Emerson CSI 2140 User manual

Quick Start Guide
MHM-97430, Rev 4
March 2016
CSI 2140 Machinery Health™ Analyzer
Quick Start Guide

Copyright
© 2016 by Emerson Process Management. All rights reserved.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language in any form by any means without the written permission
of Emerson.
Disclaimer
This manual is provided for informational purposes. EMERSON PROCESS MANAGEMENT MAKES
NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. Emerson Process Management shall not be liable for errors, omissions, or
inconsistencies that may be contained herein or for incidental or consequential damages in
connection with the furnishing, performance, or use of this material. Information in this
document is subject to change without notice and does not represent a commitment on the part
of Emerson Process Management. The information in this manual is not all-inclusive and cannot
cover all unique situations.
Trademarks and Servicemarks
See http://www2.emersonprocess.com/siteadmincenter/PM Central Web Documents/marks.pdf
All other marks are property of their respective owners.
Patents
The product(s) described in this manual are covered under existing and pending patents.
March 2016 Quick Start Guide
MHM-97430 Rev 4 3

Quick Start Guide March 2016
4MHM-97430 Rev 4

Introduction to the analyzer
Front view
CSI 2140 front panelFigure 1:
A. Home key - Return to the Home screen from any program.
B. Reset key - Return to the main menu in a program.
C. Function keys - Display menu options.
D. Enter key - Select a menu or option.
E. Keypad backlight key - Turn on the backlight under the keys. (1)
F. LCD backlight key - Set the backlight for the LCD touchscreen.
G. Help key - Display Help text for a key.
H. Power key -Turn the analyzer on or off, or put the analyzer in standby.
I. Battery LED - Green light if the battery pack is charged; amber when charging.
J. Status LED - Blue light flashes each time you press a key or option, blinks in
power save mode, and remains solid in standby mode.
(1) To comply with relevant safety certifications, the CSI 2140 labeled "ATEX/IECEx Zone 2" does not
have a keypad backlight.
March 2016 Quick Start Guide
MHM-97430 Rev 4 5

K. Arrow keys - Move through menus.
L. ALT key - Display an alternate screen, if available.
M. Back key - Back up to the main menu in a program.
Top view
ConnectorsFigure 2:
A. Power supply connector.
B. Ethernet port.
C. Micro USB port.
D. Wireless LED.
E. Bluetooth® LED.
CAUTION!
To prevent damage to the analyzer:
•Do not connect a signal outside the range of 0 to 24 volts into the Accel
input of the CSI 2140.
•Do not connect a signal outside the range of +/- 24 volts into the Volts /
Tach input of the CSI 2140.
Turn on the analyzer for the first time
You need to activate the battery pack before you can turn on the analyzer for
the first time. The battery pack is shipped in storage mode to protect the
battery charge. Connect the provided power supply cord into an outlet and
to the analyzer to activate the battery pack.
Quick Start Guide March 2016
6MHM-97430 Rev 4

Procedure
1. Connect the provided power supply cord into an outlet and to the
analyzer.
Note
Refer to precautions for the battery pack and power adapter.
The Battery LED is amber to indicate the battery pack is charging. The
analyzer is activated.
2.
Press and hold the power key to turn the analyzer on.
The Home screen appears when you turn on the analyzer. The time and
date are set to a default value.
3. To set the time and date, press Home > ALT > F3 Set Time.
Battery pack
A rechargeable Lithium-Ion battery pack powers the analyzer. A typical
charge should last for more than 8 hours of continuous use. The analyzer
displays a low-battery warning when the remaining charge reaches a set
level; the default is 15 percent. If the battery pack fully discharges, you do not
lose any data or settings.
The battery pack is shipped in storage mode to protect the battery charge.
Refer to Turn on the analyzer for the first time to activate the battery pack.
You do not need to discharge or calibrate the battery pack. The hardware
optimizes battery pack performance. Contact technical support if you
experience any problems or for instructions on how to store or replace the
battery pack.
WARNING!
Use only Emerson battery packs with the CSI 2140. The analyzer will not
function if a non-Emerson battery pack is used. Lithium-Ion batteries have
very specific charging requirements. Emerson power supplies and chargers
are designed to work with the Emerson Lithium-Ion battery pack. Using
battery packs other than approved Emerson battery packs could not only
void the warranty, but could also be hazardous.
March 2016 Quick Start Guide
MHM-97430 Rev 4 7

