Emerson F02/EPI2 User manual

F02/EPI2 Quarter-Turn
Electric Actuator
Base and OM1 Card
F02/EPI2 Base and OM1 Card
April 2018
Quick Start Guide
VCIOM-08536-US Rev. 0
Base Card
F02/EPI2 Quarter-Turn Electric Actuator
Figure 1 Model 063-125
Green LED
Power ON
Dip switch
SW3
Push button
SW5
Red LED
Enter configuration
Rotary switch
SW4
Rotary switch
SW6
Figure 2 Model 250-500-1000-2000
Dip switch
SW3
Green LED
Power ON
Rotary switch
SW6
Rotary switch
SW4
Red LED
Enter configuration
Push button
SW5
Table 1.
Operating Times
Model Nominal torque
(Nm/lb.in.)
Operating time (secs 90o) at selected step
8 6 4
063 63/600 15 28 48
125 125/1300 15 28 48
250 250/2500 15 28 48
500 500/5100 15 28 48
1000 1000/9100 24 45 80
2000 2000/17700 53 100 180
Note:
(*) Factory
PRE-INSTALLATION: See VCIOM-2881 INSTALLATION AND MAINTENANCE INSTRUCTIONS. Not performing the following procedures will invalidate the product warranty.
INSTALLATION: To assemble the actuator onto the valve proceed as follows:
a. Verify proper mounting hardware.
b. Verify proper electrical service to the actuator
c. Lubricate the valve stem with oil or grease to make the assembly easier: pay attention not to contaminate with lubricant the ange surfaces which transmit the actuator torque.
d. Clean the valve ange and remove anything that might prevent a perfect adherence to the actuator ange and especially all traces of grease.
e. Install the actuator onto the valve so that the shaft out put drive enters the groove of the stem extension. This coupling must take place without forcing and only with the weight of the
actuator.
f. Ensure actuator and valve are in same orientation when bolting together.
g. With the handwheel, operate the actuator to verify it moves the valve smoothly.
WARNING
The conguration must be done while the actuator is powered on. As a consequence, all conguration operations must be carried out by specically qualied personnel for operations on
powered electronic cards. Hazardous voltages may be present. Before connecting power to the actuator, check that the voltages are correct and according to the nameplate data. Improper power
supply will cause permanent damage to the electrical components. Actuator conguration programming requires removal of the actuator cover. Refer to VCIOM-2881 IOM for instructions.
Quick Start Guide
VCIOM-08536-US Rev. 0
F02/EPI2 Base and OM1 Card
April 2018
See
table 1
Rotary Switch Settings
Configurations
Move switch SW4 to position
indicated in each row
Move switch SW6 to position
indicated in each row SW3 Conrm by
SW5 Red LED
SW3
CLOSE LIMIT by position 2 1 (*)
Enter set up conguration moving SW3 to ON
PUSH
LED lights up once
Exit set up conguration moving SW3 to 1 (Run Setting)
Drive the actuator to
the CLOSE position
using the handwheel
0 0
OPEN LIMIT by position 3 1 (*) LED lights up once
Drive the actuator to
the OPEN position
using the handwheel
1 0
CLOSE LIMIT by torque 2 0 (*)
Operate the
actuator to direction
bylocal/remote
control and wait
until it stops by
torque
OPEN LIMIT by torque 3 0 (*)
CLOSING speed 4 4
6 (*)
8
LED lights up once
OPENING speed 5
% CLOSING torque 6 2 = 50%
5 = 75%
9 = 100% (*)
% OPENING torque 7
CW/CCW 8 0 = CW (*)
1 = CCW
BLINKER/local selector 4
0 = off (*)
1 = Blinker
2 = Loc. Sel.

Quick Start Guide
VCIOM-08536-US Rev. 0
F02/EPI2 Base and OM1 Card
April 2018
OM1 Card
F02/EPI2 Quarter-Turn Electric Actuator Figure 3
Input Signal Configuration
SW5
Confirmation Push Button
SW2
Rotary Switch
SW8 SW7 SW9
Enter
Configuration
Red LED
Input Signal Configuration
SW3
Enable Configuration Mode
SW4
SW6 SW1
Output Signal Configuration
Hardware Configuration
Input Signal
SW3 SW5
1 2 1
0-10V ON OFF OFF
4-20mA OFF ON ON
Output Signal
SW1 SW6
1 2 3 4 1
0-10V OFF ON ON OFF ON
4-20mA ON OFF OFF ON OFF
Table 2.
