Emerson MRLDS-450 User manual

Document Part # 026-4419 Rev 0 Page 1 of 6
©2020 Emerson Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.emerson.com for the latest technical documentation and updates.
Note: Installing the MRLDS-450 requires version E2E 4.10F01 or
later. You must add a description file for version E2 3.10F01 or less.
New Installation: Uploading the MRLDS-450
Description File to E2
The MRLDS-450 requires adding a description file
(P/N 527-0754) and license key to E2 version 3.0X or later.
Contact Customer Service to obtain this information:
Email: Solutions.Cust[email protected]om
Phone: [phone] Option 4
Note: UltraSite32 software should be installed to perform a
description file upload.
Connect to E2 using UltraSite32
1. Launch UltraSite program and login.
2. View the Directory Level and then Site Level.
3. Right-click Site Level and click Connect.
4. Locate the E2 where the MRLDS_450.dsc will be installed.
5. Right-click the unit and select Upload Description File.
6. Click Browse to select the appropriate description file (5270754.dsc) file for MRLDS-450 from the
computer and click Open.
7. Click Upload. A window will display the description file was successfully imported. Click OK. The
description file should appear inside the window.
8. Once completed, disconnect from the E2 and reboot the E2 controller.
Note: Do not omit the step of rebooting the controller.
MRLDS-450
Installation Guide
MRLDS-450 Application In E2

Document Part # 026-4419 Rev 0 Page 2 of 6
©2020 Emerson Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.emerson.com for the latest technical documentation and updates.
Device Setup
E2 Serial Port Setup
1. Log into the E2 controller.
2. Press I, , , and (General Controller Information), then press Btwice to move to
the C3: Serial tab.
3. Press the down arrow key to the COM Connection where the device is wired.
4. Press D(LOOK UP) and select MODBUS-1, MODBUS-2 or MODBUS-3, then press >to set
configuration.
5. Press Dto select options and set the MODBUS connection as follows:
6. Press >to set configuration, then Jto save changes.
7. Press Hto return to the Home screen.
MODBUS Connection
COM Baud: 19200 Baud
COM Data Size: 8
COM Parity Even
COM Stop Bits: 1
Figure 1 - E2 Device and COMM Setup

Document Part # 026-4419 Rev 0 Page 3 of 6
©2020 Emerson Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.emerson.com for the latest technical documentation and updates.
Adding the MRLDS-450 Application in E2
1. Press Ithen , , and to enter Connected I/O Boards and Controllers.
2. Press Bto move to the C3: ECT tab. Highlight the MRLDS-450 application and enter the desired
number of devices under Quantity up to a maximum of 15.
3. Press Jto save the changes.
4. Press Hto return to the Home screen.
Commissioning the MRLDS-450
1. Press Ithen , , and to enter the Network Summary screen.
2. Highlight the MRLDS-450 to be commissioned and press D
Figure 2 - ECT Tab
Figure 3 - Network Summary Screen

Document Part # 026-4419 Rev 0 Page 4 of 6
©2020 Emerson Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.emerson.com for the latest technical documentation and updates.
3. If a box with Select Network appears on the screen, select the MODBUS number where you
configured the device – either MODBUS-1, MODBUS-2, or MODBUS-3 and press >
4. Select the address for the device and press >
Note: The MODBUS address must be the same as the address assigned on the device.
Figure 4 - Select MODBUS output
Figure 5 - Select Device Address

Document Part # 026-4419 Rev 0 Page 5 of 6
©2020 Emerson Retail Solutions, Inc. This document may be photocopied for personal use.
Visit our website at http://www.emerson.com for the latest technical documentation and updates.
5. A window will appear. Press >to continue.
6. Press Jto save the assigned address.
7. Press Hto return to the Home screen and press Ithen , , and to enter the
Network Summary screen again.
8. After a few seconds, the MRLDS-450 should appear Online.
Figure 6 - Set the Physical Address for the MRLDS-450
Figure 7 - MRLDS-450 Network Summary Screen Online Status

This document may be photocopied for personal use.
Visit our website at http://www.emerson.com for the latest technical documentation and updates.
Join Emerson Technical Support on Facebook http://on.fb.me/WUQRnt
For Technical Support call 770-425-2724 or email [e-mail]
The contents of this publication are presented for informational purposes only and they are not to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or
applicability. Emerson Retail Solutions, Inc. and/or its affiliates (collectively “Emerson”), reserves the right to modify the designs or specifications of such products at any time without notice. Emerson does not assume
responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use and maintenance of any product remains solely with the purchaser and end-user.
Emerson is a trademark of Emerson Electric Co. ©2020 Emerson Retail Solutions, Inc. All rights reserved.
Document Part # 026-4419 Rev 0 Page 6 of 6
Viewing the Status
1. Press Ithen , , and (this is equivalent to pressing I, , ) or use
the cursor to navigate to MRLDS-450 and press >
2. View the status of the detector on the MRLDS-450 Summary screen and press Eto go to Setup.
Figure 8 - Configured Applications
Figure 9 - MRLDS-450 Status Screen