Charge the battery pack
The analyzer is fully operational during charging. As a best practice, charge
the battery pack frequently. Emerson recommends you charge the battery
pack the night before you intend to use it.
WARNING!
•Use only Emerson-supplied power supplies and chargers approved for use
with the CSI 2140 and Emerson battery packs. Using any power supplies
and chargers other than approved Emerson power supplies and battery
packs could not only void the warranty, but will also most likely damage
the analyzer or the battery pack.
•When charging the CSI 2140 with the battery pack or the battery pack by
itself, ensure the ambient temperature where charging is occurring is 50°
F to 95° F (10° C to 35° C).
•Charge the battery pack only in a non-hazardous area.
Procedure
1. Remove the rubber plug on the top of the analyzer.
2. Insert the power supply connector into the analyzer. The analyzer can be
powered on or off.
3. Plug the AC connector on the power supply into a standard AC outlet,
ranging from 100 VAC to 250 VAC, 50-60 Hz. A full recharge may take
four hours.
The back of the analyzer may feel warm during charging. The power
supply can remain connected to the analyzer after charging completes.
You cannot overcharge the battery pack.
Attach the shoulder strap
1. Press and hold the button on the strap connector, and insert it into the
connectors on the sides of the analyzer or the CSI 2140 Four-Channel
Input Adapter, if attached.
2. To release the strap, press and hold the button on the connector and
then pull.
Use the stand
1. To put the stand in the upright position, grab the stand and pull up until
the stand locks.
2. To release the stand, place the analyzer face down, grab the base of the
stand, and gently pull.
Quick Start Guide March 2016
8MHM-97430 Rev 4

The lock releases, and you can push the stand toward the analyzer.
Release the standFigure 3:
Home screen
The Home screen appears when you turn on the analyzer by pressing the
power key.
March 2016 Quick Start Guide
MHM-97430 Rev 4 9

Home screenFigure 4:
A. An alternate screen (ALT) includes additional options.
B. Current time and date.
C. Default splash screen.
D. Remaining battery pack charge.
E. Number of supported channels for the analyzer.
F. Serial number.
G. Group number for updating multiple analyzers at one site.
H. Available internal memory.
Home screen programs and settings
The Home screen has two alternate screens that display programs and
settings. ALT1 or ALT2 appears at the top of the screen and the function keys
are outlined in yellow. To switch ALT screens, press the ALT key or the ALT text
on the touchscreen.
ALT1 keys
Option Description
F1 Intentionally blank.
F2 File Utility Copy, delete, or move routes or jobs saved in the analyzer internal
memory or a memory card.
Quick Start Guide March 2016
10 MHM-97430 Rev 4

Option Description
F3 Intentionally blank.
F4 Set Display Units Set the default display units for the measurement values and plots.
F5 Comm Setup Set the communication options to connect the analyzer to AMS Machinery
Manager. You can also set up the Bluetooth functionality.
F6 Program Manager Update the programs, add new programs, delete unused programs, or
change the splash screen. A password is required to delete programs.
F7 Analyze or Adv.
Analyze
Collect data using predefined measurements called Analysis Experts, or
create your own measurements in Manual Analyze.
F8 Route Collect data using a route created in AMS Machinery Manager. You cannot
create or modify routes on the analyzer.
F9 Balance Balance a machine. Balance is an optional program that you load onto the
analyzer.
F10 Basic Laser Align
or Adv. Laser Align
Align machines. The Basic Laser Alignment Application comes with
analyzers that have the wireless option. The Advanced Laser Alignment
Application is an optional program that you can load onto the analyzer
and has more functions than the Basic application.
F11 Adv. Transient Collect large, unbroken time waveforms similar to a digital recorder.
Advanced Transient is an optional program that you load onto the
analyzer.
F12 ODS/Modal Collect cross channel data for animated analysis of a machine. ODS/Modal
is an optional program that you load onto the analyzer.
ALT2 keys
Option Description
F1 Version View the versions of the firmware and programs installed on your analyzer.
F2 General Setup Modify settings for the analyzer screen, keys, and print functionality.
F3 Set Time Set the time and date in the analyzer.
F4 Memory Utility View information about the internal memory.
F5 Battery Utility View information about the battery pack.
F6 View Error Log View information about any errors the firmware generated.
F7 Connect For
Printing
Connect to AMS Machinery Manager to print files or screen captures.
F8 Intentionally blank.
F9 Intentionally blank.
F10 Intentionally blank.
F11 Intentionally blank.
F12 Intentionally blank.
Touchscreen
The touchscreen and function keys let you access the menu options and
enter text. If the touchscreen does not respond accurately, calibrate the
touchscreen.
March 2016 Quick Start Guide
MHM-97430 Rev 4 11

