Emerson SolaHD STC-DRS Series User manual

Surge Protective Devices
STC-DRS Series
DIN Rail Protection

Safety Information
Important Information
Read these instructions carefully and look at the equipment to become
familiar with the device before trying to install, operate, service or maintain it.
The following special messages may appear throughout thisbulletin or on the
equipment to warn of potential hazards or to call attention to information that
clarifies or simplifies a procedure.
The addition of either symbol to a “Danger”or “Warning” safety label
indicates that an electrical hazard exists which will result inpersonal
injury if the instructions are not followed.
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messagesthat follow this
symbol to avoid possible injury or death.
DANGER
DANGER indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING
WARNING indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided,
could result in minor or moderateinjury.
NOTICE
NOTICE is used to address practices not related to physical injury. The safety
alert symbol shall not be used with this signal word.
Please Note
Electrical equipment should be installed, operated, serviced, and maintained only
by qualified personnel. No responsibility is assumed by Appleton Grp LLC d/b/a
Appleton Group for any consequences arising out of the use of this material.
A qualified person is one who has skills and knowledge related to the
construction, installation, and operation of electrical equipment andhas received
safety training to recognize and avoid the hazards involved.

Page: 1
STC-DRS Series
Introduction
The STCDRS036 is a DIN Rail mountable, single pair surge suppression module implementing three stage
hybrid technology. This module addresses over-voltage transients with gas tubes and silicon avalanche
components. In addition, sneak currents are mitigated with resetable fuses (PTCs). The PTCs increase
resistance several orders of magnitude when over-currents exceed operating limits. A normal state resumes
when the over-current condition is removed. The ability to self-restore in this manner signicantly increases
suppressor performance and survivability.
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
• Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See NFPA 70E,
NOM-029-STPS or CSA Z462.
• This equipment must only be installed and serviced by qualied electrical personnel.
• Turn o󰀨 all power supplying this equipment before working on or inside equipment.
• Always use a properly rated voltage sensing device to conrm power is o󰀨.
• Replace all devices, doors and covers before turning on power to this equipment.
• This equipment must be e󰀨ectively grounded per all applicable codes. Use an equipment-grounding conductor to
connect this equipment to the power system ground.
• Conrm that the Surge Protective Device voltage rating on the module or nameplate label is not less than the
operating voltage.
• For 6-35VDC models, do not place in service on any signal line capable of continuously supplying
more than 150mA.
Failure to follow these instructions will result in death or serious injury.
WARNING: This product can expose you to chemicals including DINP, which is known to the State of California
to cause cancer, and DIDP which is known to the State of California to cause birth defects or other reproductive
harm. For more information go to: www.P65Warnings.ca.gov.

STC-DRS Series
Page: 2
NOTICE
HAZARD OF MIS-INSTALLATION
• Only install this protective device in indoor applications and on communication loop circuits which have been
isolated from the public switch telephone network (PSTN).
• Do not expose the communication loop to contact with the electric light or power conductors.
• Install the protectors as per the applicable requirements of the National Electric Code, ANSI/NFPA 70.
Failure to follow these instructions can result in equipment damage.
Installation
1. Turn off power prior to installing SPD.
2. Install SPD in suitable enclosure.
3. Connect load wires to output side of SPD.
4. Connect source wires to input side of SPD.
5. Do not exceed 150mA continuous current.
6. Turn on power and verify operation.
General Technical Specifications 0-36VDC Models
Operating Voltage 0-36 VDC
Breakdown Voltage 43 VDC
Operating Current 0.15 A
Peak Surge Current 10 kA (8x20µs)
Max Current Ip (Occurrences) >100 (10x1000µs)
Typical Capacitance 1500pf
Nominal Series Resistance 5 Ω
Response Time < 1 nanosecond
Operating Temperature -40°C to 85°C
Certifications UL 497B
Limited Warranty 5 years

Page: 3
STC-DRS Series
Field Side
(Line)
Load Side
(Load)
LINE
LINE
SHIELD
2.95
[74.9]
2.35
[59.7]
Ground
2.25
[57.2]
0.8
[20.3]
1.1
[27.9]
Wire Size Range = 22-12 AWG
Terminal Torque Rating = 0.8 Nm (7 in-lb)
Ordering Information
MODEL APPLICATION
STCDRS036 0-36 VDC

STC-DRS Series
Page: 4
Technical Support
Website: www.solahd.com
Technical Support E-Mail: [e-mail]
Toll-Free: [phone]
USA: [phone]
Warranty
Please refer to the “Terms & Conditions of Sale” document.
While every precaution has been taken to ensure accuracy and completeness in this manual, Appleton Grp LLC d/b/a Appleton Group
assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions.

Page: 5
Notes

STC-DRS Series
A272-139 Rev. 3 12/2020
The Emerson logo is a trademark and service mark of Emerson Electric Co.
Appleton Grp LLC d/b/a Appleton Group. SolaHD is a registered trademark of Appleton Grp LLC.
All other marks are the property of their respective owners. © 2020 Emerson Electric Co. All rights reserved.
United States
(Headquarters)
Appleton Grp LLC
9377 W. Higgins Road
Rosemont, IL 60018
United States
T [phone]
Australia Sales Office
Bayswater, Victoria
T [phone]
Europe
ATX SAS
Espace Industriel Nord
35, rue André Durouchez,
CS 98017
80084 Amiens Cedex 2
France
T [phone]
China Sales Office
Shanghai
T [phone]
Canada
EGS Electrical Group Canada
Ltd.
99 Union Street
Elmira ON, N3B 3L7
Canada
T [phone]
Middle East Sales Office
Dammam, Saudi Arabia
T [phone]
Chile Sales Office
Las Condes
T [phone]
India Sales Office
Chennai
T [phone]
Korea Sales Office
Seoul
T [phone]
PN#9634_r
Asia Pacific
EGS Private Ltd.
Block 4008, Ang Mo Kio
Ave 10,
#04-16 TechPlace 1,
Singapore 569625
T [phone]
Latin America
EGS Comercializadora
Mexico S de RL de CV
Calle 10 N°145 Piso 3
Col. San Pedro de los Pinos
Del. Álvaro Obregon
Ciudad de México. 01180
T [phone]