 255 min) used
when energy saving status is active.
FF1
Evaporator fan OFF time in energy saving mode (with compressor OFF): (0 to 255 min) used
when energy saving status is active.
Fd1
Evaporator fan delay: (0 to 255 sec) delay before activating evaporator fan
Fd2
Evaporator fan delay after closing door: (0 to 255 sec) delay before activating evaporator fan
and after closing the door
FAC
Probe selection for condenser fan: (nP; P1; P2; P3; P4) nP=no probe; Px=probe “x”. Note:
P4=Probe on Hot Key plug.
St2
Set Point 2 regulation (for condenser fan): (-55 to 50°C; -67 to 122°F) setting of temperature
detected by evaporator probe. Above this value of temperature fans are always OFF.
HY2
Set Point 2 differential (for condenser fan): (0.1 to 25.5°C; 1 to 45°F) differential for evaporator
ventilator regulator
FCC
Condenser fan operating mode: (Cn; on; CY; oY)
•Cn = runs with the compressor and OFF during defrost
•on = continuous mode, OFF during defrost
•CY = runs with the compressor and ON during defrost
•oY = continuous mode, ON during defrost
Fd3
Condenser fan activation delay: (0 to 255 sec) delay before activating condenser fan
Fd4
Condenser fan deactivation delay: (0 to 255 sec) delay before deactivating condenser fan
5.1.7 Auxiliary regulator parameters –AUS
ACH
Type of control for auxiliary regulator: (Ht; CL) Ht = heating; CL = cooling.
SAA
Set Point for auxiliary regulator: (-55.0 to 150.0°C; -67 to 302°F) it defines the room
temperature set point to switch auxiliary relay.
SHY
Auxiliary regulator differential: (0.1 to 25.5°C; 1 to 45°F) differential for auxiliary output set
point.
•ACH=CL, AUX Cut in is [SAA+SHY]; AUX Cut out is SAA.
•ACH=Ht, AUX Cut in is [SAA–SHY]; AUX Cut out is SAA.
ArP
Probe selection for auxiliary regulator: (nP; P1; P2; P3; P4) nP = no probe, the auxiliary relay
is switched only by the digital input; Px=probe “x”. Note: P4=Probe on Hot Key plug.
Sdd
Auxiliary regulator disabled during any defrost cycle: (n; Y) n= the auxiliary relay operates
during defrost. Y= the auxiliary relay is switched off during defrost.
btA
Base time for parameters Ato and AtF: (SEC; Min) SEC = base time is in seconds; Min =
base time is in minutes.
Ato
Time interval with auxiliary output ON: 0 to 255 (base time defined in par. btA)
AtF
Time interval with auxiliary output OFF: 0 to 255 (base time defined in par. btA)
2oL (*)
Minimum value for analogue output 2: (0 to 100%) minimum value for 0-10Vdc output
2oH (*)
Maximum value for analogue output 2 (0 to 100%) maximum value for 0-10Vdc output
2At (*)
Time interval with analogue output 2 (maximum value) (0 to 255 sec) analogue output is
forced at 100%, after any activation, for 2At seconds.
(*) Available only for XRi31T
5.1.8 Alarm configuration parameters
ALP
Probe selection for temperature alarms: (nP; P1; P2; P3; P4) nP=no probe; Px=probe “x”. Note:
P4=Probe on Hot Key plug.
ALC
Temperature alarm configuration: (Ab, rE) Ab = absolute; rE = relative.
ALU
High temperature alarm: when this temperature is reached, the alarm is enabled after the Ad
delay time.
•If ALC=Ab →ALL to 150.0°C or ALL to 302°F.
•If ALC=rE →0.0 to 50.0°C or 0 to 90°F.
ALL
Low temperature alarm: when this temperature is reached, the alarm is enabled after the Ad
delay time.
•If ALC=Ab →-55.0°C to ALU or -67°F to ALU.
•If ALC=rE →0.0 to 50.0°C or 0 to 90°F.
AFH
Temperature alarm differential: (0.1 to 25.0°C; 1 to 45°F) alarm differential.

1592040010 XRi30-31T EN v1.2 2020.08.26 XRi30T-XRi31T 17/42
ALd
Temperature alarm delay: (0 to 255 min) delay time between the detection of an alarm condition
and the relative alarm signalling.
dot
Temperature alarm delay with open door: (0.0 to 24h00min, res. 10 min) delay time between the
detection of a temperature alarm condition and the relative alarm signalling, after starting up the
instrument.
dAo
Temperature alarm delay at start-up: (0.0 to 24h00min, res. 10 min) delay time between the
detection of a temperature alarm condition and the relative alarm signalling, after starting up the
instrument.
