Emerson SOLAHD STCPOE65FF User manual

Surge Protective Devices
STCPOE65FF
RJ-45 Female-to-Female
Dimensions: (in./[mm]) Circuit Diagram
2.3
[58.4]
0.8
[20.3]
1.0
[25.4]
2
2
1
1
IN OUT
Typical
(4x)
Low Capacitance
Neg Steering
Diodes
Low Capacitance
Pos Steering
Diodes
Silicon
Avalanche
Diodes
General Technical Specifications
Operating Voltage Up to 57 VDC
Breakdown Voltage 68 VDC
Operating Current 350 mA
Peak Surge Current 60 A (10 x 1000 µs)
Frequency Range 0 to 250 MHz
Insertion Loss < 0.1 dB at 20 MHz
SPD Technology Silicon Avalanche Diode (SAD)
Connection Type Female-Female RJ-45 Jacks
Operating Temperature -40°C to +85°C
Dimensions (in. / mm.) 0.8 x 1.0 x 2.3 in. [20.3 x 25.4 x 58.4 mm.]
Weight (oz. / kg.) 1 oz. [0.02 kg.]
Limited warranty 5 year

Safety Information
Important Information
Read these instructions carefully and look at the equipment to become
familiar with the device before trying to install, operate, service or maintain it.
The following special messages may appear throughout thisbulletin or on the
equipment to warn of potential hazards or to call attention to information that
clarifies or simplifies a procedure.
The addition of either symbol to a “Danger”or “Warning” safety label
indicates that an electrical hazard exists which will result inpersonal
injury if the instructions are not followed.
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messagesthat follow this
symbol to avoid possible injury or death.
DANGER
DANGER indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING
WARNING indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided,
could result in minor or moderateinjury.
NOTICE
NOTICE is used to address practices not related to physical injury. The safety
alert symbol shall not be used with this signal word.
Please Note
Electrical equipment should be installed, operated, serviced, and maintained only
by qualified personnel. No responsibility is assumed by Appleton Grp LLC d/b/a
Appleton Group for any consequences arising out of the use of this material.
A qualified person is one who has skills and knowledge related to the
construction, installation, and operation of electrical equipment andhas received
safety training to recognize and avoid the hazards involved.

STCPOE65FF
Introduction
The SolaHD STCPOE65FF is designed to work on Category 5 Power-Over-Ethernet transmission lines as well as
Category 6 applications.
This device limits surges and transients at computers and video equipment.
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
• Apply appropriate personal protective equipment (PPE) and follow safe electrical work practices. See NFPA 70E,
NOM-029-STPS or CSA Z462.
• This equipment must only be installed and serviced by qualied electrical personnel.
• Turn o󰀨 all power supplying this equipment before working on or inside equipment.
• Always use a properly rated voltage sensing device to conrm power is o󰀨.
• Replace all devices, doors and covers before turning on power to this equipment.
• This equipment must be e󰀨ectively grounded per all applicable codes. Use an equipment-grounding conductor to
connect this equipment to the power system ground.
• Conrm that the Surge Protective Device voltage rating on the module or nameplate label is not less than the
operating voltage.
• Do not place this product in service on any line capable of supplying more than 350 mA continuously.
Failure to follow these instructions will result in death or serious injury.
WARNING: This product can expose you to chemicals including DINP, which is known to the State of California
to cause cancer, and DIDP which is known to the State of California to cause birth defects or other reproductive
harm. For more information go to: www.P65Warnings.ca.gov.
Installation
1. Turn off all power supplying this equipment before working on or inside equipment.
2. Mount the SPD as close as possible to the equipment.
3. Connect the STCPOE65FF supply cable (with RJ-45 connector) to the IN side of the SPD.
4. Connect the STCPOE65FF supply cable (with RJ-45 connector) to the OUT side of the SPD and connected
equipment.
5. Replace the barrier, cover/door and/or trim to the equipment.
6. Equipment may be re-energized after all the above steps are complete.
Technical Support
Website: www.solahd.com
Technical Support E-Mail: [e-mail]
Toll-Free: [phone]
USA: [phone]
Warranty
Please refer to the “Terms & Conditions of Sale” document.
While every precaution has been taken to ensure accuracy and completeness in this manual, Appleton Grp LLC d/b/a Appleton Group
assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions.

STCPOE65FF
A272-140 Rev. 4 12/2020
The Emerson logo is a trademark and service mark of Emerson Electric Co.
Appleton Grp LLC d/b/a Appleton Group. SolaHD is a registered trademark of Appleton Grp LLC.
All other marks are the property of their respective owners. © 2020 Emerson Electric Co. All rights reserved.
United States
(Headquarters)
Appleton Grp LLC
9377 W. Higgins Road
Rosemont, IL 60018
United States
T [phone]
Australia Sales Office
Bayswater, Victoria
T [phone]
Europe
ATX SAS
Espace Industriel Nord
35, rue André Durouchez,
CS 98017
80084 Amiens Cedex 2
France
T [phone]
China Sales Office
Shanghai
T [phone]
Canada
EGS Electrical Group Canada
Ltd.
99 Union Street
Elmira ON, N3B 3L7
Canada
T [phone]
Middle East Sales Office
Dammam, Saudi Arabia
T [phone]
Chile Sales Office
Las Condes
T [phone]
India Sales Office
Chennai
T [phone]
Korea Sales Office
Seoul
T [phone]
PN# 9637_r-
Asia Pacific
EGS Private Ltd.
Block 4008, Ang Mo Kio
Ave 10,
#04-16 TechPlace 1,
Singapore 569625
T [phone]
Latin America
EGS Comercializadora
Mexico S de RL de CV
Calle 10 N°145 Piso 3
Col. San Pedro de los Pinos
Del. Álvaro Obregon
Ciudad de México. 01180
T [phone]