SW7 Position Relays 0 1 2 3 4 5 6 7 8 9
Description Inactive 2% 12,50% 25% 37,50% 50% 62,50% 75% 87,50% 99%
WARNING
For complete Instruction & Warning see the VCIOM-01494 INSTALLATION AND MAINTENANCE INSTRUCTIONS. HARDWARE conguration MUST be done with system
OFF (NO power supply).SW3 and SW5 position in order to set the INPUT signal type.
HARDWARE conguration (SW1/3/5/6): This conguration is an Hardware setting; it’s mandatory to do it with power off (NO POWER SUPPLY)
Note:
(*) Factory default data
PRE-INSTALLATION: See the BASE CARD procedure.
INSTALLATION: See the BASE CARD procedures.
Rotary Switch Settings
Configurations
Move switch SW8 to
position indicated in
each row
Move switch SW7 to
position indicated in
each row
Move switch SW9 to
position indicated in
each row
SW4
Conrm
by
SW2 Red LED
SW4
RELAYS LS3-LS5 7 0=break
1=make (*)
Any position
Enter set up conguration moving SW4 to ON
Push
LED lights up once
Exit set up conguration moving SW4 to 1 (Run Setting)
RELAYS LS4-LS6 8
POSITION Relays LS3 0 0 to 9 [0=(*)]
POSITION Relays LS4 1 0 to 9 [3=(*)]
POSITION Relays LS5 2 0 to 9 [7=(*)]
POSITION Relays LS6 3 0 to 9 [9=(*)]
SET Input as “4-20mA” 9 0=off
1=on (*) 4
SET 0% input 4-20mA
4
0 = 4mA (*)
Any position
SET 100% input 4-20mA 1 = 20mA (*)
SET Input as “0-10V”
9
0=off (*)
1=on 5
Feedback mA or Vdc 2= mA (*)
3= Volt 1
Modulation 0=off (*)
1=on 3
See table 2
www.emerson.com
©2018 Emerson. All rights reserved.
The Emerson logo is a trademark and service mark of Emerson Electric Co.
The contents of this publication are presented for information purposes
only, and while every effort has been made to ensure their accuracy,
they are not to be construed as warranties or guarantees, express or
implied, regarding the products or services described herein or their
use or applicability. All sales are governed by our terms and conditions,
which are available on request. We reserve the right to modify or
improve the designs or specications of our products at any time
without notice.
For complete list of sales and manufacturing sites, please visit
www.emerson.com/actuationtechnologieslocations
Or contact us at info.actuation [e-mail]
World Area Con÷guration Centers (WACC) offer sales support, service,
inventory and commissioning to our global customers.
Choose the WACC or sales of÷ce nearest you:
MIDDLE EAST & AFRICA
P. O. Box 17033
Jebel Ali Free Zone
Dubai
T [phone]
P. O. Box 10305
Jubail 31961
Saudi Arabia
T [phone]
24 Angus Crescent
Longmeadow Business Estate
East
P.O. Box 6908 Greenstone
1616 Modderfontein Extension 5
South Africa
T [phone]
EUROPE
Holland Fasor 6
Székesfehérvár 8000
Hungary
T [phone]
Strada Biffi 165
29017 Fiorenzuola d’Arda (PC)
Italy
T [phone]
NORTH & SOUTH AMERICA
19200 Northwest Freeway
Houston TX 77065
USA
T [phone]
Av. Hollingsworth
325 Iporanga Sorocaba
SP 18087-105
Brazil
T [phone]
ASIA PACIFIC
No. 9 Gul Road
#01-02 Singapore 629361
T [phone]
No. 1 Lai Yuan Road
Wuqing Development Area
Tianjin 301700
P. R. China
T [phone]