AP2
Probe selection for second temperature alarm: (nP; P1; P2; P3; P4) nP=no probe; Px=probe
“x”. Note: P4=Probe on Hot Key plug.
AU1
Pre-alarm threshold for second temperature alarm (absolute value): (-55.0 to 150.0°C; -67 to
302°F)
AH1
Second high temperature pre-alarm differential: (0.1 to 25.0°C; 1 to 45°F)
Ad1
Second high temperature pre-alarm delay: (0 to 255 min; 255 = not used) delay time between
the detection of a condenser pre-alarm condition and the relative alarm signalling.
AL2
Second low temperature alarm: (-55.0 to 150.0°C; -67 to 302°F)
AU2
Second high temperature alarm: (-55.0 to 150.0°C; -67 to 302°F)
AH2
Second temperature alarm differential: (0.1 to 25.0°C; 1 to 45°F)
Ad2
Second temperature alarm delay: (0 to 255 min; 255 = not used) delay time between the
detection of a condenser alarm condition and the relative alarm signalling.
dA2
Second temperature alarm delay at start-up: (0.0 to 24h00min, res. 10 min)
bLL
Compressor OFF due to second low temperature alarm: (n; Y) n = no, the compressor
continues to work; Y = yes, the compressor is switched off while the alarm is ON; in any case, the
regulation restarts after AC time at minimum.
AC2
Compressor OFF due to second high temperature alarm: (n; Y) n = no, the compressor
continues to work; Y = yes, the compressor is switched off while the alarm is ON; in any case, the
regulation restarts after AC time at minimum.
SAF
Differential for anti-freezing control: (-12.0 to 12.0°C; -21.0 to 21.0°F) the regulation stops if
T<SET+SAF
tbA
Alarm relay deactivation: (n; Y) n = no, it is not possible to deactivate neither the buzzer nor any
digital output set as an alarm; Y = yes, it is possible to deactivate both the buzzer and the digital
output set as an alarm.
5.1.9 Digital and analogue output configuration parameters - out
oAx
(x=1, 2)
Relay output oAx configuration: (nu; CP1; dEF; Fan; Alr; LiG; AUS; db; onF; HES; Cnd)
nu=not used; CP1=compressor; dEF=defrost; Fan=ventilators; Alr=alarm; LiG=light;
AUS=auxiliary relay; onF=always ON with instrument ON; db=neutral zone; HES=night
blinds; Cnd=condenser fan; CP2=second compressor; dF2=second defrost; Het=heater
control; inV=do not use it.
AoP
Alarm relay polarity: (oP; CL) oP = alarm activated by closing the contact; CL = alarm
activated by opening the contact
1Ao
Analogue output 1 configuration: (nu; FrE) nu = not used; FrE = frequency output with
duty cycle fixed at 50%.
2Ao (*)
Analogue output 2 configuration: (nu; tiM; FAn; AUS; ALr; Cnd; LiG; inV) nu = not used;
tiM = timed, the output will change between min and MAX value following Ato and AtF
value respectively; FAn = analogue output depends on the evaporator fan regulator; AUS =
analogue output depends on the auxiliary regulator; ALr = analogue output activated in
case of any alarm condition; Cnd = analogue output depends on the condenser fan
regulator; LiG = do not use it; inv = do not use it.
(*) Available for XRi31T only
5.1.10 Digital input configuration parameters - inP
ibt
Base time for digital inputs: (SEC; Min) SEC = seconds; Min = minutes. Delay in activating the
function linked to the digital inputs.
i1P
Digital input 1 polarity: (oP; CL) oP = activated by closing the contact; CL = activated by opening
the contact.

1592040010 XRi30-31T EN v1.2 2020.08.26 XRi30T-XRi31T 18/42
i1F
Digital input 1 configuration: (nu; dor; dEF; AUS; ES; EAL; bAL; PAL; FAn; HdF; onF; LiG; CC;
EMt)
•nu=not used
•dor = door switch function
•dEF = defrost activation
•AUS = auxiliary output
•ES = energy saving mode activation
•EAL = external warning alarm
•bAL = external lock alarm
•PAL = external pressure alarm
•FAn = evaporator fan control
•HdF = holiday defrost
•onF = ON/OFF status change
•LiG = light output control
•CC = change configuration (between C1 and C2)
•EMt = Motion sensor X-MOD
did
Digital input 1 alarm delay (base time depends on par. ibt): (0 to 255) delay between the
detection of an external event and the activation of the relative function.