WARNING!
Clean the touchscreen only in a non-hazardous area. An electrostatic
discharge is possible when you clean the equipment exterior. Do not use any
abrasive or corrosive chemicals or materials. Do not use petroleum distillates
and ketone solvents, for example, acetone, gasoline and kerosene. Use a dry,
lint-free towel or cloth dampened with a mild soap and water solution.
Note
To prevent permanent damage to the touchscreen, never use sharp objects
or excessive pressure with your fingers or stylus. Lightly tap the screen.
Common analyzer settings
Task Key sequence
Enable or disable the beeper for
key presses
Home > ALT > F2 General Setup > F2 Set Keypad Beeper
Set a timer to enter standby
when inactive
Home > ALT > F2 General Setup > F4 Set Standby Time
Set a timer to turn off the
backlight when inactive
Home > ALT > F2 General Setup > F5 Set Backlight Time
Set the low-battery warning
level
Home > ALT > F2 General Setup > ALT > F3 Set Warning Level
Set the number of seconds to
hold the power key before the
analyzer shuts down
Home > ALT > F2 General Setup > ALT > F4 Set Hold Time
Set the connection type to use
with AMS Machinery Manager
Home > F5 Comm Setup > F1 Set Connect Port
Set the default display units for
all programs
Home > F4 Set Display Units
Set the date and time Home > ALT > F3 Set Time
View the analyzer firmware
version
Home > ALT > F1 Version
CSI 2140 Four-Channel Input Adapter
The CSI 2140 Four-Channel Input Adapter expands the capabilities of your CSI
2140 by enabling four inputs.
WARNING!
Use the CSI 2140 Four-Channel Input Adapter in non-hazardous areas only.
Quick Start Guide March 2016
12 MHM-97430 Rev 4

The CSI 2140 Four-Channel Input Adapter has two sides that display
connectors for Volts and Accel. Each side has a connector labeled "To CSI
2140". Use the appropriate Interface cable to connect the CSI 2140 Four-
Channel Input Adapter to the CSI 2140. The Accel side has a 5-pin connector.
The Volts side has an 8-pin connector.
Connect to the CSI 2140
Attach the CSI 2140 Four-Channel Input Adapter to the shoulder strap
connectors on each side of the analyzer, and press the tabs until they click
into place. To release the adapter, press the tabs on each side of the CSI 2140
Four-Channel Input Adapter. To attach the shoulder strap, use the
connectors on the sides of the CSI 2140 Four-Channel Input Adapter.
Use the appropriate Interface cable to connect the CSI 2140 Four-Channel
Input Adapter to the CSI 2140.
Side Required interface cable
Accel A40ADAPTR Accel Interface Cable
Volts A40ADAPTR Tach/Volts Interface Cable
March 2016 Quick Start Guide
MHM-97430 Rev 4 13

CSI 2140 Four-Channel Input Adapter attached to the CSI 2140
without the interface cable
Figure 5:
Use with the CSI 2140
The CSI 2140 Four-Channel Input Adapter requires no additional setup,
except in the Balance program. For the Balance program, you must enable
the mux option to use the CSI 2140 Four-Channel Input Adapter.
To access the other connectors, turn the adapter over and connect to the CSI
2140 using the appropriate Interface cable.
Multiple inputs
Your analyzer may support up to four channels in each program to
simultaneously collect data. To use the multi-channel functionality, set the
number of inputs in the Input Setup menu in each program, set up a sensor
for each input, and use a connection listed below. For routes, you need to set
up the inputs and sensors in AMS Machinery Manager.
Quick Start Guide March 2016
14 MHM-97430 Rev 4