i2P
Digital input 2 polarity: (oP; CL) oP = activated by closing the contact; CL = activated by opening
the contact.
i2F
Digital input 2 configuration: (nu; dor; dEF; AUS; ES; EAL; bAL; PAL; FAn; HdF; onF; LiG; CC;
EMt)
•nu = not used
•dor = door switch function
•dEF = defrost activation
•AUS = auxiliary output
•ES = energy saving mode activation
•EAL = external warning alarm
•bAL = external lock alarm
•PAL = external pressure alarm
•FAn = evaporator fan control
•HdF = holiday defrost
•onF = ON/OFF status change
•LiG = light output control
•CC = change configuration (between C1 and C2)
•EMt = Motion sensor X-MOD
d2d
Digital input 2 alarm delay (base time depends on par. ibt): (0 to 255) delay between the
detection of an external event and the activation of the relative function.
nPS
Number of external pressure switch alarms before stopping the regulation: (0 to 15) after
reaching nPS events in the digital input alarm delay (par. dxd), the regulation will be stopped and a
manual restart (ON/OFF, power OFF and power ON) will be required
odC
Compressor and fan status after door opening: (no; FAn; CPr; F-C): no = normal;
FAn = Fans OFF; CPr = Compressor OFF; F-C = Compressor and fans OFF.
rrd
Regulation restart after door alarm: (n; Y) n = no regulation if the door is open; Y = when the rrd
timer elapses, the regulation restarts even if a door open alarm is ON.
CLi
Light output activation from door input: (n; Y) the activation of a digital input set as ixF=dor
forces the light output ON.
LCi
Time with light output forced ON (0=function disabled): (0 to 255 min) interval with light output
forced ON from digital input ixF=dor.
n01
Number of motion detections before activating light output (valid if ixF=EMt): (0 to 10)
number of motion sensor detections before forcing the light output ON.
t01
Time with light output forced ON after motion detection: (0 to 255 min) interval with light output
forced ON from digital input ixF=Emt.
5.1.11 Energy saving configuration parameters - ES
ErA
Energy saving algorithm: (nu; bAS) nu=disabled, the energy saving mode activation is by button,
real time clock or digital input; bAS=basic algorithm, the energy saving mode activation depends
on the the digital input.

1592040010 XRi30-31T EN v1.2 2020.08.26 XRi30T-XRi31T 19/42
HES
Energy saving mode temperature differential: (-30.0 to 30.0°C; -54 to 54°F) sets the increasing
value of the set point during the Energy Saving cycle.
LdE
Energy saving controls the lights (lights OFF when energy saving is active): (n; Y) lights off
when energy saving mode is active
StE
Period to switch from normal mode to energy saving mode: (0.0 to 24h00min, res. 10 min) if
the door stay closed for StE time, the energy saving mode will be activated. NOTE: this will require
a door switch to work.
EtS
Period to switch from energy saving mode to normal mode: (0.0 to 24h00min, res. 10 min)
maximum time for energy saving mode. NOTE: this will require a door switch to work.
dS
Door open time to switch from EtS to StE: (0 to 999 sec) the energy saving mode will be
immediately deactivated as soon as the door stays open more than the dS time. NOTE: this will
require a door switch to work.
nES
Number of motion detections before disabling energy saving mode (valid if ixF=EMt): (0 to
255) number of motion sensor detections before disabling the energy saving mode.
5.1.12 Counters, read only values - Cnt
n1H
Number of activations for relay output oA1 (thousands of)
n1L
Number of activations for relay output oA1 (units of)
n2H
Number of activations for relay output oA2 (thousands of)
n2L
Number of activations for relay output oA2 (units of)
n5H
Number of total activation of digital input 1 (thousand of)
n5L
Number of total activation of digital input 1 (units of)
n6H
Number of total activation of digital input 2 (thousand of)
n6L
Number of total activation of digital input 2 (units of)
F1H
Number of working hours for relay output oA1 (thousands of)
F1L
Number of working hours for relay output oA1 (units of)
F2H
Number of working hours for relay output oA2 (thousands of)
F2L
Number of working hours for relay output oA2 (units of)
5.1.13 Real Time Clock configuration parameters - rtC
Hur
Hours: 0 to 23 hours
Min
Minutes: 0 to 59 minutes
dAY
Day of the week: Sun to Sat
dYM
Day of the month: 1 to 31
Mon
Month: 1 to 12
YAr
Year: 00 to 99
Hd1
First day of weekend: (Sun to SAt; nu) setting for the first day of the weekend.