Number of
inputs Connection options
1 Use a single cable.
2•Use two single cables on two separate inputs (acceleration only).
•Use a splitter cable on one input.
•Use the CSI 2140 Four-Channel Input Adapter.
3•Use a splitter and one single cable on two separate inputs.
•Use the CSI 2140 Four-Channel Input Adapter.
•Use the triaxial accelerometer with a single cable.
4•Use two splitters on two separate inputs.
•Use the CSI 2140 Four-Channel Input Adapter.
•Use the triaxial accelerometer with a single cable on one accelerometer
input and another cable on the other accelerometer input.
CSI 2140 for use in hazardous locations
Be aware of the appropriate approvals before operating the CSI 2140 in
hazardous locations.
Each CSI 2140 has a label attached to the back of the unit that designates
with approval markings the approved locations for use:
Label Approved locations
CSA General Safety Non-rated. Do not use in a hazardous location.
Class I Division 2 Approved for use in a Class I Division 2 hazardous location.
ATEX/IECEx Zone 2 Approved for use in an ATEX/IECEx Zone 2 and Class I
Division 2 hazardous location.
Be aware of the following when using the CSI 2140 in a hazardous location:
March 2016 Quick Start Guide
MHM-97430 Rev 4 15

WARNING!
•The USB port must only be used in a non-hazardous location.
•The Ethernet port must only be used in a non-hazardous location.
•Do not use the CSI 430 SpeedVue Sensor in a hazardous location.
•The battery must only be charged and/or replaced in a non-hazardous
location.
•If a unit shows any sign of damage, please return for repair.
•If leaving the device unattended outdoors, it is recommended to store
the unit in a shaded area or with the LCD facing down.
•The front touch screen must be protected from impact.
•Outputs are intrinsically safe when implemented per drawing D25671 for
use in an ATEX/IECEx Zone 2 hazardous environments.
•Outputs are intrinsically safe when implemented per drawing D25639 for
use in a Class I Division 2 hazardous environment.
Refer to Emerson Safety Addendum D25670 for complete information on
certifications and conditions of safe use in ATEX/IECEx Zone 2 locations. Only
ATEX/IECEx Zone 2 units will include this safety addendum in the package.
Notes
•To comply with relevant safety certifications, the CSI 2140 labeled "ATEX/
IECEx Zone 2" does not have a keypad backlight.
•CSI 430 SpeedVue Sensor may not be compatible with the CSI 2140
labeled "ATEX/IECEx Zone 2." The CSI 430 is not permitted in hazardous
areas; and it may not function with the ATEX-certified CSI 2140 even in a
safe area.
Quick Start Guide March 2016
16 MHM-97430 Rev 4

Collect route data
The following section describes how to collect route data. By default, the CSI
2140 and AMS Machinery Manager Data Transfer use USB communication to
transfer routes. Ensure your AMS Machinery Manager database has a route
before you proceed. See the AMS Machinery Manager documentation for
information about creating routes.
Note
You must use AMS Machinery Manager version 5.6 or newer to connect to
the CSI 2140.
Step 1: Load a route into the analyzer
Task Steps
Connect to AMS
Machinery Manager
1. Remove the rubber plug on the top of the analyzer.
2. Connect the USB cable to the CSI 2140 and the computer where
AMS Machinery Manager is installed.
3. Open and log in to AMS Machinery Manager.
4. Click the Data Transfer tab.
5. On the analyzer, press Home > F8 Route > F7 Connect for Transfer.
Load a route from AMS
Machinery Manager
1. In Data Transfer, select the database in the Navigator.
2. Drag and drop the route from the database to the connected
analyzer in Data Transfer.
3. Click Disconnect in AMS Machinery Manager.
Activate a route On the analyzer, select a route and press F3 Activate Route on the Route
Management screen.
Route Data Collection screen and options
Route Data Collection is the main menu for Route. After you activate a route,
the analyzer displays the Route Data Collection screen.
March 2016 Quick Start Guide
MHM-97430 Rev 4 17

Route Data Collection screenFigure 6:
A. Displays the live and collected data.
B. Status field for measurements, notes, and field alerts.
C. Date and overall value of the last data collected on this point.
D. Measurement reading (overall vibration level).
E. Measurement point description.
F. Equipment description.
G. Measurement point number.
H. Equipment ID.
I. Group and channel number of the measurement point.
J. Three-character measurement point ID.
K. An alternate (ALT) screen includes additional options.
ALT1 keys
Option Description
F1 Prev Point Move to the previous measurement point on the equipment. If the first
point on the equipment displays and you press F1 Prev Point, the analyzer
displays the last point on the previous equipment.
F2 Prev Equip Move to the previous equipment in the route. If the first equipment
displays and you press F2 Prev Equip, the analyzer displays the last
equipment.
F3 Equip List View all equipment and measurement points in a route.
Quick Start Guide March 2016
18 MHM-97430 Rev 4