Hd2
Second day of weekend: (Sun to SAt; nu) setting for the second day of the weekend.
iLE
Energy saving cycle start time on working days: (00h00min to 23h50min) during the Energy
Saving cycle, the set point is increased by the value in HES so that the operation set point is
SET+HES.
dLE
Energy saving cycle duration on working days: (00h00min to 24h00min) sets the duration of
the Energy Saving cycle on working days.
iSE
Energy saving cycle start time on weekends: 00h00min to 23h50min
dSE
Energy saving cycle duration on weekends: 00h00min to 24h00min
ddx
Daily defrost enabled: (n; Y) to enable the Ld1 to Ld6 defrost operations for any day of the
week.
•dd1 = Sunday defrost
•dd2 = Monday defrost
•dd3 = Tuesday defrost
•dd4 = Wednesday defrost
•dd5 = Thursday defrost
•dd6 = Friday defrost
•dd7 = Sunday defrost
Ldx
Defrost start time: (00h00min to 23h50min) these parameters set the beginning of the
programmable defrost cycles during any ddx day. Example: when Ld2=12.4, the second defrost
starts at 12:40 am during working days.

1592040010 XRi30-31T EN v1.2 2020.08.26 XRi30T-XRi31T 20/42
5.1.14 Memory storage management –E2
MAP
Current configuration: (C-1; C-2) to change configuration used.
LdM
Restore default factory settings: (n;Y) select Y and confirm to reload factory default values for
the configuration currently used.
rHA
Reset HACCP values: (n; Y) select Y and confirm to reset the memorized min and MAX
temperature values (HACCP function must be enabled).
5.1.15 Serial Communication port configuration parameters - CoM
Adr
Serial address: (1 to 247) device address for Modbus communication
bAU
Baudrate: (9.6; 19.2; 38.4; 57.6) select the correct baudrate for serial communication
PAr
Parity control: (no; odd; EvE) no=no parity control; odd=odd parity control; EvE=even parity
control
5.1.16 User Interface configuration parameters - Ui
SCS
User interface timeout: (1 to 255 sec) timeout before coming back to Home Screen or to
Programming Menu
bS
Sound Level: (0 to 5) select the sound level of the gestures
PSU
Password for protected level Pr2: (000 to 999) insert a value to protect all the parameters set
on the level Pr2 from modification
5.1.17 Information, read only parameters - inF
dP1
Probe P1 value visualization
dP2
Probe P2 value visualization
dP3
Probe P3 value visualization
dP4
Probe P4 value visualization
rSE
Real regulation Set Point
FdY
Firmware release date: day
FMt
Firmware release date: month
FYr
Firmware release date: year
rEL
Firmware release: progressive number
SUb
Firmware sub release: progressive number
Ptb
Parameter map version
5.2 PARAMETER CONFIGURATION 1
Group
Parameter
Description
Value
Protected
U.O.M.
Range
rEG
SEt
Set Point
3.0
Pr1
°C
LS to US
rEG
LS
Minimum Set point
-100.0
Pr1
°C
[-100.0°C to SET]
[-148.0°F to SET]
rEG
US
Maximum Set point
150.0
Pr1
°C
[SET to 150.0°C]
[SET to 302.0°F]
rEG
HY
Compressor regulation differential in
normal mode
3.0
Pr1
°C
[0.1°C to 25.0°C]
[0.1°F to 45.0°F]
rEG
HYE
Compressor regulation differential in
energy saving mode
3.0
Pr1
°C
[0.1°C to 25.0°C]
[0.1°F to 45.0°F]
rEG
odS
Output activation delay at start-up
0
Pr1
min
0 to 255 min
rEG
AC
Anti-short cycle delay
0
Pr1
min
0 to 50 min
rEG
rtr
Regulation percentage=F(P1; P2)
(100=P1; 0=P2)
100
Pr2
0 to 100
rEG
CCt
Maximum duration for Pull Down
00:00
Pr2
hh:mm
0 to 23h50min
rEG
CCS
Pull Down phase differential (SET+CCS or
SET+HES+CCS)
0.0
Pr2
°C
[-12.0°C to 12.0°C]
[-21.6°F to 21.6°F]
rEG
oHt
Threshold for automatic activation of Pull
Down in normal mode (SET+HY+oHt)
10.0
Pr2
°C
[0.0°C to 25.0°C]
[0.0°F to 45.0°F]
rEG
oHE
Threshold for automatic activation of Pull
Down in energy saving mode
(SET+HES+HYE+oHE)
10.0
Pr2
°C
[0.0°C to 25.0°C]
[0.0°F to 45.0°F]
rEG
Con
Compressor ON time with faulty probe
10
Pr1
min
0 to 255 min