Option Description
F4 Notes Create, add, or delete notes.
F5 Plot Data View the collected data on one or more plots.
F6 Clear Data Delete data from the current measurement point.
F7 Next Point Move to the next measurement point on the equipment. If the last point
on the equipment displays and you press F7 Next Point, the analyzer
displays the first point on the next equipment.
F8 Next Equip Move to the next equipment in the route. If the last equipment displays
and you press F8 Next Equip, the analyzer displays the first equipment.
F9 Listen To Live Data Listen to vibration using headphones.
F10 Field Alert Add or remove a field alert from a measurement point. Use field alerts to
identify a point for further investigation.
F11 View Parms View the Analysis Parameter Set with measured values, percent of fault,
and any parameters that may be in alert.
F12 Run Analyze Open the Analyze program to collect additional data on the current
measurement point.
ALT2 keys
Option Description
F1 User Setup Set options for your route. You can set the plots to display live and
collected data, parameters to collect route data, and the amount of
route data to store.
F2 Override Control Set up a different sensor than what is specified for the route.
F3 Out Of Service Label equipment as out of service and skip the measurement.
F4 Intentionally blank.
F5 Tach Setup Set up and save a tachometer configuration. You can also open, edit,
delete, or rename a configuration.
F6 New RPM Enter a new RPM or load for equipment using a different value than
defined in the route.
F7 Exit Route Close Route and return to the Home screen.
F8 Intentionally blank.
F9 Route Mgnt Load, delete, or activate routes. You can also connect to AMS Machinery
Manager Data Transfer.
F10 View Trend History Display trend data for the current point in a graphical format. The data
includes both historical data downloaded from the database and new
data collected with the analyzer.
F11 Print Route Report Send a route report to the memory card or to AMS Machinery Manager,
depending on the default print mode for the analyzer.
F12 More Point Info View information about the route and the current measurement point.
March 2016 Quick Start Guide
MHM-97430 Rev 4 19

Step 2: Review data collection and display parameters
The default parameters should be appropriate for most routes. Press Enter or
the Back key when you are finished.
Task Steps
Set the plot type for
collected data
From the Route Data Collection screen, press ALT > F1 User Setup > F2
Select Data Display.
Automatically go to the
next measurement point
From the Route Data Collection screen, press ALT > F1 User Setup > F3
Point Advance Mode.
Set the route storage
mode
From the Route Data Collection screen, press ALT > F1 User Setup > F5
Data Storage Mode.
Set the overlap From the Route Data Collection screen, press ALT > F1 User Setup > F6
Percent Overlap.
Set the plot type for live
data
From the Route Data Collection screen, press ALT > F1 User Setup > F8
Select Live Display.
Set the overall mode From the Route Data Collection screen, press ALT > F1 User Setup > F9
Set Overall Mode.
Set the integrate mode From the Route Data Collection screen, press ALT > F1 User Setup >
F10 Set Integrate Mode.
View the Analysis
Parameters
From the Route Data Collection screen, press F11 View Parms.
Step 3: Collect route data
Task Steps
Collect route data 1. Attach the sensor to the equipment and the analyzer.
2. From the Route Data Collection screen, press Enter.
Move to the next
measurement point
Press F7 Next Point.
Move to the next
equipment
Press F8 Next Equip.
Plot route data Press F5 Plot Data. Press Enter to close the plot view.
Optional: Mark a
frequency on a plot with a
cursor
Press F10 Cursor Mark or touch the plot. Use the arrow keys to move
the cursor. The cursor value displays at the bottom of the screen.
Optional: Run the Analyze
program for a route
measurement point
1. From the Route Data Collection screen, press F12 Run Analyze.
2. Select an Analysis Expert or a measurement in Manual Analyze.
3. Follow the prompts and press Enter to collect data.
4. Press F9 Store Data to save the data.
Run Analyze to collect data for a route measurement point
If you see unusual data for a measurement point, you can open the Analyze
program to collect additional data to troubleshoot the problem. Press the F12
Run Analyze key on the Route Data Collection screen to open Analyze.
Quick Start Guide March 2016
20 MHM-97430 Rev 4